PaRMCO WM7WT02 7KG Washing Machine Instruction Manual

PaRMCO WM7WT02 7KG Washing Machine

Specifications

• Model: WM7WT02
• Washing Capacity: 7.0kg
• Standard Water Pressure: 0.03MPa~0.8MPa

Product Description

The WM7WT02 washing machine is designed to provide efficient and effective laundry cleaning for a capacity of up to 7.0kg of laundry. It operates within a standard water pressure range of 0.03MPa to 0.8MPa, ensuring optimal performance.

• Before installing the washing machine, ensure you have selected a suitable installation area with proper drainage and access to water connections. Unpack the washing machine carefully and follow the instructions to level it properly to avoid vibration during operation.
• Connect the inlet hose securely to the tap ensuring there are no leaks. Make sure the drain hose is correctly installed to prevent water spillage.
• Prior to washing, ensure the washing machine is properly plugged in and water connections are secure. Load the laundry according to the recommended capacity and select the appropriate washing program.
• Start the washing machine and monitor the operation through the control panel. Follow the washing program table for guidance on cycle selection based on your laundry needs.
• Regularly clean the cabinet, inlet filter, and drain pump filter to maintain optimal performance. Refer to the troubleshooting section for any issues that may arise during operation.

FAQ

• What should I do if the washing machine door won’t open after a wash cycle?
• If the door does not open immediately after a wash cycle, wait for a few minutes as there might be a delay in unlocking. If the issue persists, refer to the troubleshooting section in the manual for further guidance.
• How can I dispose of the washing machine responsibly?
• To dispose of the washing machine responsibly, do not discard it with household waste. Contact your retailer for safe recycling options or use designated collection systems to promote environmental sustainability.

The Warranty

• Subject to the terms and conditions contained within this warranty, if the product is not of Acceptable Quality (as defined in the Consumer Guarantees Act) within 2 years of the date of original purchase, then Parmco Sales undertakes to repair or, at it’s sole discretion, replace the product.
• The warranty does not cover the costs of transport, mileage or traveling time if the product is located beyond 30km of a recognized Service Agent.
• This warranty is offered as an extra benefit and does not affect other legal rights, which can not be modified or excluded by agreement.
• This warranty only applies to goods supplied and installed in the North and South Islands of New Zealand.
• The provisions of this warranty are in addition to the rights and remedies available to consumers under the Consumer Guarantees Act 1993.
• Products purchased as seconds or thirds may or may not carry a warranty. Please check with your reseller at the time of purchase for the warranty period being offered.

Please retain this Warranty card together with a receipt or other proof of purchase date when seeking service during the warranty period
Please contact Parmco at 09 573 5678 if your appliance needs servicing under warranty. Please have your model number and proof of purchase ready. Warranty repairs must be authorized by Parmco.
Subject to updates without prior notice, please visit www.parmco.co.nz for the latest version.

The Warranty is not valid

• If the product is not installed and operated under the operating instructions.
• If the product is not installed to comply with the electrical, gas, plumbing and other Regulations and Codes of Practice in New Zealand.
• If the product is operated on voltages or frequencies outside the normal range for domestic appliances in New Zealand.
• If the product is not used in normal domestic use, or if it is used in a business as defined in the Consumer Guarantees Act.
• If any serial number has been removed or defaced.
• If proof of date of purchase is not supplied, except at the sole discretion of Parmco Sales. Proof of purchase can be for the product itself, or if installed with a kitchen or house then proof of purchase can be from a Parmco reseller of products supplied by Parmco.
• If the products are purchased in a second-hand condition from other parties (including but not limited to TradeMe, Sella, etc.)

