outdoor lifestyles ODCTGWD Series Woodburning Fireplace Owner’s Manual
- July 30, 2024
- outdoor lifestyles
Table of Contents
ODCTGWD Series Woodburning Fireplace
Specifications
Model(s):
ODCTGWD-36, ODCTGWD-36H, ODCTGWD-42, ODCTGWD-42H
Type: Woodburning Fireplace
Manufacturer: Outdoor Lifestyles, a registered
trademark of Hearth & Home Technologies
Product Information
The Outdoor Lifestyles wood burning fireplace is designed to
provide safety and reliability. It is recommended to have
installation and service performed by qualified professionals. Use
solid wood fuel only to prevent fire risks and the generation of
poisonous gases.
Owner’s Manual
Read the manual before installing or operating the fireplace.
Retain the manual for future reference.
Installation
-
Have the fireplace installed by qualified personnel.
-
Ensure proper ventilation and clearance around the
fireplace. -
Use solid wood fuel only.
Operation
-
Before lighting the first fire, carefully read and follow all
instructions in the manual. -
Pay attention to safety warnings and cautions.
-
Keep the fireplace clean and well-maintained.
Maintenance
Regular maintenance is essential for safe and efficient
operation of the wood burning fireplace. Refer to the manual for
detailed maintenance procedures.
Product Usage Instructions
Installation
-
Have the fireplace installed by qualified personnel.
-
Ensure proper ventilation and clearance around the fireplace
according to the manufacturer’s guidelines. -
Use appropriate solid wood fuel as specified in the
manual.
Operation
-
Read and follow all instructions in the manual before lighting
the first fire. -
Ensure all safety precautions are in place before operating the
fireplace. -
Maintain a clean and well-ventilated environment around the
fireplace during operation.
Maintenance
-
Regularly inspect and clean the fireplace components as per the
maintenance schedule outlined in the manual. -
Check for any signs of wear or damage and address them
promptly. -
Keep the fireplace area clear of any flammable materials.
FAQ
Q: Can I use any type of fuel in the wood burning
fireplace?
A: No, it is recommended to use solid wood fuel only to prevent
fire risks and the generation of poisonous gases.
Q: How often should I clean the fireplace?
A: Regular maintenance is essential. Follow the maintenance
schedule outlined in the manual for cleaning instructions.
Owner’s Manual
Operation and Care
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Model(s):
ODCTGWD-36 ODCTGWD-36H ODCTGWD-42 ODCTGWD-42H
WOODBURNING FIREPLACE
Installation and service of this appliance should be performed by qualified
personnel. Hearth & Home Technologies recommends HHT Factory Trained or NFI
certified professionals.
WARNING: If the information in these instructions is not followed exactly, a
fire or explosion may result causing property damage, personal injury, or
death.
· DO NOT store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
· DO NOT overfire. Overfiring will void your warranty.
· Comply with all minimum clearances to combustibles as specified. Failure to
comply may cause house fire.
WARNING
HOT SURFACES! Glass and other surfaces are hot during operation AND cool down.
Hot glass will cause burns. · DO NOT touch glass until it is cooled · NEVER
allow children to touch glass · Keep children away · CAREFULLY SUPERVISE
children in same room as fireplace. · Alert children and adults to hazards of
high temperatures.
High temperatures may ignite clothing or other flammable materials. · Keep
clothing, furniture, draperies and other flammable
materials away.
WARNING
Fire Risk.
For use with solid wood fuel only. Other fuels may overfire and generate
poisonous gases (i.e. carbon monoxide).
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
1
Safety Alert Key:
· DANGER! Indicates a hazardous situation which, if not avoided will result in
death or serious injury. · WARNING! Indicates a hazardous situation which, if
not avoided could result in death or serious injury. · CAUTION! Indicates a
hazardous situation which, if not avoided, could result in minor or moderate
injury. · NOTICE: Indicates practices which may cause damage to the fireplace
or to property.
Table of Contents
1 Welcome
4 Maintenance and Service
A. Congratulations
3
A. Chimney Inspection
14
B. LIMITED LIFETIME WARRANTY
4
B. Creosote (Chimney) Cleaning
14
2 Product Specific and General Information
A. Appliance Certification
6
B. Vented & Unvented Gas Log Sets, Gas Inserts,
Gas Log Lighters, Wood-burning Inserts
6
C. Grate D. Glass Cleaning E. Ash Removal F. Refractory
15 15 15 15
3 Important Safety and Operating Information
A. Fireplace Safety
7
5 Troubleshooting A. FAQs
17
1. Clear Space
7
6 Reference Materials
2. Grate
8
A. Service Parts
19
3. Refractory 4. Firescreen
8
B. Accessories
23
8
C. Contact Information
24
5. Flue Damper
8
6. Glass Doors
8
7. Over-Firing Your Fireplace
8
8. Chimney Fire
9
B. General Operating Parts
9
1. Flue Damper
10
2. Outside Air
10
3. Glass Doors
10
C. Fuel
11
1. Hardwood vs. Softwood
11
2. Moisture content
11
3. Seasoning
12
4. Storing Wood
12
5. Burning Process
12
6. Creosote Formation
12
7. Processed Solid Fuel Firelogs
12
D. First Fire
12
E. Lighting Instructions
13
2
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
1 Welcome
Read this manual before installing or operating this fireplace. Please retain
this owner’s manual for future references.
A. Congratulations
Congratulations on selecting a Outdoor Lifestyles wood burning fireplace. The
Outdoor Lifestyles fireplace you have selected is designed to provide the
utmost in safety and reliability.
As the owner of a new fireplace, you’ll want to read and carefully follow all
of the instructions contained in this Owner’s Manual. Pay special attention to
all Cautions and Warnings.
