BEUTURAL 1-MR08US04 Mini Steam Iron Instruction Manual

BEUTURAL 1-MR08US04 Mini Steam Iron

1 by one Products Inc. 1230 E Belmont Street, Ontario, CA, USA 91761 Customer Service: +1 909-391-3888 www.1bvonebros.com

Introduction

Thank you for purchasing BEAL/TURAL Travel Steam Iron. This instruction manual contains important information about safety, usage, and disposal. Use the product as described and keep this manual for future reference. If you sell this steamer or pass it on, also give this manual to the new owner.

Safety Instructions

READ ALL INSTRUCTIONS BEFORE USE AND RETAIN FOR FUTURE REFERENCE

• This appliance is for light or occasional indoor/household use only. This iron is not intended for professional laundry services.
• The iron should always be turned to the minimum setting before plugging or unplugging from the outlet. Never yank the cord to disconnect from the outlet; instead, grasp the plug and pull to disconnect.
• Always disconnect the iron from the electrical outlet when filling with water or emptying, and also when not in use.
• To protect against the risk of electric shock, do not operate this product with wet hands, spill liquid on the appliance, or submerge it in water or any other liquid.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be closely supervised at all times to ensure that they do not play with the appliance.
• Please ensure the mains power supply is 220-24OV ~ 50/60Hz or 100-127V ~ 50/60Hz.
• Do not operate the iron if the power cord is damaged or if the iron has been dropped or damaged. To avoid a risk of electric shock, do not disassemble the iron. Take it to a qualified service person for examination and repair, or contact our customer service. Incorrect reassembly can cause a risk of electric shock when the iron is used.
• Never try to replace the parts or repair the appliance by yourself.
• Do not use an extension cord to operate this unit.
• To reduce the likelihood of circuit overload, DO NOT operate another high-wattage appliance on the same circuit as this unit.
• Do not place the appliance on or near a hot gas or a heated oven.
• Do not let the power cable hang over the edge of a table or counter or touch a hot surface. Let the iron cool completely before putting it away.
• Pay close attention to the iron whilst in use. The iron must not be left unattended while it is connected to the main socket.
• Do not use any attachments which are not listed in this manual.
• Keep the hot soleplate away from body parts and heat-sensitive objects.
• Keep the appliance well away from surfaces and objects that can be damaged by heat.
• Burns can occur from touching hot metal parts, hot water, or steam. Always hold the iron by the handle. Do not touch the soleplate while the unit is in use.
• Do not turn the unit upside down – hot water may drip out from holes in the Water Tank Windows.
• To reduce the risk of contact with hot water emitting from steam vents, check the appliance before each use by positioning it away from the body and setting the steam On/Off Switch.
• Do not leave water in the water tank when iron is not in use – this can corrode and damage the soleplate.
• Ensure there is adequate space to operate the iron.
• When not ironing, place the iron down onto the Silicone Mat (Patterned side facing up), on a level heatproof surface.
• Use this iron only with a purpose-built ironing board
• Observe all of the ironing instructions and ironing temperature dot settings given by the garment manufacturer. These guidelines are normally on the label/s inside the garment.
• Always ensure the water filling does not exceed the MAX mark on the water inlet.
• Do not iron buttons or fasteners. This could damage the iron.
• Do not iron directly onto synthetic fabric – instead iron the fabric inside out or with the synthetic fabric covered by other material to protect it.

Product Description

How to Use

Setting Voltage
The BEAUTURAL Travel Steam Iron features dual-voltage functionality, which allows it to function correctly in regions with either 100-127V or 220-240V electrical voltage standards. Voltage is set using the Voltage Selector. For use in Canada or North America, the voltage selector switch should be placed in the 110V position. For use in most foreign countries, the selector switch must be placed in the 230V position. CONFIRM the voltage available at each location before using the iron.

• NOTE: For connection to a 230 volt supply an adaptor plug may be needed.
• IMPORTANT: By default, the Voltage Selector is set to the 100-127V setting. Be sure to select the correct voltage for your location before plugging the power cord into an electrical outlet.

Filling Water Tank

Only fill the iron with water if you intend to use the steam function. For dry ironing, you do not need to fill the tank with water.

1. Unplug the unit and make sure the Steam ON/OFF Switch is off (set the switch to display “O” as shown in FIGURE 4B).

2. Place the unit (Soleplate down) on a flat, heat-resistant surface.

3. Fill the Measuring Cup with water.
   NOTE: To extend the life of your unit and keep it functioning at its maximum potential, it is highly recommended that distilled or de-mineralized water be used in Water Tank. Avoid using water containing softeners, perfumes or additives.

