Matchmaster 04MM-RP01 Recessed Power Point Mounting Box Instruction Manual
- July 25, 2024
- Matchmaster
Table of Contents
Matchmaster 04MM-RP01 Recessed Power Point Mounting Box
Specifications
- Model: 04MM-RP01, RP02 & RP03
- Dimensions: 168x120mm
- Installation: New builds and existing builds
FAQs
- Q: Can I paint over the installed RP0x?
- A: Yes, once installed, the RP0x can be painted if required. Ensure proper drying time before use.
- Q: Do I need to disconnect existing power points during installation?
- A: No, wiring from existing power points does not need to be disconnected but must be turned off at the mains first.
PRODUCT USING INSTRUCTIONS
WARNINGS AND CAUTIONS
- To be installed by a suitably qualified installer
- To be installed and/or used by appropriate electrical codes and regulations
- If you are unsure about any part of these instructions, consult a qualified installer
IMPORTANT INSTRUCTIONS
- Read and understand all instructions. Follow all warnings and instructions marked on the product
- Do not use this product near water – eg. near a bathtub, wash basin, sink, a wet basement, or near a swimming pool
- Never push objects of any kind into this product through openings, as they may touch dangerous voltages
SAFETY INSTRUCTIONS
- Never install components during an electrical storm
- Never install components in wet locations unless the components are designed for such use
- Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface
- Note: Wiring from existing power points does not need to be disconnected but must always be turned off at the mains first.
HOW TO INSTALL IN NEW BUILDS
- Warning: To avoid fire, shock, or death, turn off the power at the circuit breaker or fuse and test the power is off before continuing.
- Choose the location for the RP0x, theinstallation requires mounting the RP0x using floating clips mounted in each corner, you will need to select a wall location free from obstructions such as timber frames, metal wall straps, etc, and please make sure there is no wall point back to back if installing into an internal wall location as this will affect the available wall depth.
- Cut out holes in wall sheeting using the template provided as a guide. Check for obstructions in the wall cavity to ensure the RP0x will fit in its location.
- RP02 & RP03 Step: Please install insert type to bezel and direct connection cables through brush opening prior to fitting RP02/03 to the wall cavity.
- Slide powerpoint or like through the back of the RP0x on an angle and push the housing into cut out until tight against the wall sheeting, if the existing wall plate is too large or the cabling is too tight you may need to disconnect the cabling from the back of the wall plate and reconnect through the RP0x.
- If wall sheeting is of hard material mark the locations of the 2 top fins and the 2 bottom fins and make small cuts until the plastic shroud is located firmly up against wall sheeting.
- Insert the RP0x into the wall and secure it in place using the preinstalled floating clips, one in each corner.
- Position the powerpoint or like into the housing and use the 2 x 13mm screws provided screw into the metal brackets to secure it in place.
- Connect the RP0x cover. The RP0x and the wall are now ready to be painted if required.
HOW TO INSTALL IN EXISTING BUILDS
- Warning: To avoid fire, shock, or death, turn off the power at the circuit breaker or fuse and test the power is off before continuing.
- Unscrew the existing point from the wall face and check for obstructions in the wall to ensure the recessed point will fit and on which side the stud or wall trimmer is located.
- Push back the existing wall point into the wall cavity through the existing stud bracket on an angle.
- Taking the RP0x, locate the back of it over the existing wall cut-out so that the existing bracket screw holes are visible through the rear of the RP0x screw points.
- Mark the top and underside of the housing from approximately the centre of the RP0x across to the side of the stud or trimmer.
- Proceed to cut approx. 2mm above the top line towards the stud until the stud is located. Cut approx. 2mm lower than the bottom line in the same direction until the stud is located.
- Place the cut-out template provided over the wall sheeting from the located stud and across the direction of the 2 cuts and mark around the template.
- Continue cutting around the lines noticing that you are cutting around the existing bracket.
- Cut vertically down the side where the stud or trimmer is located and remove the wall sheeting.
- This will expose the existing bracket inside the wall cavity ready for removal, Pry the bracket off the stud or trimmer and discard it.
- Continue with point 4 of “How to install in new builds”.
If installing more than 1 recessed point, ensure they are located more than 50mm apart vertically and/or horizontally. Designed for 70mm and 90mm wall cavities.
- Note: Screw length MUST NOT exceed 25mm
- Warning: To be installed by a licensed electrician or technician only. All power should be switched off before installation. Matchmaster Communications Pty Ltd accepts no responsibility for any loss or damage suffered by a person or their property as a result of use misuse, or failure of these goods. In the case of any defects within this product, Matchmaster. Communications Pty Ltd’s liability would be limited to the replacement of this product.
- Australian design registration numbers: 201815617, 201815619, 201815620 and 201815621
- New Zealand design registration numbers: 425766, 425767, 425768 and 425769
- THIS IS A TEMPLATE FOR YOUR 04MM-RP01, RP02 & RP03 (168X120MM)
- 04MM-RP01, RP02 & RP03
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>