Liability under this warranty will not be accepted for

• Wear and tear from normal domestic use.
• Damage in transport.
• Damage caused to the product by neglect, abuse, negligence, wilful act or misuse.
• Any costs associated with the repair, replacement, removal or reinstallation of products installed in a damaged condition.
• Any defect caused by accident, misuse, neglect, tampering with, or unauthorized modifications of the appliance or any attempt at internal adjustment or repair by any person other than an Authorised Service Agent. Service calls that relate principally to the following:
• Instruction on how to use the product.
• Repair or replacement of house fuses, electrical wiring, gas fitting, or plumbing.
• Wear and tear caused by normal use of the product.
• Normal or scheduled maintenance including blocked filters or ducting. Consumable items such as light bulbs.
• Any damage to hobs caused by spills when cooking.
• Any breakage or damage of glass items.
• Any damage caused by non-recommended product used for cleaning, maintaining, lubricating or similar.
• Any aspect relating to the installation of the product, or damage caused during installation including blocked access for repair.
• Any third party (including reseller) or consequential loss or damage (direct or indirect) however arising.

Dear Valued Customer,

• Thank you and congratulations on purchasing your new Parmco appliance.
• All Parmco products are made to the highest quality and design standards. We are sure you will enjoy your new appliance.
• As a note, please read through these instructions carefully. These will assist you in gaining a complete understanding of the functions and features offered by your appliance. Please take special note of all detailed technical information and installation instructions. You must follow these instructions to ensure the safety and reliability of this appliance. Furthermore, not using appropriate personnel to install this appliance may affect any future warranty claims lodged, so please check with Parmco
• Appliances before any installation is carried out.
• We hope you enjoy your new appliance. If you would like to find out more about this product or any other products in Parmco’s extensive range, visit us online at www.parmco.co.nz.

SAFETY INSTRUCTIONS

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury or loss of life.

• This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have
  been given supervision or instruction concerning the use of
  the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.

• The new hose sets supplied with the appliance are to be used and the old hose sets should not be reused.

• The openings must not be obstructed by a carpet.

• This appliance is intended to be used in household and similar applications such as:

  • staff kitchen areas in shops, offices, and other working environments;
  • farm houses;
  • by clients in hotels, motels, and other residential-type environments;
  • bed and breakfast type environments;
  • areas for communal use in blocks of flats or in launderettes.

Explanation of the symbols

Warning!
This combination of symbol and signal words indicates a potentially dangerous situation that may result in death or serious injuries unless it’s avoided.

Caution!
This combination of symbol and signal words indicates a potentially dangerous situation that may result in slight or minor injuries or damage to property and the environment.

Note!
This combination of symbol and signal words indicates a potentially dangerous situation that may result in slight or minor injuries.

Warning!

The electric shock!

• This appliance is for indoor use only.
• Do not put the washing machine at humid place.
• Hands shall not be inserted into the running spin-dry tub.
• If the spin-dry tub does not stop within 15 seconds after opening the cover, please stop using the machine and have it repaired.
• Before any maintenance of the device, unplug the appliance from the mains.
• Always unplug the machine and turn off the water supply after use. The max. inlet water pressure, in pascals. The min. inlet water pressure, in pascals.
• To ensure your safety, a power plug must be inserted into an earthed three-pole socket. Check carefully and make sure that your socket is properly and reliably earthed.
• Make sure that the water and electrical devices are connected by a qualified technician under the manufacturer’s instructions and local safety regulations.

Risk to children!

• EN countries: the appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
• Animals and children may climb into the machine. Check the machine before every operation.
• Young children should be supervised that they do not play with the appliance.
• The machine may be very hot during the operation. Keep kids and pets far away from the machine during the operation very wet rooms as well as in the rooms with explosive or caustic gas.
• Remove all packages before using the appliance. Otherwise, serious damage may result.
• The washing machine with a single inlet valve only can be connected to the cold water supply. The product with double inlet valves should be correctly connected to the hot water and cold water supply.
• Plug must be accessible after installation.

Risk of explosion!

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances( such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) This may result in fire or explosion.
• Before hand thoroughly rinse items of washing by hand.

Caution

Installing the product!

• This washing machine is for indoor use only.
• It isn’t intended to be built-in using.
• The openings must not be obstructed by a carpet.
• Washing machines shall not be installed in bathrooms or very wet rooms as well as in rooms with explosive or caustic gases.
• Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result.
• The washing machine with a single inlet valve only can be connected to the cold water supply. The product with double inlet valves should be correctly connected to the hot water and cold water supply.
• Plug must be accessible after installation.
• Do not wash, spin, or dry water-proof seats, down-filled coat, mats, or clothing. Do not wash thick, hard mats even if the washer mark is on the care label. This may result in injury or damage to the washer, walls, floor, or clothing due to abnormal vibrations.