This Owner’s Manual should be retained for future reference. We suggest that
you keep it with your other important documents and product manuals.
Your new Outdoor Lifestyles wood burning fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the Outdoor Lifestyles
family of fireplace products!
Outdoor Lifestyles is a registered trademark of Hearth & Home Technologies.
Local Dealer Information
DEALER: Fill in your name, address, phone and email information here and fireplace information below.
Dealer Name: ____ Address:
____ Phone: _____ Email:
Fireplace Information: Brand: ____
Model Name: ___
Serial Number:__ Date Installed:
Listing Label Information/Location
The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.
Serial Number
Fireplace Model
FIREPLACE NO.
WARNING: RISK OF FIRE DAMAGE. REPLACE
MODEL NO.
GRATE WITH HEARTH & HOME
TECHNOLOGIES
MODEL NO.
MFG. DATE
OUTDOOR FIREPLACE FOR USE WITH HEARTH & HOME TECHNOLOGIES LISTED FIREPLACE PARTS. SEE INSTALLATION AND OPERATING INSTRUCTIONS FOR THIS MODEL. ONLY HEARTH & HOME TECHNOLOGIES GLASS DOOR KITS CAN BE INSTALLED ON THIS UNIT.
CAN/ULC-S610
USE HHT SL SERIES CHIMNEY
CLEARANCE TO CHIMNEY COMBUSTIBLES: 2 IN. MIN.
FIREBOX
IN. MIN.
WARNING! TO AVOID THE RISK OF DAMAGING FIREPLACE MATERIALS AND INCREASING THE RISK OF SPREADING A FIRE DO NOT USE THE FIREPLACE TO COOK OR WARM FOOD.
DO NOT OVERFIRE. USE ONLY: SOLID WOOD FUEL OR LISTED DECORATIVE GAS APPLIANCE. DO NOT USE A FIREPLACE INSERT OR OTHER PRODUCTS NOT SPECIFIED FOR USE WITH THIS PRODUCT. IF DOORS ARE USED OPERATE FIREPLACE WITH DOORS FULLY OPEN OR CLOSED ONLY. WHEN BURNING A DECORATIVE GAS APPLIANCE IN THE FIREPLACE, ADJUST DAMPER TO THE FULLY OPEN POSITION.
ONLY UNVENTED GAS LOG SETS WHICH HAVE BEEN FOUND TO COMPLY WITH THE STANDARD FOR UNVENTED ROOM HEATERS, ANSI Z21.11.2 ARE TO BE INSTALLED IN THIS FIREPLACE. WARNING: DO NOT OPERATE AN UNVENTED LOG SET IN THIS FIREPLACE WITH THE CHIMNEY REMOVED.
UTILISER DU CARBURANT SOLIDE SEULEMENT
IF INSTALLATION OR OPERATING INSTRUCTIONS ARE MISSING CONTACT: HEARTH & HOME TECHNOLOGIES, 7571 215th Street West, Lakeville, MN 55044
P.N. 4021-781C
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
3
B. LIMITED LIFETIME WARRANTY
Outdoor Lifestyles by Hearth & Home TechnologiesTM Limited Lifetime Warranty
Hearth & Home Technologies (“HHT”) extends the following warranty for all
Outdoor Lifestyles by HHTTM brand products (“Products”) that are purchased
from an HHT authorized dealer.
WARRANTY COVERAGE: HHT warrants to the original owner of the Product at the
site of installation, and to any transferee taking ownership of the Product at
the site of installation within one year following the date of original
purchase, that the Product will be free from defects in materials and
workmanship at the time of manufacture. After installation, if covered
components manufactured by HHT are found to be defective in materials or
workmanship during the applicable warranty period, HHT will, at its option,
repair or replace the covered components. This warranty is subject to
conditions, exclusions and limitations as described below.
WARRANTY PERIOD: The warranty period begins on the earlier of: (i) the date of
invoice for the Product; (ii) in the case of new home construction, the date
of first occupancy of the residence or six months after the date of sale of
the Product by an HHT authorized dealer, whichever occurs first; or (iii) the
date 24 months following the date of Product shipment from HHT, regardless of
the invoice or occupancy date.
WARRANTY CONDITIONS: · The Limited Lifetime Warranty covers Products that are
purchased through a HHT authorized dealer or distributor. A list of HHT
authorized dealers is available on the HHT branded websites. · This warranty
is only valid while the Product remains at the site of original installation.
· Contact your installing dealer for warranty service. If the installing
dealer is unable to provide necessary parts, contact the nearest HHT
authorized dealer. Additional service fees may apply if you are seeking
warranty service from a dealer other than the dealer from whom you originally
purchased the Product. · Check with your dealer in advance for any costs to
you when arranging a warranty call. Travel and shipping charges for parts are
not covered by this warranty. · The Product body, metal firebox and heat
exchanger carry the Limited Lifetime Warranty from the date of installation. ·
The following components do not carry the Limited Lifetime Warranty but are
warranted as follows: o One Year from Date of Installation: Gas and Electrical
Components or Gaskets Nickel Plated Materials · Excludes tarnishing Glass
Breakage, Logs/Refractory/Glass Panels due to thermal breakage · Surface,
hairline cracks, scratches and slight color changes are not covered Venting,
optional accessories, optional glass doors Labor Associated with Warranty
Service Work
WARRANTY EXCLUSIONS: This warranty does not cover the following:
· Changes in surface finishes as a result of normal use. As a heating
appliance, some changes in color of interior and exterior surface finishes may
occur; this is not a flaw and not covered under warranty.
· Damage to printed, plated, or enameled surfaces caused by fingerprints,
accidents, misuse, scratches, melted items, or other external sources and
residues left on surfaces from the use of abrasive cleaners or polishes.
