SYMA Z3pro Folding Quadcopter Drone Camera User Manual

SYMA Z3pro Folding Quadcopter Drone Camera

User Manual

Accreditation standard: GB/T26701-2011
The materials, specifications, parts and packaging mentioned in this manual are for reference purposes only. We are not responsible for any changes made to this printed material, nor are we able to inform customers of any updates or changes. Please refer to the SYMA Toys website for the latest information.

Important safety information
Thank you for purchasing this SYMA product. To ensure that you operate the aircraft correctly, please read these instructions carefully before first use and store them in a safe place for future reference.

Safety information

• Keep the smaller-sized accessories out of the reach of children.
• Keep the smaller-sized accessories out of the reach of children.
• This aircraft can move very quickly. When flying for the first time, push left joystick up slowly to prevent the aircraft from ascending too rapidly and causing damage or collisions.
• When the flight has ended, switch off the remote control before switching off the power on the aircraft.
• Do not store the battery in a hot environment (e.g. near open flames or a heating device).
• When the quadcopter is airborne, it should be kept at least 2-3m away from the pilot and other people to avoid the risk of a collision during landing.
• Children must be supervised by an adult when operating the aircraft. The aircraft should always remain within the line of sight of the pilot (or instructor).
• Do not recharge non-rechargeable batteries. When installing or changing the batteries, ensure that they are connected in the correct polarity. Do not mix old and ne\v batteries or different types of batteries.
• Do not short circuit the battery terminals
• If you do not plan to use the quadcopter for at least 1 O days, discharge the battery to 40%-50%(i.e. if the battery is fully charged, drive the quadcopter for half of the total driving time) This helps to prolong the lifespan of the battery
• Maintain a safe distance from the spinning propellers to avoid the risk of injury.
• In order to prevent interference with air traffic control systems. it is forbidden to use remote controls within a5000m radius of an airport runway (calculated from the centre of the runway). Alv1ays comply with remote control restriction orders issued by national authorities.
• You must only use the recommended transformer for this model. The transformer is not part of the model. Disconnect the model from the transformer or charger before cleaning with cleaning fluid. Regularly inspect the transformer’s wires, plug socket, outer casing and other accessories to ensure that they are not damaged. If there are any signs of damage, discontinue use immediately until the fault has been repaired.
• After use, ensure that the quadcopter and remote control are switched off and remove the batteries in the remote control.
• The packaging and this manual contain important information and should be kept in a safe place for future reference.
• Do not look directly at the laser beam.
• a reminder that the toy must be used with caution since skill is required in order to control the flight and avoid collisions with the user, objects or third parties
• precautions to be observed such as “Do not touch the rotating rotor, avoid loose clothing or hair that could be caught in the rotor.do not fly near the face”
• advice to adult supervisors to teach children how to safely fly and control the toy.
• conditions to be observed when using the toy

Repair and maintenance

• Clean the product regularly with a clean, soft cloth.
• Avoid exposing the product to direct sunlight or heat.
• Do not submerge the product in water, as this may damage the electrical components.
• Regularly inspect the propellers, motor and battery If there are any signs of damage, discontinue use immediately until the fault has been repaired.

About this product

Specifications

• Aircraft
  Weight Aircraft              Approx. 141 g
  Specifications                31 Ox307x49 mm
  Flight range                     Approx.50 m
  Flight Altitude                  Approx.50 m
  Flight time                       Approx.17 mins
  Motor                                 08
  Battery                             3.7 V, 1500 mAh
  Battery Charging time    Approx. 110 min

• Remote control
  Operating frequency  2.4 GHz
  Operating temperature  0°Cto 40″C

• Package contents
  Aircraft                            1
  Remote                            1
  Phone holder                  1
  USB charging cable       1
  Propeller                          2  (A\B)
  Propeller protector        4
  User manual                    1

Aircraft components

1. CD Propeller protector
2. Motor
3. Battery
4. Power switch
5. Propellers
6. Rear indicator
7. Front indicator

Remote control components

1. Power ON/OFF

2. Left joystick
   Keep pushing in until  trimming control finished.
   To clear all the trimming setting. keep pushing and press the power button at the same time.

3. Right joystick
   Press and hold to enter/exit headless mode. Press to change high/low speed.

4. 360°Stunt flip

5. Auto take-off and landing

Assembling the product

1. Unfold the arms in the direction
2. Fold the arms in the direction of the arrow of the arrow until the quadcopter

1. Pull out the blade decor cap.
2. Remove the screws before re-installing the blades.
3. A labeled blades fit on the A labeled motors. B-labeled blades fit on the B labeled motors. Use the screws to lighten the blades. Refer to the image

Protective Gear’s Installation Methods

1. Insert the protective gear into the arm of the drone as shown.
2. Insert the fixed rods on the protective gear into the two sockets in the arm of the drone as shown and fix them tightly.

Charging the aircraft battery

• Charge the quadcopter with the USB charging cable that came with the product.
• Using adapters with a lower rated current will result in a longer charging time
• The toy is only to be connected to Class II equipment bearing the symbol [g]
• Do not short circuit or compress the battery, as this may cause an explosion.
• Do not disassembling the battery or store it in a hot environment.
• If you do not plan to use the aircraft for at least 10 days, discharge the battery to 40%-50%. This helps to prolong the lifespan of the battery.
• Rechargeable potteries should be removed from the aircraft before charging charged.
• Rechargeable batteries should only be charged under the supervision of adults. and keep away from flammable materials.
• Exhausted batteries should be removed from the aircraft.
• Caution: Risk of explosion if battery is replaced with incorrect ones, please install the batteries according to the instructions.