Risk of damaging appliance!

• Your product is only for home use and is only designed for textiles suitable for machine washing.
• Do not climb up and sit on top cover of the machine.
• Do not lean against the machine door.
• Cautions during handling machine:

1. Transport bolts shall be reinstalled to the machine by a specialized person.
2. The accumulated water shall be drained out of the machine.
3.  Handle the machine carefully. Never hold each protruded part on the machine while lifting. The machine door can not be used as the handle during the conveyance.
4. This appliance is heavy. Transport with care.

• Please do not close the door with excessive force.
• It is forbidden to wash carpets.

Operating the appliance!

• Before washing the clothes at the first time, the product shall be operated in one round of the whole procedure without the clothes inside.
• Flammable and explosive or toxic solvents are forbidden. Gasoline and alcohol etc. Shall not be used as detergents. Please only select the detergents suitable for machine washing, especially for drums.
• Make sure that all pockets are emptied. Sharp and rigid items such as coins, brooches, nails, screws or stones, etc. may cause serious damage to this machine.
• Please check whether the water inside the drum has been drained before opening its door. Please do not open the door if there is any water visible.
• Be careful of burning when the product drains hot washing water.
• Never refill the water by hand during washing.
• After the program is completed, Please wait for two minutes to open the door.

Packaging/Old appliance

This marking indicates that this product should not be disposed of with other household wastes throughout the EU.To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the collection systems or contact the retailer where the product was purchased. They return and can take this product for environmentally safe recycling.

INSTALLATION

Product description

Note!

The product line chart is for reference only, please refer to real product as standard.

Accessories

Note!

Note: If the drain hose is already installed on the machine, then there is no spring clamper and drain hose in the accessories.

Installation area

Warning!

• Stability is important to prevent the product from wandering!

• Make sure that the product does not stand on the power cord.

• Before installing the machine, the location characterized as follows shall be selected:

1. Rigid, dry, and level surface
2. Avoid direct sunlight
3. Sufficient ventilation
4. Room temperature is above 0 C
5. Keep far away from the heat resources such as coal or gas.

Unpacking the washing machine

Warning!

Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
There is a risk of suffocation! Keep all packaging well away from children.

1. Remove the cardboard box and styrofoam packing.
2. Lift the washing machine and remove the base packing.
3. Remove the tape securing the power supply cord and drain hose.
4. Remove the inlet hose from the drum.

The installation of drain hose

Warning

• Do not kink or protract the drain hose.
• Position the drain hose properly, otherwise, damage might result of water leakage.
• If the drain hose is too long, do not force it into the washing machine as it will cause abnormal noises.

There are two ways to place the end of the drain hose:

1. For lower drain system
2. For the upper drain system

Levelling the washing machine

Warning!

The lock nuts on all four feet must be screwed tightly against the housing.

1. Check if the legs are closely attached to the cabinet. If not, please turn them to their original positions and tighten the nuts.
2. Check the alignment of the product with a spirit level and if required, correct it.
3. Loosen the lock nut and turn the feet until it close contact with the floor.
4. After being locked properly, press four corners again to make sure that they have been adjusted properly.

Selection of tap

• Please select the appropriate tap.

Connection of inlet hose, tap, and washing machine

Connection between ordinary tap and inlet hose.

1. Loosen clamp nut to show 5mm thread
2. Loosen four bolts
3. Set connecting base on tap and tighten bolts evenly
4. Tighten clamp nut
5. Press slide bushing, insert inlet hose into connecting bas
6. Connection finished
7. After connection and installation, check if there is water leakage

Connection between screw tap and inlet hose

• Tap with threads and inlet hose
• Special tap for washing machine

Warning!

• To prevent leakage or water damage, follow the instructions in this chapter
• Do not kink, crush, modify, or sever water inlet hose.

OPERATIONS

Preparation before washing

Caution!

• Before washing, please make sure it’s installed properly.
• Before washing it at the first time, the washing machine shall be operated in one round of the whole procedure without clothes in as follows.