· Repair or replacement of parts that are subject to normal wear and tear
during the warranty period. These parts include: paint, firebricks, grates,
flame guides and the discoloration of glass.
· Minor expansion, contraction, or movement of certain parts causing noise.
These conditions are normal and complaints related to this noise are not
covered by this warranty.
Outdoor Lifestyles Warranty – 2108-975C 6/5/2019 – 1
4
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
· Damages resulting from: (1) failure to install, operate, or maintain the
Product in accordance with the installation instructions, operating
instructions, and listing agent identification label furnished with the
Product; (2) failure to install the Product in accordance with local building
codes; (3) shipping or improper handling; (4) improper operation, abuse,
misuse, continued operation with damaged, corroded or failed components,
accident, or incorrectly performed repairs; (5) inadequate ventilation,
negative pressure or environmental conditions, including, without limitation:
hail, snow, ice, fallen branches, flooding, water damage and fading of color;
(6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the Product or any other
components not expressly authorized and approved by HHT; (8) modification of
the Product not expressly authorized and approved by HHT in writing; and/or
(9) interruptions or fluctuations of electrical power supply to the Product.
· Non-HHT venting components, hearth components or other accessories used in
conjunction with the Product.
· Any part of a pre-existing fireplace system in which an insert or a
decorative gas appliance is installed.
· The Product’s capability to heat the desired space. Information is provided
to assist the consumer and the dealer in selecting the proper appliance for
the application. Consideration must be given to the Product’s location and
configuration and environmental conditions.
This warranty is void if: · The Product has been over-fired or operated in
atmospheres contaminated by chlorine, fluorine, or other damaging chemicals.
Over-firing can be identified by, but not limited to, warped plates or tubes,
rust colored cast iron, bubbling, cracking and discoloration of steel or
enamel finishes and cracking or spalling of refractory or cementitious
materials. · The Product is subjected to prolonged periods of dampness,
condensation, ice or snow. · There is any damage to the Product or other
components due to water or weather damage which is the result of, but not
limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY: Repair or replacement in accordance with the
provisions of this warranty will be the owner’s exclusive remedy for and will
constitute HHT’s sole obligation under this warranty, under any other warranty
(express or implied), or in contract, tort or otherwise; provided, however,
that if HHT is unable to provide repair or replacement in an expedient and
cost effective manner, HHT may discharge all such obligations by refunding the
purchase price of the Product. No employee, agent, dealer, or other person is
authorized to give any warranty on behalf of HHT. TO THE EXTENT ALLOWED BY
LAW, HHT MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. HHT WILL NOT BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING OUT OF DEFECTS IN OR USE
OF THE PRODUCTS. Some states do not allow exclusions or limitation of
incidental or consequential damages, so these limitations may not apply to
you. This warranty gives you specific rights; you also may have other rights,
which vary from state to state. The duration of any implied warranty is
limited to the duration of the warranty period specified herein.
Outdoor Lifestyles Warranty – 2108-975C 6/5/2019 – 2
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
5
2 Product Specific and General Information
A. Appliance Certification
This fireplace system has been tested and listed in accordance with UL 127 and
CAN/ULC-S610 standards by Underwriters Laboratories Inc. for installation and
operation in the United States and Canada.
This fireplace may be installed in sleeping rooms EXCEPT in manufactured
homes. If installed with a gas log set, provisions for the National Fuel Gas
Code must be met.
This fireplace has been tested and listed for use with the optional components
specified in this manual. These optional components may be purchased
separately and installed at a later date. Installation of an outside air kit
will require significant reconstruction and is best if installed at the time
of fireplace installation.
Outdoor Lifestyles is a registered trademark of Hearth & Home Technologies.
Warning! Risk of Fire! For use with solid wood fuel only. Other fuels may
overfire and generate poisonous gases (i.e. carbon monoxide).
Warning! Risk of Fire! To avoid the risk of damaging fireplace materials and
increasing the risk of spreading a fire, do not use the fireplace to cook or
warm food.
B. Vented Gas Log Sets, Unvented Gas Log Sets, Gas or Wood Inserts and Gas Log
Lighters
· Optional · Gas log sets, gas or wood inserts, or gas log-lighters
can be installed in this fireplace. Follow the instructions provided with the
accessory for operation.
Unvented Gas Logs
CAUTION! If an unvented gas appliance is installed in the fireplace, the gas
appliance must only be operated with the fireplace glass door fully open (if
included). Only unvented gas log sets which have been found to comply with the
standard for unvented room heaters, ANSI Z211.11.2, are to be installed in
this fireplace. If an unvented gas appliance is installed it must incorporate
an automatic shutoff device, and must be installed in accordance with the
National Fuel Gas Code Z223.1, Latest edition.
WARNING! Do Not operate an unvented gas log set in this fireplace with the
chimney removed.
6
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
3 Important Safety and Operating Information
A. Fireplace Safety
Most problems are caused by improper installation and operation of the
fireplace. To provide reasonable fire safety, the following should be given
serious consideration:
· The fire should be supervised whenever the fireplace is in use.
· An annual inspection should be performed on the fireplace system.
· Install at least one smoke detector on each floor of your home to ensure
your safety.
· Install a conveniently located Class A fire extinguisher near the fireplace.
· Devise a practiced evacuation plan, consisting of at least two escape
routes.
· Devise a plan to deal with a chimney fire: – Evacuate. – Notify the fire
department.
WARNING! Risk of Fire! Hearth & Home Technologies disclaims any responsibility
for, and the warranty and agency listing will be voided by the following
actions.
DO NOT: · operate damaged fireplace · modify fireplace · overfire · install
any unvented gas log set · install any component not approved by Hearth & Home
Technologies · install parts or components not Listed or approved · operate
the fireplace without fully assembling all
components
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage.