Inserting the remote control batteries
To insert batteries into the remote control, batteries, open the battery cover and insert 4 x AAA alkaline batteries, ensuring that you observe the polarity markings (batteries are not included and must be purchased separately).

1. When installing the batteries, ensure that you match the + and – ends of the battery with the + and – signs on the controller.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.

Flight preparation and turning the quadcopter ON and OFF
Pairing the remote control with the quadcopter

1. Press the power button on the  remote control.
2. Press the power button on the top of the quadcopter.
3. Move the left joystick up to the  highest point.
4. Move the left joystick to the lowest ill point

After you switch on the remote control, the indicator will flash quickly to indicate that the remote control is waiting to pair with the quadcopter

Turning the quadcopter on

• Push to the top and bottom and then return to the central position.
• Push the left and right joysticks to the button inner corners for 1 second.
• For one-button take-off, press this button. The drone will automatically take off and hover.

Note

1. If the drone is flown out of range of the remote control, the indicator lights will flash slowly and the drone will land.
2. If the remote control suddenly turns off or runs out of prover during flight, the drone will automatically land. If the remote control is turned back on during this process, you will be able to regain control of the drone

Turning the quadcopter off

• Push down for 2-3 seconds.
• Push the left and right joysticks to the bottom inner corners for 1 second.
• For one-button landing, press this button. The drone will automatically land.

Using the remote control

Trimming

If the aircraft drifts forwards or backwards when it is hovering, hold the left joystick down and push the right joystick down/up until the aircraft stops drifting.

If the aircraft drifts to the left or right when it is hovering, hold the left joystick down and push the right joystick right/left until the aircraft stops drifting.

Function Introduction

Under voltage protection
A flashing light on the front and rear of the aircraft indicates that the battery level is low. When this occurs, bring the aircraft back to land.

Overcurrent protection
If the aircraft’s blades collide with another object or become stuck, the aircraft’s circuit will engage the overcurrent protection mechanism.

Place the aircraft on a level surface and move the left and right joysticks to the lower right corner for approximately 3 seconds. The indicator will flash rapidly and then stay constant to indicate that the calibration process is complete.

Briefly press the right joystick to switch between l1igh and low speed n1ode.

1. Low speed mode is enabled by default when the aircraft is switched on.
2. The remote control beeps twice when high speed mode is enabled and once when low speed mode is enabled

Once you have mastered the basic controls, you can try performing some flip manoeuvre. Start by flying the quadcopter to an altitude of at least 3 m. Then hold down the button on the top-right corner of the remote control (flip button) and push the right joystick all the way up/down/left/right to flip the aircraft forward/back1sards/left/right

1. When the aircraft is in standby, press the take-off button to make the aircraft take off automatically and hover at a height of App. 1.5 m.

2. When the quadcopter is in the air, press the one-touch take-off/landing button to make the aircraft land automatically.

3. Define the front
   When the aircraft is powered on for the first time, the direction of the aircraft nose is straight ahead.

4. Start headless function

Headless mode
After the linking is completed, press and hold the right joystick (about 2S), the remote controller will emit a “dididi. .. ” sound, and the indicator light on the aircraft will flash slowly, indicating that it has entered the headless state; press and hold the right joystick again (about 2S) When you hear a long beep, you will exit the headless state.

In the headless state, the controller does not need to identify the position of the aircraft’s nose, but only needs to control the aircraft according to the direction of the joystick of the remote control

Define the positive direction function correction

When the aircraft collides with a headless state, if you find that the fixed head direction is deviated, you only need to re-orient the aircraft and move the left and right joysticks of the remote control to the lower left at the same time. When the indicator on the aircraft flashes slowly 3 A long light after a second indicates that the calibration is complete.

Atmospheric pressure positioning
When you release the left joystick (throttle) after ascending/descending, the quadcopter will continue to hover at the current height.

Optical flow hover function
When the drone is turned on, the drone will automatically start the optical flow positioning function when hovering in the air, and the drone will remain stationary at a certain point.

1. Achieve fixed-point accuracy of about 0.5 meters.
2. If the light is dark, the ground reflects, the height is greater than 12 meters, or the wind is above level 2,the optical flow positioning will influenced under these conditions, at this time the indicator light of the drone will be flashing three times

Rectification Procedures

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WIFI frequency band: 2410-2472MHz
RF frequency band 2410-2472MHz
Transmitter power : -4.09dBm (Max.)

Sold to EU country

• product name : [Drone]
• model number : [Z3 Pro]
• Brand name :SYMA
• Contact person : Ivan
• Tel: +86-0754-86381701

Hereby, [GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD], declares that this [aircraft ] is in compliance with Directive 2014/53/EU. The full test of the EU declaration of conformity is available at the following internet address: http://www.symatoys.com/down/declaration-of-conformity.htm I SIMPLIFIED EU DECLARATION OF CONFORMITY

Manufacturer

• Guangdong SYMA Model Aircraft Industrial Co., Ltd.
• Address: 2 West Xingye Rd, Laimei Industrial Area,
• Chenghai, Shantou, China
• Postal. Co.de: 515800
• Sales department : +86 0754 86980668
• After -sales service: +86 0754 86395095
• Fax: +86 0754 86395098
• Website : www.symatoys.com
• Email: syma@symatoys.com

The company has the right of final interpretation of this user manual.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>