Capture advance R2-HD2MPEYE Camera OSD User Guide

: June 12, 2024
: Capture advance

Table of Contents

About This Document
- Purpose
- Symbol Conventions
OSD Main Menu
- Procedure
- OSD Main Menu Interface
OSD Setting
- AE
- AWB
- DAY NIGHT
- IMAGE ENHANCE
- VIDEO SETTING
- LANGUAGE
- FUNC
- RESET
- SAVE-EXIT
- EXIT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Capture advance R2-HD2MPEYE Camera OSD

About This Document

Purpose

This document describes how to use the web management system for DVR and the cameras managed by DVR

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol	Description
Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.
| Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
| Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
| Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal injury.
| Calls attention to important information, best practices and tips.
NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.

Procedure

Camera Control Using Five Buttons

If your camera has four arrow buttons and one SET button, you can use the buttons to operate the OSD main menu. Figure 1-1 shows the five buttons.

Figure 1-1 Five-button layout

Procedure

The buttons have the following functions:

SET: Press this button to open the OSD main menu or end setup.
UP/DOWN: Press the two buttons to select the upper or lower menu.
LEFT/RIGHT: Press the two buttons to select different modes.
—-End

The OSD main menu interface includes AE, AWB, DAY / NIGHT, IMAGE ENHANCE, VIDEO SETTING, LANGUAGE, FUNC, RESET, SAVE & EXIT, and EXIT as shown in Figure 1-2.

Figure 1-2 OSD main menu interface

OSD Main Menu Interface

OSD Setting

AE

AE is intended to adjust image brightness by setting parameters such as aperture, shutter, and gain. The EXPOSURE interface includes BRIGHTNESS, EXPOSURE MODE.

Procedure

Step 1 Press the UP or DOWN button to select AE.
Step 2 Press the SET button to open the EXPOSURE interface, as shown in Figure 2-1.

Figure 2-1 EXPOSURE interface

OSD Setting

Step 3 Press the UP or DOWN button to select BRIGHTNESS and press the LEFT or RIGHT button to select a brightness value. The default brightness is 16 and the setting range is 0-100.

Step 4 Press the UP or DOWN button to select EXPOSURE MODE and press the LEFT or RIGHT button to select a exposure mode.

The exposure mode includes GLOBE, and BLC.

BLC: Press the LEFT or RIGHT button to select BLC, press the LEFT or RIGHT button to adjust BLC value. The default BLC is 4 and the setting range is 0-7.
GLOBE: Press the LEFT or RIGHT button to select BLC.

Step 5 Press the UP or DOWN button to select RETURN and press the SET return to the OSD main menu interface.

AWB

White balance is intended to reproduce the actual colors of the observed scene when the illuminance and color temperature of the target object are changed. You can set WB to GRAY WORLD, MWB or PRO.

Procedure

Step 1 Press the UP or DOWN button to select AWB. Press the SET button to open the WB interface, as shown in Figure 2-2.
AWB

Figure 2-2 AWB interface

Step 2 Press the LEFT or RIGHT button to set the MODE. The options are GARY WORLD, MWB and PRO. The default mode is GRAY WORLD

When MWB mode is selected, you can set white balance parameters, as shown in Figure 2-3.

Figure 2-3 MWB interface

AWB

Press the UP or DOWN button to select RGAIN, and press the LEFT or RIGHT button to set RGAIN. The default RGAIN is 40 and the setting range is 0-127.
Press the UP or DOWN button to select BGAIN, and press the LEFT or RIGHT button to set BGAIN. The default BGAIN is 30 and the setting range is 0-127.

Step 3 Press the UP or DOWN button to select RETURN, and press the SET button to return to the OSD main menu interface.

DAY NIGHT

You can set Day-Night to MONO, COLOR, AUTO, or EXT.

Procedure

Step 1 Press the UP or DOWN button to select Day-Night. Press the SET button to open the Day /Night interface, as shown in Figure 2-4.

Figure 2-4 DAY/NIGHT interface

Day Night

Step 2 Press the LEFT or RIGHT button to set the Mode.
Step 3 Press the UP or DOWN button to select SMART IR to close or open.
Step 4 Press the UP or DOWN button to select RETURN and press the SET return to the OSD main menu interface.

IMAGE ENHANCE

The Image Enhance interface includes CONTRAST, SHARPNESS, SATURATE, 3DNR and DWDR, as shown in Figure 2-5

Figure 2-5 Image enhance

Procedure

Step 1 Press the UP or DOWN button to select IMAGE ENHANCE. Press the SET button to open the IMAGE ENHANCE interface.