1. Clear Space
Combustible materials must not be stored on the hearth extension. Room
furnishings such as drapes, curtains, chairs or other combustibles must be at
least 4 ft (1219 mm) from the open front of the fireplace.
Combustible materials are materials made of or surfaced with any of the following materials:
– Wood
– Compressed paper
– Plant fibers
– Plastic
– Plywood/OSB – Drywall
– Any material that can ignite and burn, flame proofed
or not, plastered or un-plastered.
Non-combustible materials are materials which will not ignite and burn, composed of any combination of the following:
– Steel
– Brick – Concrete – Glass
– Iron
– Tile – Slate – Plasters
WARNING! Risk of Fire! Keep combustible materials, gasoline and other
flammable vapors and liquids clear of the fireplace.
DO NOT: · store flammable materials close to the fireplace · use gasoline,
lantern fuel, kerosene, charcoal lighter
fluid or similar liquids to start or “freshen up” a fire in this fireplace.
WARNING: This product and the fuels used to operate this product (wood and wood pellets), and the products of combustion of such fuels, can expose you to chemicals including carbon black, which is known to the State of California to cause cancer and carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to: www. P65Warnings.ca.gov.
48 in. (1219 mm) Clear Space
Front of Fireplace
12 in. (305 mm) Clear Space
Sides of Fireplace (from the FP opening)
48 1/8 in. (1222 mm) Clear Space
Bottom of Fireplace to Lower Edge of Mantel
or Trim
Figure 3.1 Clear Space
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
7
2. Grate This fireplace is designed to be used with the supplied grate or one
approved by HHT.
WARNING! Risk of Fire! Use only the factory-supplied integral grate. · Keeps
logs in place. · Allows proper air circulation around the fire.
3. Refractory The refractory is supplied to contain heat and provide an
attractive interior. It will break down over time and will need occasional
replacement. Small hairline cracks and discoloration are normal and do not
affect its safety. WARNING! Risk of Fire! DO NOT burn fireplace without
refractory. Use only refractory supplied by Hearth & Home Technologies.
4. Firescreen The firescreen is provided to control sparks. Keep it closed
when the fireplace is in use.
WARNING! Risk of Fire or Burns! · Screen will not prevent burning materials
from falling
out. · Screen pulls or handles may be hot.
5. Flue Damper The flue damper must be in the fully opened position during
operation of the fireplace.
WARNING! Risk of Fire and Asphyxiation! Open damper prior to operating
fireplace. A closed damper overfires the fireplace and spills smoke and flames
into the room.
6. Glass Doors Glass doors are optional. WARNING! Risk of Fire! Install ONLY
doors approved by Hearth & Home Technologies. WARNING! Risk of Fire and Smoke!
Fireplace equipped with doors should be operated only with doors fully open or
doors fully closed. If doors are left partly open, gas and flame may be drawn
out of the fireplace opening.
7. Over-Firing Your Fireplace
WARNING! Risk of Fire! Do not over-fire. Over-firing may ignite creosote or
will damage the fireplace and chimney. To prevent over-firing your fireplace.
DO NOT:
· use flammable liquids · overload with wood · burn trash or large amounts of
scrap lumber
Symptoms of over-firing may include one or more of the following:
· chimney connector or fireplace glowing · roaring, rumbling noises · loud
cracking or banging sounds · metal warping · chimney fire
8. Chimney Fire In the event of a chimney fire
· Have the chimney and adjacent structure inspected by qualified
professionals. Hearth & Home Technologies recommends that NFI or CSIA
certified professionals, or technicians under the direction of certified
professionals, conduct a minimum of an NFPA 211 Level 2 inspection of the
chimney.
· Replace components of the chimney and fireplace as specified by the
professionals.
· Ensure all joints are properly engaged and the chimney is properly secured.
WARNING! Risk of Fire! A chimney fire can permanently damage your chimney
system. Failure to replace damaged components and make proper repairs can
cause a structure fire.
8
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
WARNING
HOT SURFACES!
Glass and other surfaces are hot during operation AND cool down.
Hot glass will cause burns. · DO NOT touch glass until it is cooled · NEVER
allow children to touch glass · Keep children away · CAREFULLY SUPERVISE
children in same room as fireplace. · Alert children and adults to hazards of
high temperatures. High temperatures may ignite clothing or other flammable
materials. · Keep clothing, furniture, draperies and other flammable materials
away.
CAUTION! If you expect that children may come into contact with this
fireplace, we recommend a barrier such as a decorative screen. See your dealer
for suggestions.
B. General Operating Parts
WARNING! DO NOT operate fireplace before reading and understanding operating
instructions. Failure to operate fireplace according to operating instructions
could cause fire or injury.
Outside Air Handle up – open
Handle down closed
Figure 3.2 General Operating Parts
open
Damper close Handle
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
9
1. Flue Damper
The flue damper must be in the fully opened position (handle up toward the top
of the firepalce) during operation of the fireplace.
Before lighting the fireplace, verify fully open position by looking up from
the inside of the fireplace.
3. Glass Doors · Glass doors are optional. · Refer to Figure 3.3 for how to properly use them.
FULLY OPEN CORRECT
PARTLY OPEN INCORRECT
2. Outside Air
Refer to Figure 3.2 for location and operation of control. The outside air kit
supplies some combustion air for your fireplace. It may help reduce the
effects of negative air pressure.
Close the inlet to prevent cold drafts when the fireplace is not being used
CAUTION! Outside air control handle may be warm. Adjust before lighting fire.
FULLY CLOSED PARTLY CLOSED
CORRECT
INCORRECT
Figure 3.3 Operating Positions of Bi-fold Doors
10
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
C. Fuel
WARNING! For use with solid wood fuel only.
