VALDUS XY-11 True Wireless Earbuds User Manual
- June 9, 2024
- VALDUS
Table of Contents
VALDUS XY-11 True Wireless Earbuds
TWS XY-11
Function Instructions
Diagrammatic Sketch
- Indicator light
- Type-c interface
- Ear cap
- Touch area
Specifications
- Model: XY-11
- Bluetooth version: V5.3+EDR
- Earbud battery:30mAh
- Charging case battery:400mAh
- Power input:5V
- Product weight: about 36g
- Working time: 3.5hours
- Working voltage: 3.3V-4.2V
- Charging time: 70 minutes
- Speaker impedance: F6/322
- Frequency response: 20-20KHZ
- Transmission distance:over 10 meters
Package List
- Bluetooth headset (2PCS)
- Earphone Charging box
- Type-c charging cable
- User’s manual
- Gift package
- Earphone caps (3 pairs)
How to use
The boot
- Step 1: Open the top cover of the charging compartment.
- Step 2: Take out the two earphones, at this time the earphones are automatically turned on and matched, waiting for the mobile phone to be connected manually boot Manual boot If the headset is not in the charging compartment, press and hold the left and right ears for 2 seconds to power on.
To turn it off Headphones automatically shut down
-
Step 1: After use, remove the earphone from the ear.
-
Step 2: Put the left and right carphones into the charging compartment and cover, it will automatically shut down and charge.
Manual shutdown -
Step 1 : lf the earphones are powered on and connected to each other, press and hold the left/right ear5 Shut down in seconds.
-
Step 2: Put the left and right carphoncs into the charging compartment to charge.
Bluetooth pairing
- Step 1: Open the charging compartment.
- Step 2: Turn on the Bluetooth of the mobile phone.
- Step 3: Find the headset Bluetooth name “[XY-11]”.
- Step 4 : Click Connect.
Note: If there is pairing device information,the headset will automatically connect to the device within 2-4s. If the headset is not connected to the device,it will automatically shut down after three minutes of standby.
Operation of earphone
- (A) Answer/Hang up: Click any headset to answer/end the call. Hold down either earphone for 1.5 seconds to refuse to answer the call.
- (B) Pause/play: Click either earphone to pause or play the music.
- (C) Previous/next: During the music playing, double click the left earphone to complete the operation of the previous song. Double-click the headset on the right during the music playing to complete the next song operation.
- ( D) Volume increase and decrease: Tap the lcft carphone three timcs to incrcasc the volume. Click the right earphone three times to reduce the volume.
- (E) Wake up the voice assistant: After setting permissions on the 10S phone and screening SIRI functions, hold down the headset for 1.5 seconds to wake up SIRI.
Indicator working status
Precautions for use
-
Headphones should be slo<“ed in a dry and ventilated environment to a.void contact with oil, water. and steam.In order to avoid affecting product performance.
-
Avoid cleaning with irritating, organic solvents or materials contoining ingredient
-
Theheadsetshouldbe used. according to the correct specification requirements, and pay attention to the influence of the user environment on the headset.
To ensure a smooth connection, ii is recommended that the distance between the mobile phone and the earphone be within 10 meters. -
If the earphone fails to connect properly, do not remove the earphone without permission TI>emachinebodyanditsaccessoriesare not guaranteed otherwise.
-
To charge the earphone, please use the Ellldardcar charger or the one specified by our companyChargersrequlred
-
To ensure normal use of the earphone, ensure that the power of the earphoneissufficicnt
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device has been evaluated to meet the general RF exposure requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>