4. Open the water inlet cap and slowly pour the water from the measuring cup into the water tank (FIGURE 1). Close the cap.

Operating Unit

Dry Ironing

IMPORTANT: Make sure the Steam ON/OFF Switch is off (set the switch to display “0” as shown in FIGURE 4B) before dry ironing. This will prevent any water from accidentally dripping.

1. Plug the power cord into a convenient electrical outlet.

2. Place the Silicone Mat in an easy-to-reach place with the patterned side facing up.

3. Sort out the garments according to their ironing temperatures.
   Steam ironing is only possible with the temperature control dial set to the MAX position.
   NOTE: It is recommended to start with lower temperatures first, as high settings designed for heavy materials can damage delicate fabrics.

4. Turn the Temperature Control Dial clockwise so that the small arrow” ” on the Handle (FIGURE 2) points to one of three heat settings on the Dial. The heating Indicator Light will illuminate.

5. When Heating Indicator Light goes off, the iron is heated and ready for use.

6. If you need to put down the iron to handle the fabric during use, place the iron on the Silicone Mat(Patterned side facing up).

NOTE: During use, the Heating Indicator Light will cycle on and off as the unit works to maintain a constant temperature. You may continue to iron while Light cycles.

Steam Ironing

1. Plug the power cord into a convenient electrical outlet.

2. Turn the Temperature Control Dial clockwise to the MAX position to choose MAX temperature. The heating Indicator Light will illuminate.

3. Wait until the Heating Indicator Light turns off, and set the Steam ON/OFF Switch to display “ ” (FIGURE 4A). Hold the iron horizontally for a few seconds and the unit will begin emitting steam from steam vents on the soleplate.
   NOTE: The unit is designed to steam horizontally. Steam flow will stop whenever the unit is in a vertical upright position.

4. To stop the steam flow, slide the Steam ON/OFF Switch to display “0” (FIGURE 4B).

Once all ironing tasks are finished, immediately slide the Steam ON/OFF Switch to display “0” (FIGURE 4B), and turn the Temperature Control Dial counter- clockwise to the minimum setting. This will prevent water from accidentally dripping during the next use.

Cleaning and Storage

1. Turn the Temperature Control Dial counter-clockwise to the “0” position. Unplug the power cord.
2. Place the iron on the Silicone Mat( Patterned side facing up) and leave it to cool for 30 minutes.
3. Open the Water Inlet Cap and drain any remaining water into a sink or tub. Close Cap when finished.
4. Wipe the Main Body and Soleplate with a soft cloth lightly moistened with water.
   • DO NOT clean the Soleplate with detergents or descalers.
   • DO NOT clean the Soleplate with abrasive or corrosive products.
   • DO NOT submerge the unit or hold the unit under running water.
5. Wrap the power cord around the base of the Handle and secure the end in a Cable Clip (FIGURE 5). Place the silicone pad over the soleplate, then put the device and measuring cup in a cool, dry place.

Mineral Build-up

1. Follow STEPS 1-3 under the CLEANING & STORAGE section above; however, leave the Water Tank Cap open.
2. Make a mixture of 0.5 oz. distilled water and 0.5 oz. vinegar.
3. Using the included Measuring Cup, pour the water-vinegar solution into the Water Tank. Close Water Tank Cap.
4. Follow normal steam ironing procedure. Allow the unit to steam out the full contents of the Water Tank. When finished, lock the Steam Button in a lowered position and unplug the unit.
5. Allow to cool for 5 minutes, then refill Water Tank with fresh distilled water. Repeat STEP 4 until the vinegar odor dissipates.
6. Store unit as normal.

Specifications

• Model : 1-MR08US04, -870
• Rated Voltage : 100-127V/220-240V
• Rated Power : 301-499W/343-408W
• Water Capacity :1.4fl oz(40ml)

NOTE: Design and specifications are subject to change without notice. This product’s packaging is made from environmentally friendly material and can be disposed of at your local recycling plant.

Customer Service

• UNITED STATES
  • Phone: +1 909-391-3888 (Mon-Fri 9:00 am – 5:00 pm PST) Email: ushelp@1byonebros.com
• CANADA
  • Email: cahelp@1byonebros.com
• UNITED KINGDOM
  • Email: ukhelp@1byonebros.com
• GERMANY/FRANCE ITALY/SPAIN
  • Email: euhelp@1byonebros.com

BRAND OWNER
1byone Products Inc. 1230 E Belmont Street, Ontario, CA, USA 91761 Customer Service: +1 909-391-3888 on www.1byonebros.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>