Washing

Note!

• If default is selected, steps 2, and 3 can be skipped.

After washing

• The buzzer will beep after washing is finished and the power supply will be cut off automatically. Then unload the laundry.

Washing matters needing attention

• The working condition of the washer should be(0-40)℃. If used under 0℃, the inlet valve and draining system may be damaged. If the machine is placed under a condition of 0℃or less, then it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose are not frozen before use.
• Please check the labels and the explanation of using detergent before wash. Use non-foaming or less-foaming detergent suitable for machine washing properly.

Warning!

• When washing single clothes, it may easily cause great eccentricity and give alarm due to great unbalance. Therefore it is suggested to add one or two more clothes to be washed together so that draining can be done smoothly.
• Don’t washing the clothes with kerosene, gasoline, alcohol and other flammable materials.

The usage of detergent and washing powder

• As for the agglomerated or ropy detergent or additive, before they are poured into the detergent box, it is suggested to use some water for dilution to prevent the inlet of the detergent box from being blocked and overflowing while filling water.
• Please choose a suitable type of detergent for the various washing temperatures to get the best washing performance with less water and energy consumption.

Control panel

Note!

• The chart is for reference only, Please refer to the real product as standard.

1. On/Off
   The product is switched on or off.

2. Start/Pause
   Press the button to start or pause the washing cycle.

3. Program
   Available according to the laundry type.

4. Option
   This allows you to select an additional function and will light when selected.

5. Display
   The display shows the settings, estimated time remaining, options, and status messages for your washer. The display will remain on through the cycle.

When LED flashes it means the time that is delayed to start the machine. When LED lighting it means the program time that remaining.

Only washers having these functions.

• Water level
  Select water level according to clothing categories, degree of soiling, and washing habits of customers

• Rinse
  Rinsing times settings can be selectable

• Function
  A combination of soaking, washing, rinsing, and spinning lights is available

• Temp.
  Press the button to regulate the Hot, warm, and cold water for washing.

Delay

1. Select a program
2. Press the Delay button to choose the time
3. Press [Start/Pause] to commence the delay operation

Press the [Delay] button until the Delay light is off . It should be pressed before starting the program. If the program already started, should press the [On/Off] button to reset the program.

Caution!
If there is any break in the power supply while the machine is operating, a special memory stores the selected program and when the power is restarted.

Caution!

• Press the two buttons also to release the function.
• The “ Child Lock” will lock all buttons except [ On/Off ].

Personalized setting of washing program

• Customers can select a washing program according to actual demand, and set rinsing times, water volume and appointment time

Operations of the washing process

• customers can set a single process or combinations of washing、rinsing and spinning freely according to demand. Detailed operations as follows for different models:

One Touch Smart Wash

Spin

Wash +Rinse+ Spin

Note: Other process combinations are just like the above.

Washing Program Table

Programs are available according to the laundry type.
Only washers having these function

Program

Jeans| Suitable to wash Jeans stained/wearable clothes.
Quick 15′| Suitable to wash light-stained clothes and clothes in summer.
Soft| the tempo is soft, with slow washing and spinning speed, to make the lightest wear and deformation.
Mix| Suitable to wash cotton, linen, flax. jute clothes
Normal (Standard)| Standard fabric washing program, suitable to wash ramie cotton fabric. Wash for once, rinsing twice, the spin time is a little long.
Strong| The wash time is longer, and the stream is stronger, so the washing effect is better.
Heavy| Suitable to wash heavy stained/wearable clothes.
FCS| Start up Fast Clean System: Power on, select “Normal”,” Heavy”, “Mix”,”Strong”, and “Jeans” programs, then press the FCS button.

then press the “Start/Pause” button, FCS function starts up. The relative figures will be shown after the FCS function starts up.

Cancellation of FCS function: when the FCS function is selected, The function can be canceled by pressing the FCS button or powering off.

Fuzzy weighting| The washing machine will select the water level automatically according to the load weight.

1.  When there’s water in the tub, this function is not available;

2.  Before pressing the [Start/Pause] button, if the consumer selects the water level, there will be no fuzzy weighting function;

3.  After pressing the [Start/Pause] button, the washing machine will run the fuzzy weighting function. Consumers can also select the water level to set the water level as needed.

