saxby lighting G2521313 Amalfi Twin Spotlight Instruction Manual

saxby lighting G2521313 Amalfi Twin Spotlight

Product Information

Specifications

• Voltage: 240V 50Hz a.c.
• Lamp: 2 x 50W GU10 Halogen
• IP rating: 20

Product Usage Instructions

• Commissioning
  Thank you for purchasing the Amalfi Twin Spotlight. To ensure safe and satisfactory operation, please follow the instructions carefully.

• Fitting/Replacing Bulbs
  When fitting or replacing bulbs, make sure to use 50W GU10 Mains Halogen bulbs. Clean the spotlight with a soft dry cloth, avoiding solvents or abrasive cleaners that could damage the finish.

• Recycling Advice
  Dispose of waste electrical products properly by recycling where facilities exist. Contact your Local Authority or retailer for guidance on recycling.

• Safety Information
  For your safety, always switch off the power supply before changing lightbulbs or cleaning the spotlight. Remember to earth the product as it is a Class 1 unit.

• Installation
  Before installing the new product, remove the existing fittings completely. Take note of wire positions. Spotlights should be positioned at least 0.5 meters (50cm) away from the illuminated surface.

• Waste Electrical Products
  Recycle waste electrical products and do not dispose of them with household waste. Check with local authorities for proper disposal methods.

FAQ

Q: Can this product be dimmed?

A: Yes, this product is suitable for dimming when used with a dimmable lamp. Verify dimming compatibility with the lamp manufacturer before use.

Q: What type of bulbs should be used?

A: Use the correct type and wattage of bulbs, specifically 50W GU10 Mains Halogen bulbs. Exceeding the wattage can damage the product.

Q: How should I dispose of used bulbs?

A: Always switch off the mains before changing a bulb. Allow the old bulb to cool down before handling and dispose of it carefully and responsibly.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.

Models

Amalfi Twin Spotlight

• G2521313
• 43278
• 43282
• AC46980
• 60999

Warning

This is a Class 1 product and must be earthed.

• Please read these instructions carefully before commencing any work.
• This unit must be fitted by a competent and qualified electrician.
• Install by IEE Wiring regulations and current Building Regulations.
• To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
• This light fitting should be connected to a fused circuit.
• If replacing an existing fitting, make a careful note of the connections.
• Always use the correct type and wattage bulb. Exceeding the bulb wattage will damage the product.
• When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully and responsibly.
• This product is suitable for dimming when used in conjunction with a dimmable lamp. Please ensure verification of dimming abilities with the lamp manufacturer before use.
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Specification

• Voltage: 240V 50Hz a.c.
• Lamp: 2 x 50W GU10 Halogen
• IP rating: 20

Layout

• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk of being cut, trapped, or damaged.
• The main supply cable must have a minimum cross-sectional area of 1.0mm².
• This product must be mounted out of arm’s reach.
  • Spotlights give a concentrated beam of light and must not be positioned any closer than 0.5M (50cm) to the illuminated surface.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

• Undo the screws (C) holding the fixing bracket in place and set aside.
• Hold the bracket (A) in place and mark the position of the holes. Ensure that the product is level.
• Ensure the ceiling is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. Ensure there is a joist at the point of fixing to support the weight of the product.
• Fix into position.

Wiring

Having correctly identified the wiring from your existing light fitting, pull the wire through the hole and connect it to the connection block inside the product in the following way:

Check that…

• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
• When completed, ensure that there are no bare or loose strands of wire exposed, and cover all exposed areas of the connection block with 2 layers of insulation tape.

Commissioning

• Adjust the cable so it does not get snagged.
• Secure the product to the mounting bracket by locating the screws through the “L” shaped slots (C) in the ceiling cover and tightening the screws.
• Replace the fuse or circuit breaker and switch it on. Your light is now ready for use.

Fitting/replacing bulbs

• When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Do not exceed the wattage stated or use a different-shaped bulb from that indicated on the fitting.
• Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life.
• Remove the bulb by turning a quarter turn anticlockwise and pulling out.
• Push the bulb gently into the lampholder and twist a quarter turn clockwise to engage pins.
• We recommend cleaning with a soft dry cloth.
• Do not use solvents or abrasive cleaners as these could damage the finish.
• Glass parts – Wipe clean with a damp cloth. Do not use abrasive materials as these will damage the finish.

Recycling advice

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

Safety information

For your safety, always switch off the supply before changing lightbulbs, or cleaning.

References

• Saxby Lighting - Commercial and Domestic Lighting Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>