Other fuels may overfire and generate poisonous gases (i.e. carbon monoxide).
1. Hardwood vs. Softwood
Your fireplace’s performance depends on the quality of the firewood you use.
One species of wood varies very little to the other in terms of energy
content. All seasoned wood contains about 8,000 BTU’s per pound. Hardwoods
have a greater density than softwoods; a piece of hardwood will contain about
60% more BTU’s than an equal size piece of softwood. A cord of seasoned oak
(hardwood) would contain about 60% more potential energy than a cord of
seasoned pine (softwood).
Most softwoods are coniferous. These are trees with needle-like leaves that
stay green all year and carry their seeds exposed in a cone. Examples of
coniferous trees are Douglas fir, pine, spruce and cedar. Softwoods, being
more porous, require less time to dry, burn faster and are easier to ignite
than hardwoods. Hardwoods are deciduous trees, broadleaf trees that lose their
leaves in the fall. Their seeds are usually found within a protective pod or
enclosure. Some examples of deciduous trees are oak, maple, apple, and birch.
However, it should be noted that there are some deciduous trees that are
definitely not considered hardwoods such as poplar, aspen and alder. Hardwoods
require more time to season, burn slower and are usually harder to ignite than
softwoods. Obviously, you will use the type of wood that is most readily
available in your area. However, if at all possible the best arrangement is to
have a mix of softwood and hardwood. This way you can use the softwood for
starting the fire, giving off quick heat to bring the fireplace up to
operating temperature. Add the hardwood for slow, even heat and longer burn
time.
WARNING! Risk of Fire! · DO NOT burn wet or green wood. · Wet, unseasoned wood
can cause accumulation of
creosote.
2. Moisture content
The majority of the problems fireplace owners experience are caused by trying
to burn wet, unseasoned wood. Freshly cut wood can be as much water as it is
wood, having a moisture content of around 50%. Imagine a wooden bucket that
weighs about 8 pounds. Fill it with a gallon of water, put it in the firebox
and try to burn it. This sounds ridiculous but that is exactly what you are
doing if you burn unseasoned wood. Dead wood lying on the forest floor should
be considered wet, and requires full seasoning time. Standing dead wood can be
considered to be about two-thirds seasoned, if cut at the dry time of the
year.
Burning wet, unseasoned wood will produce less heat output because it requires
energy in the form of heat to evaporate the water trapped inside. This is
wasted energy that should be used for heating your home. This moisture
evaporates in the form of steam which has a cooling effect in your firebox and
chimney system. When combined with tar and other organic vapors from burning
wood it will form creosote which condenses in the relatively cool firebox and
chimney.
Even dry wood contains at least 15% moisture by weight, and should be burned
hot enough to keep the chimney hot for as long as it takes to dry the wood out
– about one hour. To tell if wood is dry enough to burn, check the ends of the
logs. If there are cracks radiating in all directions from the center, it is
dry. If your wood sizzles in the fire, even though the surface is dry, it may
not be fully cured.
Soft woods
· Douglas Fir · Pine · Spruce · Cedar · Poplar · Aspen · Alder
Hard woods
· Oak · Maple · Apple · Birch
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
11
3. Seasoning
Seasoned firewood is nothing more than wood that is cut to size, split and air
dried to a moisture content of around 20%. The time it takes to season wood
varies from around nine months for soft woods to as long as eighteen months
for hardwoods. The key to seasoning wood is to be sure it has been split,
exposing the wet interior and increasing the surface area of each piece. A
tree that was cut down a year ago and not split is likely to have almost as
high a moisture content now as it did when it was cut.
To season wood:
· Cut logs to size · Split to 6 in. (152 mm) or less · Air dry to a moisture
content of around 20%
– Soft wood – about nine months – Hard wood – about eighteen months
NOTICE: Seasoning time may vary depending on drying conditions.
4. Storing Wood
Splitting wood before it is stored reduces drying time. The following
guideline will ensure properly seasoned wood:
· Stack the wood to allow air to circulate freely around and through the
woodpile.
· Elevate the woodpile off the ground to allow air circulation underneath.
· The smaller the pieces, the faster the drying process. Any piece over 6 in.
(152 mm) in diameter should be split.
· Wood should be stacked so that both ends of each piece are exposed to air,
since more drying occurs through the cut ends than the sides. This is true
even with wood that has been split.
· Store wood under cover, such as in a shed, or covered with a tarp, plastic,
tar paper, sheets of scrap plywood, etc., as uncovered wood can absorb water
from rain or snow, delaying the seasoning process. Avoid covering the sides
and ends completely. Doing so may trap moisture from the ground and impede air
circulation.
5. Burning Process Fire requires fuel, air and heat. If heat is robbed from
the fireplace during the drying stage, the new load of wood has reduced the
chances for a good clean burn. Aways burn dry, seasoned firewood.
6. Creosote Formation and Need For Removal When wood is burned slowly, it
produces tar and other organic vapors which combine with expelled moisture to
form creosote. The creosote vapors condense in the relatively cool chimney
flue of a newly-started or a slow-burning fire. As a result, creosote residue
accumulates on the flue lining.
When ignited, creosote creates an extremely hot fire which may damage the
chimney or even destroy the house.
The chimney shall be inspected at least annually before lighting, or once
every two months during heating season.
When creosote has accumulated it shall be removed to reduce the risk of a
chimney fire.
7. Processed Solid Fuel Firelogs Manufactured firelogs may be used with this
fireplace. Hearth & Home Technologies recommends the use of ANSI/CAN/UL/ULC
2115 processed solid fuel firelogs and firestarters. Follow the manufacturer’s
lighting and safety instructions.
Using firelogs may require more frequent chimney inspections and cleaning.