MAINTENANCE

Cleaning and care

Warning!

• Before your maintenance starts, please unplug the machine and close the tap.

Cleaning the cabinet
Proper maintenance on the washing machine can extend its working life. The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use the wet cloth to wipe it off immediately. No sharp items are allowed.

Note!

• Formic acid and its diluted solvents or equivalent are forbidden, such as solvents or chemical products, etc.

Cleaning the inlet filter

Note!

• The inlet filter must be cleaned if there is less water.

Washing the filter in the washing machine

1. Screw off the inlet pipe from the backside of the machine.
2. Pull out the filter with long nose pliers and reinstall it back after being washed.
3. Use the brush to clean the filter.
4. Reconnect the inlet pipe.

Lint filter clean

1. There is a built-in lint filter in your washer. It can help to collect lint during the washing cycle.
2. It is suggested to clean the lint filter every 10 cycles.
3. Take it out and clean the filter with water.

Then place it back into the washer.

Note!

Only washers having these function

Cleaning drain pump filter

• Only washers having these function

Warning

• Be careful of the hot water!
• Allow the detergent solution to cool down.
• Unplug the machine to avoid electrical shock before washing.
• A drain pump filter can filter the yarns and small foreign matter from the washing.
• Clean the filter periodically to ensure the normal operation of the washing machine.

1. Drain the water out of the pump, under which use a container to collect.
2. Open the filter by turning to the counterclockwise
3. Remove extraneous matter
4. Clean the filter.
5. Restore it and adjust the convex place to align at the pump hole.
6. Tighten the pump cover clockwise.

Caution

• Make sure that the valve cap and emergency drain hose are reinstalled properly, cap plates should be inserted aligning to hole plates otherwise water may leak;
• Some machines don’t have emergency drain hose, so step 2 and step 3 can be skipped.
• Rotate the lower cover cap directly to make water run into the basin.
• When the appliance is in use and depending on the program selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened.

Troubleshooting

• The start of the appliance does not work or it stops during operation.
• First try to find a solution to the problem, If not, contact the service center.

voltage is too low.

If the water amount reaches the required water level. (The washer will not work if the water amount does not reach the required water level)

If it is set to “Delay” washing mode. (It will only start to work until the reservation time is reached)

No water flows in| If the power is off or the fuse is burned out.

If the water supply is cut off or the water pressure is too low.

If the inlet hose is properly connected and the water tap is opened. If the filtering screen of the inlet valve is blocked by dirt.

If the coil of the inlet valve is damaged. (The slight electromagnetic sound is a normal phenomenon when the inlet valve is switched on)

If the “Start / Pause” button is pressed after the power switch is pressed.

Abnormal draining| If the water drain hose is placed very high.

If the end of the water drain hose is sealed in the pond.

If the internal rubber ring of the drain valve is blocked by dirt.

Abnormal spin| If the door lid is closed.

If all clothing is piled largely at one side of the barrel or the clothing is excessively placed.

If the washer is not placed in stable condition or it is placed in an inclination state. (The ground is not flat).

If the motor belt is loosened.

not.
E2| The alarm for the water drain has not been finished.| Check the water level sensor and drain pump.
E3| Alarm for lid not closed before wash and spin.| Close the lid, Press the “Start” button
E4| The alarm for washing stays on one side.| Manually balance clothes in the barrel with your hands.
EXX| Others| Please try again first, call up the service line if there are still troubles

Note

After the check, activate the appliance. If the problem occurs or the display shows other alarm codes again, contact the service.

Technical Information

Standard Water Pressure 0.03MPa~0.8MPa

Model| Washing Capacity| Dimension (WDHmm)| Net Weight| Rated Power| Power Supply
---|---|---|---|---|---
WM7WT02| 7.0kg| 550x570x940| 38kg| 550W| 220-240V~,50Hz

Energy efficiency test program

• During the “Normal” Washing program, the water level is 8 levels, wash Temp. is warm.

Subject to updates without prior notice, please visit www.parmco.co.nz for the latest version.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>