EMAUX SSC-Nano Series Residential Salt Chlorinators User Manual
- July 25, 2024
- Emaux
Table of Contents
EMAUX SSC-Nano Series Residential Salt Chlorinators User Manual
WARNINGS
WARNING:
This product should be installed and repaired by a technician who is
qualified in the installation and maintenance of pool/spa products.
Please read this manual before installing the product. The instructions in
this manual can be followed exactly. Disconnect electrical power before
removing the cover for servicing unit. Replace all screws and covers before
reconnecting the unit to electric power. Incorrect installation and/or
operation can cause serious injury, property damage, or death. To reduce the
risk of injury, do not permit children to use this product.
Improper installation and/or operation will void the warranty.
PRODUCT INTRODUCTION
SSCnano is an innovative inline salt chlorinator that seamlessly synchronizes with the pump. With its preset timer offering flexible options and 4 chlorine production modes, SSCnano provides complete control over the chlorination process. Enjoy the benefits of long cell life and reduced chemical usage, thanks to its efficient and environmentally friendly design. Compact and user- friendly, SSCnano revolutionizes the experience of chlorine production.
Salt chlorination is a method of sanitizing swimming pools with chlorine
generated by electrolysis.
The electrolysis is achieved by passing the salt water solution through a weak
electric charge in an electrolytic cell, which converts sodium chloride (salt)
in the water into chlorine gas. The gas is dissolved in the water and becomes
sodium hypochlorite (liquid chlorine).
SPECIFICATIONS
Code| Model| Input Voltage/ Frequency| Salt Level| Cell
Production Rate| Maximum Working Pressure| Cell Connections|
Working Temperature| Min. Flow| Max Pool Volume
---|---|---|---|---|---|---|---|---|---
9130045| SSCnano4| 110 – 240V/50-60 Hz| 3500ppm| 4g/hr| 2.5 bar| 1.5”/ 50mm
and 32mm&38mm union| 10-45°C| 3 m³/hr| 20m³
9130046| SSCnano6| 6g/hr| 30m³
9130047| SSCnano8| 8g/hr| 40m³
9130048| SSCnano10| 10g/hr| 50m³
DIMENSION(mm)
ACCESSORIES
32mm(1¼”) & 38mm(1½”) Flexi hose connector
50mm (1½”) union
Mounting Stand
- 32mm(1¼”) & 38mm(1½”) Flexi hose connector and 50mm (1½”) union installation, please refer to Part 3, Installation & Operation.
- The mounting stand is allowed the SSCnano.If place stand on the floor or wall mount.
[Fig.1] Stand and Wall Mount
INSTALLATION & OPERATION
Check the pool system regularly and make sure the parameters are within the range:
| Parameter | Target range |
|---|---|
| Salinity | 3,000 to 4,000 ppm |
| pH level | 7.2 to 7.4 |
| Water temperature | 10 – 45°C |
| Flow rate | 3 to 10 mᶾ/h |
INSTALLATION
The SSCnano.If has an arrow mark on its body [Fig.2] showing the water
flow direction. It is designed to operate with water flow rates between 3-10
mᶾ/h.
Please refer to the pipe manufacturer specifications for recommended maximum
flow rate. It is a must to use a bypass loop with flow control valve if the
flow rate is over 8 mᶾ/h. [Fig.3] showing the general installation.
Adding a valve before and after SSCnano.If to make sure the isolation between
SSCnano.If and the facilitate when maintenance.
CONNECT WITH 50MM (1½”) UNION
SSCnano.If can be installed either horizontal or vertical. The union is
designed for imperial 1½” pipe and metric 50mm pipe.
Pipes are required gluing to fix.
CONNECT WITH THE 32MM(1¼”) & 38MM(1½”) FLEXI HOSE CONNECTOR
The 32mm(1¼”) & 38mm(1½”) Flexi hose connector can let the SSCnano.If use with
flexible pipes, shown as [Fig.6].
OPERATION2
ON / OFF
CHLORINE PERCENTAGE
Optimize the chlorine percentage, to suit pool size/ temperature.
If the pool size is smaller than the max pool size of the SSCnano.If, lower
the chlorine percentage proportionally. (e.g. Using SSCnano4 for a 10m³ pool,
press twice to 50% of the max chlorine percentage rate.)
Operating during winter:
The lower the water’s temperature, the lower the salt water’s conductivity
will be. This in turn will cause the SSCnano.If to work much harder than
normal to produce chlorine. Algae and bacteria don’t grow well in cold
environments. Thus, very little chlorine is needed, simply adjust the chlorine
percentage to an ideal rate.
During winter (e.g. temperature drops below 16℃ ), you can reduce to 25 % of the max chlorine percentage to minimize chlorination for your pool.
Low-temperature protection:
When the water temperature is below 10℃, SSCnano.If will stop functioning. (
, Nalco light will flash, refer to Part 4, Troubleshooting). This feature
prolongs the service life of the cell.
TIMER
The timer setting can synchronize with the expected operation time for energy saving. (e.g. To set the timer ON at 9:00 and off at 17:00. When it is 9:00 a.m., press twice to set the timer of SSCnano.If to 8 hours. It will stop running at 5:00 p.m. and function again at 9:00 a.m. the next morning.)
