TUNDRA DRONE Siren Herder Drone User Guide
- June 3, 2024
- TUNDRA DRONE
Table of Contents
**
**
TUNDRA DRONE Siren Herder Drone
READ
BEFORE THE FIRST FLIGHT
Read the following documents before using the Tundra Drone Siren herder:
- USE AND CARE OF THE PRODUCT– CUSTOMER RESPONSIBILITY
- IMPORTANT SAFETY INFORMATION
- Specifications
- Product overview
- Charging the battery
- Prepare the DJI Remote controller’s GO 4-app before first flight
- How to use the DJI Remote controller with the Tundra Drone Siren herder
- Mount the Tundra Drone Siren herder unit on the aircraft and prepare for takeoff
- How to unmount and store the Tundra Drone Siren herder
- Support
USE AND CARE OF THE PRODUCT – CUSTOMER RESPONSIBILITY
The Drone Pilot shall only use the «Tundra Drone Siren herder» (her after Product) as the described in this manual. Drones, aircrafts, or unmanned aerial vehicles (UAVs) (hereafter aircraft or drone) mounted with the Product from Tundra Drone AS (her after Tundra Drone) shall only be used in accordance with the regulations for drone flying in the country in which the Drone Pilot operates. The Drone Pilot must ensure that the drone, where the Product is mounted, is insured at all times with statutory liability insurance, if required by national law in the country where operating the aircraft. The Drone Pilot understands that the use of a Product from Tundra Drone on drones may entail a higher risk due to the fact that mounting of additional drone equipment on the drone may affect the performance of the drone itself, in both short and long term. It is therefore recommended that the Drone Pilot performs more frequent maintenance of the drone than the drone manufacturer’s recommendations, to ensure that performance is not reduced. Furthermore, additional drone equipment mounted to the drone may increase the likelihood that weather and other conditions may affect the drone’s flight characteristics. The Drone Pilot understands that this constitutes conditions that the Drone Pilot must be especially careful with when flying the drone. The Drone Pilot must read and understand the user manuals for both the drone and the Product from Tundra Drone before the Product is used, and then carry out their own training with these in a calm, delimited and safe area, before the Drone Pilot takes the Product from Tundra Drone into ordinary use. Negligent use of drones with mounted drone equipment may lead to crashes, accidents or other dangers to the environment and people. If an incident as mentioned causes damage or death to people and animals, or damage to buildings, other physical objects or surroundings, and/or economic loss or damage, the Drone Pilot agrees that the Drone Pilot cannot hold Tundra Drone liable for damages, and the Drone Pilot waives the right to pursue Tundra Drone via legal action in any country. Should claims be made against Tundra Drone as a result of damage or loss that occurs when the Product is used by the Drone Pilot, or for breach of public and private regulations and permits, the Drone Pilot is obliged to indemnify Tundra Drone. This also applies if the damage occurs to a third party.
IMPORTANT SAFETY INFORMATION
Use with caution:
- The Tundra Drone Siren Herder outputs a very loud sound that may harm or damage your hearing permanently.
- Never use it stationary without any hearing protection for you and people around you. Always use hearing protection when operating it in close proximity (closer than 20 meters).
- Do not activate the siren sound before you have flown at least 20 meters away from yourself and other people.
- Never use the Tundra Drone Siren Herder indoors.
- Do not use the product in rain, snow or wet weather conditions.
- Do not expose the device for moisture.
- Do not place the device where it can be exposed to excessive heat or a dusty enviroment.
- Tundra Drone Siren herder is equipped with a rechargable lithium battery. Lithium batteries may have regulations and limitations for transportation, especially with air planes.
Please note that this product cannot be used in combination with DJI Goggles.
SPECIFICATIONS
- Sound output : 107dB
- Operating Range :1000 m (unobstructed)
- Modes : ON/OFF
- Battery Life : 75 minutes (with sound on continuously)
- Battery : 3.7V 380mAh, 1.4Wh
- Operating temperature :-10⁰C to 40⁰C (14⁰F to 104⁰F)
- Charging temperature range :5⁰C to 40⁰C (41⁰F to 104⁰F)
- Product size :8x4x4cm / 3.2×1.6×1.6”
- Weight :72g (0.15 lbs.)
- Color :Black
PRODUCT OVERVIEW
CHARGING THE BATTERY
Use a USB-C-cable to charge the Tundra Drone Siren herder’s battery before
first use. Charging time for empty battery can take up to 3 hours, depending
on the type of charger you use.
Indicator lights Green light
Power is on ON.
Blue light
Battery is charging. The battery is fully charged when the blue light is
turned off.
Red light
Battery is empty.
- DO NOT charge the Tundra Drone Siren herder’s battery immediately after flight as the temperature may be too high. Wait until the battery cools down to room temperature before charging again.