Step 2 Press the UP or DOWN button to select CONTRAST. Press the LEFT or RIGHT button to choose manual or auto , manual mode need press DOWN button to go next one, press the LEFT or RIGHT button set the CONTRAST value. The default contrast is 5 and the setting range is 0-10.

Step 3 Press the UP or DOWN button to select SHARPNESS. Press the LEFT or RIGHT button to choose manual or auto , manual mode need press DOWN button to go next one, press the LEFT or RIGHT button set the SHARPNESS value. The default sharpness is 10 and the setting range is 0-10.

Step 4 Press the UP or DOWN button to select SATURATE. Press the LEFT or RIGHT button to choose manual or auto , manual mode need press DOWN button to go next one, press the LEFT or RIGHT button set the SATURATE value. The default color gain is 5 and the setting range is 0-10.

Step 5 Press the UP or DOWN button to select 3DNR. Press the LEFT or RIGHT button to choose manual or auto , manual mode need press DOWN button to go next one, press the LEFT or RIGHT button set the 3DNR value. The default DNR is 0 and the setting range is 0-10.

Step 6 Press the UP or DOWN button to select DWDR. Press the LEFT or RIGHT button to choose CLOSE or OPEN.

Step 7 Press the UP or DO WN button to select RETURN and press the SET return to the OSD main menu interface.

VIDEO SETTING

The Video Setting interface includes HD and VIDEO STANDRAD.

Procedure

Step 1 Press the UP or DOWN button to select VIDEO SETTING. Press the SET button to open the VIDEO SETTING interface, as shown in Figure 2-6.

Figure 2-6 Video Setting interface

Step 2 Press the UP or DOWN button to select HD FORMAT, and press the LE FT or RIGHT button the interface will show more item APPLY & REBOOT. The options are AHD, TVI, CVB S and CVI. The default value is AHD.

Step 3 Press the UP or DOWN button to select VIDEO STANDARD and press the LEFT or RIGHT button to choose. The options are PAL, and NTSC. The default value is PAL. Switch the standard the screen will show APPLY & REBOOT. Press the SET to apply standard.

Step 4 Press the UP or DOWN button to select RETURN and press the SET return to the OSD main menu interface.

LANGUAGE

Press the UP or DOWN button to select LANGUAGE, and press the LEFT or RIGHT button to set this parameter. Supports 11 languages, English, Chinese, Traditional Chinese, Portuguese, Polish, Korean, French, Italian, Spanish, Russian, and Japanese.

FUNC

The FUNC interface includes PRIVACY and MOTION.

Procedure
Step 1 Press the UP or DOWN button to select FUNC. Press the SET button to open the FUNC interface, as shown in Figure 2-7.

Step 2 Press the UP or DOWN button to select PRIVACY, and press SET button the interface set privacy area, as shown in Figure 2-8.

Step 3 Press the UP or DOWN button to select MODE, press the LEFT or RIGHT button to select ON or OFF. The mode is on, press the UP or DOWN button to enter the areas to open the area and it will show on screen, as shown in Step 3.

Step 4 Press the LEFT or RIGHT button to select ON or OFF, and press the UP or DOWN button to set position and area of privacy area. Press the LEFT or RIGHT button to adjust value of parameters. There are four areas can be set.
Step 5 Press the UP or DOWN button to select COLOR, press the LEFT or RIGHT button to select RED, GREEN or BLUE.
Step 6 Press the UP or DOWN button to select TRANSPARENCY, press the LEFT or RIGHT button to select ON or OFF..
Step 7 Press the UP or DOWN button to select RETURN and press the SET return to the OSD FUNC interface.
Step 8 Press the UP or DOWN button to select MOTION, the method of setting motion is the same as privacy settings, as shown in Figure 2-10. Please refer to the setup steps above.

Step 9 Press the UP or DOWN button to select RETURN and press the SET return to the OSD main menu interface.

RESET

Press the UP or DOWN button to select RESET, and press the SET button to reset the camera OSD parameter.

SAVE-EXIT

Press the UP or DOWN button to select SAVE-EXIT, and press the SET button to save the OSD settings and return to the camera’s real-time video interface.

EXIT

Press the UP or DOWN button to select EXIT, and press the SET button to discard the OSD settings and return to the camera’s real-time video interface.