Advance BX-1 Stereo Audiophile Integrated Amplifier User Manual
- July 21, 2024
- Advance
Table of Contents
Advanced BX-1 Stereo Audiophile Integrated Amplifier User Manual
RECYCLING IN EUROPEAN UNION COUNTRIES
Disposal of your old appliance
This symbol on the product or its packaging means that your electrical and electronic equipment should be disposed of at the end of life separately from your household wastes. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or the dealer where you purchased the product.
WARNING ATTENTION
WARNING: to reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
CAUTION: To prevent the risk of electric shock, do not remove the cover
(or back); no user-serviceable parts inside. Refer servicing to qualified
service personnel.
THE LIGHTNING FLASH with magnitude to constitute a riet of Tri neurite dangerous voltage heal me is lute en do due that may I or Surfanc magnitude to constitute a risk of electric shock to persons. An appliance and cart combination should be moved with care. Before any transportation, your product must be packed correctly to avoid any damage.
IMPORTANT
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS PLUG WITH AN EXTENSION CORD,
RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
INFORMATION
THE MAIN PLUG IS USED AS THE DISCONNECT DEVICE, THE DISCONNECT DEVICE SHALL
REMAIN READILY OPERABLE.
READ INSTRUCTIONS
All the safety and operating instructions should be read before the appliance
is operated.
RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future use.
HEED WARNINGS
All warnings on the appliance and in the operating instructions should be
adhered to.
FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
WATER AND MOISTURE
The appliance should not be used near water for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
VENTILATION
The appliance should be situated so that its location or position does not
interfere with its proper ventilation. For example, the appliance should not
be situated on a bed. sofa, rug, or similar surface that may block the
ventilation openings; or, placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air through the ventilation
openings.
HEAT
The appliance should be situated away from heat sources such as radiators,
heat registers, stoves, or other appliances (including amplifiers) that
produce heat.
POWER SOURCES
The appliance should be connected to a power supply only of the type described
in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION
Precautions should be taken so that the grounding or polarization means of an
appliance are not defeated.
POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the appliance.
CLEANING
The appliance should be cleaned only as recommended by the manufacturer.
POWER LINES
An outdoor antenna should be located away from power lines.
NON-USE PERIODS
The power cord of the appliance should be unplugged from the outlet when left
unused for a long period.
OBJECT AND LIQUID ENTRY
Care should be taken so that objects do not fall and liquids are not spilled
into the enclosure through openings.
DAMAGE REQUIRING SERVICE
The appliance should be serviced by qualified service personnel when:
- The power supply cord or the plug has been damaged; or
- Objects have fallen, liquids have spilled into the appliance; or
- The appliance has been. exposed to rain: or
- The appliance does not appear to operate normally or exhibit a marked change in performance; or
- The appliance has been dropped, or the enclosure damaged.
SERVICING
The user should not attempt to service the appliance beyond that described in
the operating instructions. All other servicing should be referred to
qualified service personnel.
FRONT PANEL CONTROLS
-
STANDBY ON / OFF POWER BUTTON
Press this button to turn ON your appliance, power is supplied to your unit and it becomes operational, and the STANDBY button’s light becomes white. (The main power switch is located on the back panel and must be ON to use the STANDBY function).
When set to STANDBY OFF, the main power is cut off and the unit is no longer fully operational except for the microcontroller. The standby indicator’s light becomes red. -
SOURCE INDICATORS
Those leds indicate the selected source. -
HIGH BIAS INDICATORS
Led lights up when High Bias is ON -
PROTECTION INDICATORS
Led lights up when protection is ON -
SPEAKER A/B/A+B/OFF’INDICATORS
Led lights up when speaker A/B/A+B//OFF is selected
REAR PANEL CONNECTIONS
-
INPUTS
You can connect your stereo sources to this input. This input is suitable for any line-level source equipment such as tuners, CD players, DVDs, MP3 players, etc.
Note: This input is only for analog audio signals. It should not be connected to the digital output of a CD player or any other digital device. -
SPEAKER TERMINALS
SPEAKERS A: Connect speakers with an impedance of 4 Ohms or greater. Connect the right speaker to the terminals marked ‘R +’ and ‘R-‘ ensuring that the ‘R+’ is connected to the ‘+’ terminal on your loudspeaker and the ‘R-‘ is connected to the loudspeaker’s ‘-‘ terminal. Connect the terminals marked ‘L+’ and ‘L-‘ to the left speaker in the same way. When using both SPEAKERS A and SPEAKERS B connect speakers of impedance 8 Ohms or greater. -
SPEAKERS B: use the same method to connect the B pair.
The high-current binding post terminals can be used as a screw terminal for cables terminating in spade or pin connectors or for cables with bare wire ends. -
SPADE CONNECTORS
These should be slotted under the terminal’s screw bushing, which is then fully tightened. Ensure the connector is tightly secured and there is no danger of bare metal from spade connectors touching the back panel or another connector as this may cause damage. -
BARE WIRES AND PIN CONNECTORS
Bare wires and pin connectors should be inserted into the hole in the shaft of the terminal. Unscrew the speaker terminal’s plastic bushing until the hole in the screw shaft is revealed. Insert the pin or bare cable end into the hole and secure the cable by tightening down the terminal’s bushing. -
BANANA CONNECTORS
You also can use banana connectors on the speaker terminal. Avoid any danger of bare metal from the speaker cables touching the back panel or another connector. -
POWER CORD
-
VOLTAGE SELECTOR
-
GENERAL ON-OFF SWITCH
You need to be sure about the voltage of your country. In case you need to use your appliance in 115V, you need to change the position of the voltage and replace the fuse with the right value indicated on the rear panel. Before plugging in the amplifier, its master power switch must be in the OFF position. -
HIGH BIAS SELECTOR
- By switching the High Bias mode to ON mode, your amplifier will be similar to a Class’A amplifier for the first watts of use.
- In this mode, the temperature of your amplifier will be important, also, there must be enough clear space around the amplifier to permit a free flow of air.
-
UPDATE
For service only -
INPUT SELECTOR
By switching the balanced or unbalanced input mode to ON mode. -
TRIGGER IN
Control trigger to ON/OFF this unit by another device. -
TRIGGER OUT
Control trigger to ON/OFF other power amplifiers. -
BALANCED INPUT(XLR TERMINAL)
Connect AV controllers or control amplifiers with balanced outputs for high- quality sound.
Connector ground terminal: Chassis grounded
The pin assignments for this terminal are given above. The amplifier uses the
European-type XLR terminal. Phase is reversed when an XLR cable is connected
to the control amplifier that uses the USA-type XLR terminal. In this case,
swap pin 2 and pin 3 to set the polarity to the European type before
connecting.
REMOTE CONTROL
SPECIFICATIONS
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product, to which this
decal- ration relates, conforms with the council EMC directive 2014/30/UE, and
the LVD directive 2014/35/UE.
Design and development in France by Advance Paris Sarl
13 rue du coq gaulois – 77390 Brie Comte Robert – FRANCE
Tel. +33 (0) 160 185 900 – Fax +33 (0) 160 185 895
email: info@advance-acoustic.com
www.advance-acoustic.com
PDF:Advance BX-1 Stereo Audiophile Integrated Amplifier User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>