Note:
- All setting will be saved when press ON/OFF to power off the SSCnano.If.
- Power cut SSCnano.If will reset all settings to factory default.
MEMORY MODE
This function is for connecting the SSCnano.If to an automation system
device. The SSCnano.If will start chlorine generation once powered up. The
chlorine percentage setting will be saved after power down. (e.g. The chlorine
percentage of the SSCnano.If was set to 50%. The setting will be kept if the
power is cut and turned back on.)
Note: The set time will not be saved and reset to default when power down.
To enter memory mode:
During OFF stage, press and hold for 5 seconds to enter the memory mode. (The
light will flash three times. It will flash once every 30 seconds if the
SSCnano.If is running in memory mode.)
To cancel memory mode:
During ON stage, press and hold for 5 seconds to cancel the memory mode. (The
light will flash three times after canceling the mode and then stop.)
TROUBLESHOOTING
| LIGHT FLASH CONTINUOUSLY | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Low salinity level. Salinity below 2500ppm, causing the production rate of | ||
| chlorine is being reduced. | The normal operating range is 3,000 to 4,000 ppm. |
Add salt to pool to achieve 3500 ppm to ensure. Once the correct level has
been reached. The chlorinator should operate normally.
| No flow/ Flow rate too small/ error in flow sensor| The normal operating
flow rate range is between 3 to 10 mᶾ/h. Make sure the flow rate is
sufficient. The bypass is proving enough water to the cell and the valves are
correctly set. If all the above were confirmed, the flow sensor might have
fatal error, contact customer support for a replacement.
| Water temperature is not within the operating range or error in temperature
sensor| Make sure the temperature is between 10 to 45℃.If the above were
confirmed, the temperature sensor might have a fatal error, contact customer
support for a replacement.
| Incorrect input voltage| Make sure the unit is connected to the SSCnano.If
paired adaptor.
| Cell lifetime ran out| Check the wiring connection, and restart SSCnano.If
all the lights still flash, please contact customer support for a replacement.
No function| Wiring issues| Make sure the power supply is connected and input
the correct voltage [110-240V, 50-60Hz].If it still having no function, please
contact customer support for a replacement.
SPARE PARTS LIST
| Key No. | Part No. | Description | QTY |
|---|---|---|---|
| 1 | 530135108 | Electrolytic cell nut | 1 |
| 2 | E1330069 | SSCnano4 Electrolytic cell （4 grams) | 1 |
| E1330070 | SSCnano6 Electrolytic cell（6 grams) | 1 | |
| E1330071 | SSCnano8 Electrolytic cell（8 grams) | 1 | |
| E1330072 | SSCnano10 Electrolytic cell（10 grams) | 1 | |
| 3 | 1062510186 | SSCnano.If PCB | 1 |
| 4 | 111010013 | SSCnano.If O-Ring | 1 |
| 5 | 111040010 | D116.6X1.5 O-Ring | 1 |
| 6 | 5300410081 | Electrolyze housing | 1 |
| 7 | 111202472 | O-Ring D70 x d60 x 6 | 2 |
| 8 | 430170991 | 2.0″ Union Nut (black) | 2 |
| 9 | 430300943 | 1.5″ Union | 2 |
| 10 | 111142481 | O-Ring d42x3 | 2 |
| 11 | 430091071 | 32×38 Union | 2 |
| 12 | 5203410081 | Stand | 2 |
| 13 | 5203410083 | Mounting Stand Base | 1 |
| 14 | 106090062 | DC power supply（4 & 6 grams) | 1 |
| 106090063 | DC power supply（8 grams) | 1 | |
| 106090064 | DC power supply（10 grams) | 1 |
TERMS OF THE WARRANTY
As original purchaser of this equipment have purchased from Emmaus Water Technology Co Ltd, through Authorized International Distributor or Dealer, warrants its products free from defects in materials and workmanship under normal use during warranty period. The warranty period begins on the day ofurchase and extends only to the original purchaser. It is not transferable to anyone who subsequently purchases the product from you. It excludes all expendable parts. During the warranty period, Emmaus authorized reseller will repair or replace defective parts with new parts or, at the option of Emmaus, serviceable used parts that are equivalent or superior to new parts in performance. This Limited Warranty extends only to products purchased from Emmaus authorized reseller. This Limited Warranty does not extend to any product that has been damaged or rendered defective
(a) as a result of accident, misuse or abuse;
(b) as a result of an act of God;
(c) by operation outside the usage parameters stated herein;
(d) by the use of parts not manufactured or sold by Emaux;
(e) by modification of the product;
(f) as a result of war or terrorist attack; or
(g) as a result of service by anyone other than Emmaus authorized
reseller or authorized agent.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, EMAUX MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. EMAUX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESS LIMITED WARRANTY.
EMAUX WATER TECHNOLOGY CO., LTD ADDRESS FLAT A-D, 20/F., ΚΑΙ ΒΟ 22, 22 WING KIN ROAD, KWAI CHUNG, HONG KONG PHONE +852 28329880
YOUR PREMIER SUPPLIER
www.emauxgroup.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>