Do not poke or stir the logs while they are burning. Use only firelogs that
have been evaluated for the application in manufactured fireplaces and refer
to firelog warnings and caution markings on packaging prior to use.
D. First Fire
Before lighting your first fire in the fireplace, make certain that:
· refractory is in place · all labels have been removed
Note: Homeowners are encouraged to provide smoke and carbon monoxide alarms in accordance with the authority having jurisdiction.
12
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
E. Lighting Instructions
NOTICE: You must establish a good draft to prevent smoke spillage into the
room.
The first three or four fires should be of moderate size to allow the oils and
binders to be burned from the fireplace and the refractory and paint to cure.
You may notice an industrial odor the first few fires. This is considered
normal.
Use well-seasoned wood.
· Open the flue damper to a fully open position. · Place crumpled or twisted
paper under the fireplace
grate. · Loosely arrange kindling or small pieces of wood to form
a `tent’ on the fireplace grate. · Pre-warm the flue to establish a draft to
help reduce
smoke spillage during start-up. Hold a rolled up piece of burning newspaper
under the flue damper for a few moments. · Light the crumpled paper to ignite
the kindling. · Add small pieces of wood until a hot bed of embers has been
established. · Add a minimum of three average size pieces of split firewood,
placed to allow combustion air and flames between them.
WARNING! Risk of Fire! Keep combustible materials, gasoline and other
flammable vapors and liquids clear of the fireplace. DO NOT: · store flammable
materials close to the fireplace · use gasoline, lantern fuel, kerosene,
charcoal lighter
fluid or similar liquids to start or “freshen up” a fire in this fireplace.
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
13
4 Maintenance and Service
WARNING! Hot Surfaces! Glass and other surfaces are hot during operation AND
cool down. DO NOT clean fireplace until it is cooled.
Installation and repair should be done by a qualified service technician only.
The fireplace should be inspected before use and at least annually by a
professional service person.
The following tasks may be performed annually by the homeowner. If you are
uncomfortable performing any of the listed tasks, please contact your dealer
for a service appointment.
WARNING! Risk of Asphyxiation and Fire! Annual inspection by qualified
technician recommended. Check:
· condition of doors, surrounds and fronts · condition of glass and glass
assembly · obstructions of combustion and ventilation air · obstructions of
termination cap Clean: · glass · air passageways, grilles
A. Chimney Inspection
Frequency: As necessary; at least annually before lighting fireplace, or once
every two months during heating season. By: Homeowner/Chimney Sweep
· Confirm that termination cap remains clear and unobstructed.
· Inspect for blockages such as bird nests, leaves, etc. · Inspect for
corrosion or separation. · Inspect for creosote and remove as needed, at least
every two months during the heating season. · Inspect the system at the
fireplace connection and
at the chimney top.
In the event of a chimney fire, Hearth & Home Technologies recommends
replacement of the chimney and inspection of the adjacent structure to the
provisions of NFPA Level III inspection criteria.
B. Creosote (Chimney) Cleaning
Frequency: As needed; at least annually before lighting, or once every two
months during heating season. When creosote has accumulated it shall be
removed to reduce the risk of a chimney fire. By: Chimney Sweep Tools Needed:
Brush, Phillips screwdriver
· When wood is burned slowly, it produces tar and other organic vapors, which
combine with expelled moisture to form creosote. The creosote vapors condense
in the relatively cool chimney flue of a slow-burnign fire. As a result,
creosote residue accumulates on the flue lining. When ignited, this creosote
makes an extremely hot fire.
· Remove all ash from the firebox and extinguish all hot embers before
disposal. Allow the fireplace to cool completely.
· Remove the top of the termination cap as shown in Figure 4.1 to clean the
cap and chimney.
· The creosote or soot should be removed from the chimney with a brush
specifically designed for the size of chimney in use.
· Reinstall termination cap. · Clean out fallen debris from the firebox.
WARNING! Risk of Fire! Ignited creosote is extremely HOT. Prevent creosote
buildup.
14
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
Remove screws, lift top cover.
Top Cover
Remove 4 screws and lift top pan off.
Cap Chimney
TR11/TR11T TR444/TR442 Round Termination Cap
Cap
Slip Section
ST1175 ST475 Square Termination Cap
Remove 2 screws from the front and back and lift the top off.
SCREW
TCT1175 Terra Cotta Termination Cap Available US only
Figure 4.1 Chimney & Termination Cap Cleaning
1. REMOVE (8) SCREWS 2. LIFT TOP
TOP
TOP
SCREW
DT SERIES
C. Grate
Frequency: After each ash removal By: Homeowner
Inspect grate for: · Warping or sagging 1-1/2 in. (38 mm) or more · Broken
welds · Burn-through of grate bars For safe operation, replace only with the
approved grate from Hearth & Homes Technologies
D. Glass Cleaning
Frequency: As necessary By: Homeowner Tools Needed: Vinegar or glass cleaner,
soft towel
· Clean glass with a non-abrasive glass cleaner. Use a damp cloth dipped in
wood ashes or a commercially available oven cleaner. Remove any oven cleaner
residue with a glass cleaner or soap and water.
E. Ash Removal
Frequency: As necessary By: Homeowner Tools Needed: Covered metal container,
metal shovel, fireplace broom
WARNING! Risk of Fire! DO NOT remove ashes until the fire is out and the
fireplace is cold.
· Ashes should be placed in metal container with tight fitting lid.
· The closed container of ashes should be placed on a noncombustible floor or
on the ground, well away from all combustible materials, pending final
disposal.
· If the ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container until all cinders
have thoroughly cooled.
F. Refractory
Frequency: After each ash removal By: Homeowner
· Inspect condition of refractory. Replace if crumbly or otherwise
deteriorated, metal is exposed behind the refractory, or if cracks exceed 1/4
in. (6 mm).