- The ideal charging temperature is 22o to 28o C (71.6o to 82.4o F).
PREPARE THE DJI REMOTE CONTROLLER’S DJI GO 4-APP BEFORE FIRST FLIGHT
-
Connect your smart phone to the DJI Mavic 2 Remote controller and turn ON the Remote controller.
-
Open the DJI GO 4-app from your smart phone.
-
Go to setting by tapping (General settings button)
-
Tap on the (Remote Controller Settings button)
-
Tap on the menu on the right side of «C2» and «scroll» up till you find the «Turn on/off Head LEDs» option; Tap on that to program this function to the «C2» button.
-
You have now successfully prepared the DJI GO 4-app for first flight with the Tundra Drone Siren herder.
HOW TO USE THE DJI REMOTE CONTROLLER WITH THE TUNDRA DRONE SIREN HERDER
- Prepare the DJI Mavic 2 aircraft for flight.
- Power up the aircraft and make sure that the DJI GO 4-app connects to the aircraft.
- Turn ON/OFF the aircraft’s front LEDs by pressing «C2» button on the DJI Remote controller. The Auto moving light will then be turned «ON/OFF» in sync with the aircraft’s front LEDs being turned ON/OFF.
MOUNT THE TUNDRA DRONE SIREN HERDER UNIT ON THE AIRCRAFT AND PREPARE FOR
TAKEOFF
Be sure that the drone is turned OFF before mounting the Tundra Drone Siren
herder on the aircraft. Follow the mounting instructions below. 
Release the Velcro holding the rubber band for
3-point mounting mechanism.
Pull out the rubber band in full length to the right. 
Lift the drone’s front arm and place
the released rubber band over one of the drone propeller arms, as shown in the
illustration above.
- Be careful not to damage the propeller when mounting the unit. Remove the propeller if needed.
Pull out the rubber band in full length to the left side. Lift the drone´s left front arm and place the released rubber band over the drone propeller arm, as shown in the illustration.
- Be careful not to damage the propeller when mounting the unit. Remove the propeller if needed.
Place the released rubber band over the left drone propeller arm, as shown in
the illustration. 
Place the
Tundra Drone Siren herder’s bottom edge against the drone roof’s edge.
Tighten the rubber band on both sides
by pulling full length of the rubber band towards the cord lock. 
Tighten the rubber band and use the
cord lock to lock the rubber band in place. Make sure the rubber band is tight
on both sides and ensure it cannot move in any direction. 
Use the Velcro to securely fasten the rubber band in
place. 
Find the Siren
activator module.
- The design of the Siren activator module may vary depending by the aircraft model.
Release the Velcro band on the Siren activator module. Place the Siren
activator module next to the drone’s front leg. Lift the drone’s front leg and
place the Siren activator module at the bottom.
Slide the Siren activator module upwards.
Slide it upwards until it covers the drone’s front LED. 
Connect the Siren activator module to
the Siren herder´s USB-C port.
- Do NOT connect the Siren activator module to the USB-C port before you have slid it over the drone’s front LED. The Siren herder may be activated and produce a loud siren sound if it’s exposed to light. This could harm your hearing. If this happens, unplug the Siren activator module from the USB-C port immediately!
The Siren activator module is now connected the USB-C port. 
Release the Velcro band.
Fasten the velcro band and make sure it holds the
cable tight against the drone’s propeller arm. Make sure the propeller does
not get in touch with the cable or any other objects. 
After securing the cable with the Velcro, the
propeller should be able to spin around freely without touching the cable or
other objects.
Ensure the
propeller can spin freely above and around without touching the cable or
anything other objects.
- Do NOT turn on the drone while doing this procedure!
If the propeller can spin freely, you are ready to fly!
- If the propeller cannot spin around freely or is touching any objects or cables, please repeat the steps above until the propeller can spin freely around without touching any objects.
Your aircraft is now ready for take-off with the Tundra Drone Siren herder.
Fly safely!
HOW TO UNMOUNT AND STORE THE TUNDRA DRONE SIREN HERDER
- Turn off your drone. Remove propellars if needed.
- Follow the “How to use the DJI Remote controller with the Tundra Drone Siren herder” procedure in reversed order to unmount the unit from the aircraft.
- Fully charge your battery (approx. 2 hours) before you store it for a longer period of time.
- Store your Tundra Drone Siren herder and the Siren activator module in a protected storage space. Store it in a calm and dry environment. Do not place the device where it can be exposed to excessive heat or a dusty enviroment.
SUPPORT
For support please contact us by email
mail@tundradrone.com or visit our website
tundradrone.com
References
- Tundra Drone | World's Brightest Automoving Drone Light
- Support | Tundra Drone
- Tundra Drone | World's Brightest Automoving Drone Light
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>