tp-link Festa F54 Wireless Access Point Installation Guide

: July 17, 2024
: tp-link

Table of Contents

tp-link Festa F54 Wireless Access Point
Hardware Overview
Hardware Installation
Power Supply
Software Configuration
Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

tp-link Festa F54 Wireless Access Point

Note: Festa F54 is used as an example throughout the Guide. Images may differ from your actual product.
©2024 TP-Link 7106511101 REV1.1.0

Hardware Overview

Front Panel

LED Indicator

Solid Green: The device is initializing or working properly.
Flashing Green: The device is in an isolated state.
Flashing Yellow: The device is working abnormally.
Slowly Flashing Yellow, Green: The device is updating. Do not disconnect or power off the device.
Quickly Flashing Yellow, Green: The device is being reset to its factory default settings.

Rear Panel

RESET
With the device powered on, press and hold the button for about 5 seconds until the LED is quickly flashing yellow then green, then release the button. The device will restore to factory default settings.

ETHERNET / ETH1 (PoE)
The port is used to connect to the PoE port of a PoE adapter or a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable.*

For models with the POWER port, the Ethernet port can also be used to connect to a router or a switch for data transmission only.

ETH2
The port is used for bridging.

Some models do not have this additional Ethernet port. For details, refer to the product specifications or datasheet.

POWER
Plug one end of the provided power adapter to this port and the other end to a standard electrical wall outlet to supply power.

Some models do not provide a POWER port and power adapter. For details, refer to the product specifications or datasheet.

Hardware Installation

The AP can be ceiling-mounted or wall-mounted. Choose a mounting method according to your needs. Follow the steps below for the appropriate installation.

Option 1: Ceiling Mounting
Note: Make sure that the ceiling tile is bigger than the AP.

Remove the ceiling tile.
Place the mounting bracket in the center of the ceiling tile.
Mark positions for the screw holes and a position for the Ethernet cable hole.
Drill holes for the screws and a hole for the Ethernet cable at the marked positions.
Secure the mounting bracket to the ceiling tile using pan-head screws, washers and wing nuts, as shown on the left.
Feed the Ethernet cable through the hole and set the ceiling tile back into place.
Connect the Ethernet cable to the ETHERNET / ETH1 (PoE) port. Attach the AP to the mounting bracket by aligning the arrow mark on the AP with the arrow mark on the mounting bracket, then rotate the AP until it locks into place, as shown on the left.

Option 2: Wall Mounting
Note: For security reasons, it is not recommended to install the AP with the louver downward.

If your Ethernet cable feeds through the wall, you can position the mounting bracket to make the cable through the fixing hole. Mark positions for the screw holes and drill holes at the marked positions.
Insert the plastic wall anchors into the holes.
Secure the mounting bracket to the wall by driving the self-tapping screws into the anchors. Make sure that the shoulders of the mounting bracket are on the outside.
Connect the Ethernet cable to the ETHERNET / ETH1 (PoE) port on the AP.
Attach the ^ to the mounting bracket by aligning the arrow mark on the AP with the arrow mark on the mounting bracket, then rotate the AP until it locks into place, as shown on the left.

Tip To remove the AP from the mounting bracket, insert a paper clip in the Security Slot to release the Locking Tab and rotate the AP until it is detached from the mounting bracket, as shown below.

Power Supply

The AP can be powered via a power adapter, a PoE adapter, or a PSE device (such as a PoE switch) which complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) of IEC 62368-1.
Option 1: Via PoE Switch

Connect an Ethernet cable from the PoE switch to the ETHERNET / ETH1 (PoE) port.

Option 2: Via PoE Adapter
Note: Some models do not support passive PoE power supply. For details, refer to the product specifications or datasheet.

Connect the Ethernet cable from the ETHERNET / ETH1 (PoE) port of the AP device to the PoE adapter’s PoE port.
Connect an Ethernet cable from your LAN to the PoE adapter’s LAN port.
Connect the power cord to the adapter’s power socket. Connect the other end of the power cord to a

Option 3: Via Power Adapter
Note: Some models do not provide a POWER port and power adapter. For details, refer to the product specifications or datasheet.

Plug one end of the provided power adapter to the POWER port of the AP and the other end to a standard electrical wall outlet.

Software Configuration

You can easily configure and manage Festa APs via the Festa Cloud-Based Controller.

Option 1: Via Web Browser

Make sure that your management device can access the internet.
Launch a web browser and enter https://festa.tplinkcloud.com in the address bar. Log in with your TP-Link ID.
https://festa.tplinkcloud.com
Click + Add Controller, then you will see you have successfully registered for a Cloud-Based Controller and the controller has been added to the controller list.
Click Set Up Now, click Config New Setup and follow the step-by-step instructions to complete the configuration wizard of the controller.
On the controller’s management page, go to Devices, click + Add Devices and follow the step-by-step instructions to adopt Festa devices.
Now you can configure and manage Festa devices on the controller.

Via Festa App

Download and install the Festa App from App Store or Google Play.
Launch the Festa App and log in with your TP-Link ID.
Tap + on the upper right corner, then you will see you have successfully registered for a Cloud-Based Controller and the controller has been added to the controller list.
Tap Confirm, tap Let’s Get Started and follow the step-by-step instructions to complete the configuration wizard of the controller.
On the controller’s management page, go to Devices, click + on the upper right corner, and follow the step-by-step instructions to adopt Festa devices.
Now you can configure and manage Festa devices via the Festa App.

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use the device where wireless devices are not allowed.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.

EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.
The original EU Declaration of Conformity may be found at https://www.tp- link.com/en/support/ce/

UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca/

For detailed configurations, refer to the User Guide of the controller. The guide can be found on the download center of our official website: https://www.tp-link.com/support/download/?type=smb

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com/business to join TP- Link Community.
For technical support, the user guide and other information, please visit https://www.tp-link.com/support/?type=smb, or simply scan the QR code.