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
15
5 Troubleshooting
Start Fire Problems Can’t get fire started Excessive smoke or spillage Burns
too slowly Smolders, sizzles
Fire burns too fast
Possible Cause Not enough kindling/paper or no kindling/paper Damper
closed/not fully open Not enough air for fire to ignite
Wood condition is too wet, too large
Solution
Use dry kindling, more paper. Arrange kindling & wood for air movement.
Open damper.
Check for restricted cap/shroud. Open air kit (if installed). Check for flue
blockage. Pre-warm flue before starting fire (refer to starting fire section).
Check for adequate vent height (refer to chimney assembly section). Open
window below the fireplace towards the wind. Use dry, seasoned wood (refer to
wood fuel section).
Bed of coals not established before adding wood
Flue blockage such as birds’ nests or leaves in termination cap
Start with paper & kindling to establish bed of coals (refer to starting fire
section).
Have chimney inspected for creosote and cleaned by a certified chimney sweep.
Down draft or negative pressure Competition with exhaust devices
Extremely dry or soft wood
No glass doors Overdrafting
Do not use exhaust fans during start-up (refer to negative pressure section).
Open window below the fireplace towards the wind.
Mix in hardwood.
Mix in less seasoned wood after fire is established (refer to wood fuel
section).
Add glass doors to slow down air flow.
Check for correct vent height; too much vertical height creates overdrafting.
Check location of vent termination (refer to chimney assembly section).
16
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
A. FAQs
Hearth & Home Technologies assumes no responsibility for the improper
performance of the fireplace system caused by inadequate draft due to
environmental conditions, down drafts, tight sealing construction of the
structure, or mechanical exhausting devices which will create a negative air
pressure within the structure where the fireplace is located.
If smoke spillage occurs from a fireplace opening when the door is open, there
is either a leakage in the flue, a blockage in the flue, or some condition is
affecting draft Understanding and differentiating the conditions which can
cause each of these kinds of spillage problems is essential to their solution.
· Flue Leakage Check for improperly connected flue joints or a damaged flue
joint in the chimney system. Such leakage would reduce draft (air would be
drawn in through the leaks rather than through the fireplace). The result
might be difficult start-up and smoky fires that might spill if other adverse
draft conditions accompany this problem.
· Flue Blockage The damper should be open. Check for objects that may have
fallen down the chimney.
Flue draft is measured as negative pressure in the chimney. The amount of
negative pressure determines how strong the draft is. The draft is important
because it draws the combustion air into the fireplace and pulls the smoke out
of the chimney.
There are three basic criteria essential in establishing and maintaining flue
draft:
· availability of combustion air · heat generated from the fire · diameter and
height of the flue system These three factors work together as a system to
create the flue draft. Increasing or decreasing any one of them will affect
the other two and thus change the amount of draft in the entire system.
If the fire is hard to start and smoke spills out of the fireplace, or you
find it difficult to establish and maintain a moderately high burn rate, then
the flue draft is too low and corrective measures must be taken.
Be sure you have air available for combustion and that your firewood is dry
and well seasoned. Build your fires properly and according to the instructions
given in operating instructions, “Starting a Fire”. Be sure your flue system
is installed correctly and that it is the proper diameter and height. Check
for the following:
· All chimney sections are properly installed. · The chimney is clean and free
of creosote or soot
buildup. · Make sure overhanging trees and branches are cut
back within ten feet of the top of the chimney and the chimney is free of
debris from animals. · Ensure the chimney cap is clean and free of any buildup
of soot or creosote if cap is equipped with a spark arrestor screen. · The
wood being used in dry and well seasoned.
If you still suspect you have a low draft problem it may be necessary to
increase the volume of air in your flue system. Since the diameter of your
flue system is matched with the size of the flue collar and should not be
changed, then the height of the system must be increased. Add chimney sections
one at a time until the draft improves.
In some cases, regardless of what you do, it can still be difficult to
establish the proper flue draft. This is especially evident when using an
exterior factory-built chimney or exterior masonry chimney. Try holding a
burning rolled up newspaper as close to the flue outlet as possible for a few
minutes, then light the paper under the kindling. The heat generated from the
burning rolled up newspaper should help get the draft established.
Still other factors can affect how well your flue system performs. Neighboring
structures, high winds, tall trees, even hillsides can affect air currents
around the chimney. Well designed chimney caps are available that can help.
Your fireplace dealer is the local expert in your area. He can usually make
suggestions or discover problems that can be easily corrected allowing your
fireplace to operate correctly as it has been designed, providing safe and
economical heat for your home.
Contact your dealer for additional information regarding operation and
troubleshooting. Visit wwwhearthnhome.com to find a dealer.
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
17
s arou
nd chimney termination? Strong wind
Another appliance in
home also exhausting
air (furnace, fan, dryer, etc.)?
Unsealed can lights?
Overhead fan operating?
Air register from furnace near fireplace?
Overhanging tree?
Bird’s nest or leaves in termination cap?
Structural changes in chimney area?
Creosote buildup in flue?
Doors opening and closing? Window closed for start-up?
Combustion air control
Outside air closed?
