Velocity 1700 EK Quantum Edge Black Special Edition User Guide

Velocity 1700 EK Quantum Edge Black Special Edition

Specifications

• CPU Socket Compatibility: Intel LGA-1700
• Water Block Dimensions: 94.5mm x 61.5mm x 33.5mm
• RGB Cable Length: 500mm
• RGB LED Count: 14
• RGB Connector Standard: 3-pin (+5V, Data, Blocked, Ground)

Product Usage Instructions

Preparing the Motherboard

Before installing the water block, ensure that the motherboard is properly prepared. Follow these steps:

1. Turn off the computer and disconnect all power sources.
2. Remove the existing CPU cooler carefully.
3. Clean the CPU surface thoroughly with isopropyl alcohol to remove any old thermal paste residue.
4. Ensure the CPU socket area is free from dust and debris.

Installing the Water Block

Follow these steps to install the EK-Quantum Velocity2 D-RGB on an LGA-1700 socket:

1. Apply a small amount of the provided thermal grease on the CPU surface.
2. Align the water block with the CPU socket and gently place it on top.
3. Secure the water block using the appropriate screws provided in the box contents.

Connecting the D-RGB LED Strip

To connect the D-RGB LED strip, follow these steps:

1. Locate the D-RGB connector on the water block.
2. Connect the D-RGB LED strip to the water block following the correct orientation.
3. Secure the connection to ensure proper functionality.

FAQ

Q: What coolants are recommended for this water block?

A: EK recommends the use of EK-Cryo Fuel coolants for optimal performance. Corrosion inhibiting coolants are also recommended, especially for nickel plated water blocks.

Q: What should I do if I encounter air bubbles in the water block?

A: Make sure to thoroughly bleed air out of your water block to reach optimal performance. Tilt your system gently or use a pump to remove air bubbles.

Q: Can I use pure distilled water with this product?

A: It is not recommended to use pure distilled water. For best results, use EK-Cryo Fuel coolants as recommended by EK.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our website at www.ekwb.com for updates. Before installation of this product, please read important notice, disclosure, and warranty conditions that are printed on the back of the box.

• Before you start using this product, please follow these basic guidelines:
• Please carefully read the manual before beginning the installation process.
• The EK Fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.
• The use of corrosion inhibiting coolants is always recommended for liquid cooling systems, and mandatory for nickel plated water blocks.
• Do not use pure distilled water! For best results EK recommends the use of EK-Cryo Fuel coolants.
• Make sure to thoroughly bleed air out of your water block, or you will not reach optimal performance.

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY

This CPU liquid cooling unit is pre-assembled for use with modern Intel desktop socket type motherboards. By default (out of the box) this water block supports the following CPU sockets:

Intel LGA-1700

BOX CONTENTS

Mounting Mechanism – You may not need all the screws, mounting mechanism is universal!

WATER BLOCK DIMENSIONS

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

NICKEL PLEXI

Technical Specification

• Dimensions (L x H x W): 94.5 x 94.5 x 33 mm
• D-RGB cable length: 500 mm
• D-RGB LED count: 14
• D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground
  Position| EAN| Description| Quantity
  ---|---|---|---
  1| 104034| Top plate – plexi| 1
  2| 103951| OR Set| 1
  3| 104589| Metal plate Assembly| 1
  4| 8201N| M3x10 DIN7991 Screw| 7
  5| 104029| Jet plate| 1
  6| 104028| Coldplate (Nickel)| 1
  7| 9028| M4x14 DIN7991 Screw| 4
  8| 104586| Backplate Assembly| 1
  9| 104050| Acetal standout| 1
  10| 103952| Mylar sticker| 1
  11| 103006| LED Strip| 1
  12| 100663| EK Badge| 1

NICKEL ACETAL

COPPER ACETAL

FULL NICKEL

SATIN TITANIUM

WHITE EDITION

Technical Specification:

• Dimensions (L x H x W): 94.5 x 94.5 x 33 mm D-RGB cable length: 500 mm
• D-RGB LED count: 14
• D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground
  Position| EAN| Description| Quantity
  ---|---|---|---
  1| 104034| Top plate – plexi| 1
  2| 103951| OR Set| 1
  3| 104589| Metal plate Assembly| 1
  4| 8201N| M3x10 DIN7991 Screw| 7
  5| 104029| Jet plate| 1
  6| 104028| Coldplate (Nickel)| 1
  7| 9028| M4x14 DIN7991 Screw| 4
  8| 104586| Backplate Assembly| 1
  9| 106620| Acetal standout| 1
  10| 106621| Mylar sticker (White)| 1
  11| 103006| LED Strip| 1
  12| 100663| EK Badge| 1

LIGNUM EDITION

NICKEL GOLD

EDGE 1700 BLACK SPECIAL EDITION

EDGE 1700 SILVER SPECIAL EDITION

INSTALLING THE WATER BLOCK

• STEP 1
  Unscrew the pre-installed backplate from the backside of the CPU using an Allen Key 2.5 mm and save it for the later steps.

• STEP 2
  Before placing the water block, it is mandatory to remove the protective foil from the backside.

INSTALLING THE WATER BLOCK

• STEP 1
  Unscrew the pre-installed backplate from the backside of the CPU using an Allen Key 2.5 mm and save it for the later steps.

• STEP 2
  Before placing the water block, it is mandatory to remove the protective foil from the backside.

• STEP 3
  Position the CPU Water Block onto the Motherboard. Make sure to align the holes (as shown in the picture).
  Make sure to double check the layer of the Thermal Grease before placing the water block onto the motherboard.

• STEP 4
  After placing the water block, the stored backplate must be attached on the backside of the motherboard using Allen Key 2.5 mm (shown in the picture).
  Start fastening the backplate screws in a cross pattern. Do not tighten fully until all of the nuts are partially screwed in. The Allen Key 2.5mm must be used in a standing position! Otherwise, the mounting screws may crack during tighteening!
  EK recommends using the EK-Loop Torque Screwdriver – 0.6Nm : https://www.ekwb.com/shop/ek-loop-torque-screwdriver-0-6nm

• STEP 5
  With EK-Velocity2 series water blocks, it is mandatory to use the bottom port as the INLET. Mixing the ports may result in poor thermal performance of the water block.
  Tighten the fittings in clockwise direction until the gasket underneath is compressed.
  The installation of the Velocity2 water block is now complete.

CONNECTING THE D-RGB LED STRIP

• STEP 1
  Plug the 3 Pin connector from the water block’s D-RGB LED light to the DRGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, empty, Ground.
  Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard. If you put the LED Diode to the 12V RGB HEADER you can damage the LEDs. Failure to do so will damage your motherboard or LED strip.

SUPPORT AND SERVICE

• In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/
• For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.
• Include the EAN number with quantity in your request. Mounting Mechanism EAN can be found under “BOX CONTENTS”
• Thermal pads are readily available in the EK shop

SOCIAL MEDIA

Documents / Resources

| Velocity 1700 EK Quantum Edge Black Special Edition [pdf] User Guide
1700 EK Quantum Edge Black Special Edition, 1700, EK Quantum Edge Black Special Edition, Edge Black Special Edition, Black Special Edition, Special Edition
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>