Figure 5.1 Factory-built Fireplaces: Troubleshooting
18
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
6 Reference Materials
A. Service Parts
Service Parts
ODCTGWD-36 ODCTGWD-36H
36″ Outdoor Woodburning Fireplace
Beginning Manufacturing Date: Jan 2023 Ending Manufacturing Date: Active
12 13
4
5 6 7 8 9 10
11
1
3 2
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS PART NUMBER
1
Starter Section Assembly
22072B
2
Damper Blade Assembly
SRV29964
3
Damper Control
SRV20549
Damper Weight
SRV19785
4
Rear Top Standoff
Qty 2 req
19228
5
Front Top Standoff
Qty 2 req
SRV11864
6
Upper Front
SRV4013-206BK
7
Top Front Face, Overlay
SRV4107-113
8 / 9 Right / Left Side Column, Overlay
Qty 2 req
SRV4108-105
10 Bottom Front Face, Overlay
SRV4107-114
11 Grate
Painted Black Stainless Steel
GR37 GR37SS
12 Smoke Shield
SRV4107-371
13 Firescreen Assembly
Qty 2 req
SRV4107-301
Firescreen Rod
Qty 2 req
SRV4107-300
Grate Retainer
Qty 2 req
SRV4017-060
Nailing Flange
Qty 4 req
SRV31190
Outside Air Kit
AK22
Fastener Pack
13580
Outside Air Shield
SRV33271
4 in. Outside Air Inlet Ring
25692
Screen Cover (top only)
SRV4107-115
Side Trim
Qty 2 req
SRV4108-116
Strip Protector
Qty 2 req
SRV18320
Additional service parts on following page.
Stocked in Depot
Y
Y Y Y Y Y
Y
01/24
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
19
Service Parts
ODCTGWD-36 ODCTGWD-36H
Beginning Manufacturing Date: Jan 2023 Ending Manufacturing Date: Active
Traditional
Herringbone
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
Brick Refractory – Back Brick Refractory – Hearth Brick Refractory – Left Side
Brick Refractory – Right Side
Brick Refractory – Back Brick Refractory – Hearth Brick Refractory – Side
(Left/Right Owner’s Manual Installation Manual
COMMENTS Herringbone Refractory
Traditional Refractory Qty 2 req
PART NUMBER
SRV4107-161 SRV4107-150 SRV4108-163 SRV4108-162
SRV4107-151 SRV4107-150 SRV4108-152 4108-900 4108-901
Stocked in Depot
20
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
12 13
Service Parts
ODCTGWD-42, ODCTGWD-42H
42″ Outdoor Woodburning Fireplace Beginning Manufacturing Date: Jan 2023 Ending Manufacturing Date: Active
4
5 6 7 8 9 10
11
1
3 2
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS PART NUMBER
1
Starter Section Assembly
22072B
2
Damper Blade Assembly
SRV29964
3
Damper Control
SRV20549
Damper Weight
SRV19785
4
Rear Top Standoff
Qty 2 req
19228
5
Front Top Standoff
Qty 2 req
SRV11864
6
Upper Front
SRV4013-207BK
7
Top Front Face, Overlay
SRV4108-113
8 / 9 Right / Left Side Column, Overlay
Qty 2 req
SRV4108-105
10 Bottom Front Face, Overlay
SRV4108-114
11 Grate
Painted Black Stainless Steel
GR38 GR38SS
12 Smoke Shield
SRV4108-371
13 Firescreen Assembly
Qty 2 req
SRV4108-301
Firescreen Rod
Qty 2 req
SRV4108-300
Grate Retainer
Qty 2 req
SRV4017-060
Nailing Flange
Qty 4 req
SRV31190
Outside Air Kit
AK22
Fastener Pack
13580
Outside Air Shield
SRV33271
4 in. Outside Air Inlet Ring
25692
Screen Cover (top only)
SRV4108-115
Side Trim
Qty 2 req
SRV4108-116
Strip Protector
Qty 2 req
SRV18320
Additional service parts on following page.
Stocked in Depot
Y
Y Y Y Y Y
Y
01/24
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
21
Service Parts
ODCTGWD-42, ODCTGWD-42H
Beginning Manufacturing Date: Jan 2023 Ending Manufacturing Date: Active
Traditional
Herringbone
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
Brick Refractory – Back Brick Refractory – Hearth Brick Refractory – Left Side
Brick Refractory – Right Side
Brick Refractory – Back Brick Refractory – Hearth Brick Refractory – Side
(Left/Right Owner’s Manual Installation Manual
COMMENTS Herringbone Refractory
Traditional Refractory Qty 2 req
PART NUMBER
SRV4108-161 SRV4108-150 SRV4108-163 SRV4108-162
SRV4108-151 SRV4108-150 SRV4108-152 4108-900 4108-901
Stocked in Depot
22
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
B. Accessories
Stainless Steel Grate
Bi-fold Glass Doors
Extended Smoke Shield
36/36H
42/42H
Description
DM6036-S
DM8042-S Glass doors – Bi-fold, clear view, SS
HX4
HX4
Hearth extension
GR37SS
GR38SS Stainless Steel Grate
ODCTGWD-FSK36 ODCTGWD-FSK42 Extended Smole Shield
Gas Inserts Gas Log Sets Gas Log Lighters Wood-burning Inserts
See your Outdoor Lifestyles dealer for a complete listing of optional components.
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
23
C. Contact Information
Hearth & Home Technologies 7571 215th Street West Lakeville, MN 55044
www.hearthnhome.com
Please contact your Outdoor Lifestyles dealer with any questions or concerns.
For the number of your nearest Outdoor Lifestyles dealer, please visit
www.hearthnhome.com.
NOTES
CAUTION
DO NOT DISCARD THIS MANUAL
· Important operating and maintenance
instructions included.
· Read, understand and follow these instructions for safe
installation and operation.
· Leave this manual with party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United
States) 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471,
5328356, 5341794, 5347983, 5413089, 5429495, 5452708, 5542407, 5890485,
5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165,
6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712,
6543698, 6550687, 6601579, 6672860, 6688302, 6688302B2, 6715724B2, 6729551,
6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441,
6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884,7047962,
7216645, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408,
2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents
pending.
Printed in U.S.A. – Copyright 2012
24
Outdoor Lifestyles by Hearth & Home Technologies · ODCTGWD Owner’s Manual · 4108-900 · Rev F · 2/24
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>