FISHER AND PAYKEL OB24SMPTDG1 Built in Oven Owner’s Manual

FISHER AND PAYKEL OB24SMPTDG1 Built-in Oven

Specifications :

• Product: Built-in Oven
• Models: MINIMAL OB24SMPTDG1, OB24SMPTNG1, OB24SMPTDB1,  OB24SMPTNB1, OB24SM16PLG1, OB24SM16PLB1, CONTEMPORARY OB24SDPTDX2, OB24SD16PLX1, OB24SD11PLX1
• Installation Guide : US CA

Product Usage Instructions

Electrical Requirements:

Before installing the oven, be sure to follow these electrical requirements:

• Connect the oven with copper wire only.
• Do not cut the conduit.
• A U.L.-listed conduit connector must be provided at the junction box.
• Do not ground to a gas pipe.
• Do not have a fuse in the grounding or neutral circuit.
• Fuse both sides of the line.
• A time delay fuse or circuit breaker is recommended. If using a time delay fuse, then fuse both sides of the line.
• Flexible armored cable from the appliance should be connected directly to the junction box.
• Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire).
• If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path and wire gauge are in accordance with local codes.

Prior to Installation:

Before installing the oven, ensure the following:

• Protect surrounding cabinetry from condensation by moisture-proofing the oven cavity.

After Installation:

After installation, make sure to:

• Ensure the oven door can open fully without obstruction.
• Avoid sealing the oven into the cabinetry with silicone or glue to facilitate future servicing.
• Ensure the power supply cable does not touch any hot metal parts.
• Check that the isolating switch is easily accessible to the customer with the oven installed.
• Complete the ‘Final checklist’ at the end of the installation process.

FAQ:

• Q: What should I do if correct performance cannot be achieved after installation?
  • A: If you are experiencing issues with your oven performance after installation, please contact your nearest Fisher & Paykel trained and supported service technician, Customer Care, or visit our website at fisherpaykel.com for assistance.

SAFETY AND WARNINGS

WARNING!

To avoid hazard, follow these instructions carefully before installing or using this appliance.

• Please make this information available to the person installing the appliance—doing so could reduce your installation costs.
• Save these instructions for the local inspectors use.
• This oven is to be installed and connected to the electricity supply only by an authorized person.
• If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the socket cable section is suitable for the electricity drawn by the oven.
• The oven must be grounded.
• Installation must comply with your local building and electricity regulations.
• This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations. Failure to install the appliance correctly could invalidate any warranty or liability claims.
• If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
• A circuit breaker is recommended.
• Do not use adaptors, reducers or branching devices to connect the oven to the mains electricity supply, as they can cause overheating and burning.
• The appliance must not be installed behind a decorative door in order to avoid overheating.
• Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction.

The manufacturer does not accept any responsibility for damage resulting from incorrect installation

Electrical requirements

• Connect oven with copper wire only.
• Do not cut the conduit.
• A U.L.-listed conduit connector must be provided at the junction box.
• Do not ground to a gas pipe.
• Do not have a fuse in the grounding or neutral circuit.
• Fuse both sides of the line.
• A time delay fuse or circuit breaker is recommended. If using a time delay fuse, then fuse both sides of the line.
• Flexible armored cable from the appliance should be connected directly to the junction box.
• Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire).
• If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path and wire gauge are in accordance with local codes.

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

PRIOR TO INSTALLATION

Ensure that:

• The countertop and oven cavity are square and level and are the required dimensions.
• The installation will comply with all clearance requirements and applicable standards and regulations.
• The isolating switch will be easily accessible to the customer with the oven installed.
• The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 meters in front of the bottom edge of the opening.
• The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
• The oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
• The oven will rest on a surface that can support its weight.
• The height from the floor suits the customer.
• You consult local building authorities and by-laws if in doubt regarding installation.

IMPORTANT!

Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture- proofing the oven cavity

AFTER INSTALLATION

Ensure that:

• the oven door can open fully without obstruction
• the oven is not sealed into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal
• the power supply cable does not touch any hot metal parts
• the isolating switch is easily accessible to the customer with the oven installed
• you complete the ‘Final checklist’ at the end of the installation If, after following the guidance given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel trained and supported service technician, Customer Care, or contact us through our website fisherpaykel.com

INSTALLATION MILESTONES

These milestones represent areas throughout that are pivotal to an optimal installation outcome. These steps require additional installer attention and should be quality-checked once completed.

MILESTONE LINKS

• Ensure both hinges are fully locked before shutting the door.
• Align oven with surrounding cabinetry and appliances.

PARTS

Supplied

TOOLS

Not supplied

PRODUCT DIMENSIONS

INDICATES PRODUCT DATUM ——————————————-
INDICATES CABINETRY CLEARANCES ——————————–

CABINETRY DIMENSIONS

If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manufacturer’s instructions.

PROUD INSTALL

FLUSH INSTALL

CHECK CAVITY

1. Measure cavity dimensions. Ensure all minimum specifications have been met.
2. For dark cabinetry, ensure clashing has been considered and installed.
3. Ensure service access complies with local requirements.
4. Ensure any cooktop ventilation requirements have been considered.

UNPACK PRODUCT

• Do not lift or move the product using the handle.
• Keep all packing materials until the unit has been inspected.
• Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you brought the product from to report the damage.
• Fisher & Paykel is not responsible for shipping damage.

1. Cut all straps and remove the carton top cap.
2. Lift the carton sleeve and remove any transit packaging.
3. Set aside any accessories.
4. Dispose responsibly.

REMOVE DOOR

1. Open the door and remove all cable ties and packaging holding the oven shelves in place.
2. Grip the shelves at the front, making sure to hold the wire shelf and frame together. Lift upwards and pull out from the oven.
3. Locate the hinge locks on either side of the door. Push the locks upwards to release.
4. Holding the door on both sides, partially close the door and carefully pull the door away from the hinges.

CONNECT POWER

• This oven must be connected to the mains power supply only by a suitably qualified person.
• This oven must be earthed

Before connecting the oven to the mains power supply, check that:

the domestic wiring system is suitable for the power drawn by the oven (as specified on the rating plate)
the voltage corresponds to the value given on the rating plate.

THREE WIRE CONNECTION

1. Disconnect the power supply and 1 remove the junction box cover.
2. Connect the oven cable to the junction box through the U.L-listed conduit connector.
3. Connect the two black wires together with twist-on connectors and the two red wires together with twist-on connectors.
4. Connect electrical connections according to local codes and ordinances.

If local codes DO NOT PERMIT connecting the cabinet-grounding conductor to the neutral (white) wire in the junction box.

1. Separate the factory-taped green and white oven cable wires. If the junction box is grounded, connect the green wire to the metal junction box with a screw before connecting the white oven cable wire to the neutral (white) wire in juction box.
2. Replace the junction box cover

If local codes permit connecting the cabinet-grounding conductor to the neutral (white) wire in the junction box.

1. Connect the factory-taped gree and white oven wires to the neutral (white) 1 wire in the junction box.
2. Replace the junction box cover.

FOUR WIRE CONNECTION

1. Disconnect the power supply and remove the junction box cover.
2. Connect the oven cable to the junction box through the U.L – listed conduit connector.
3. Connect the two black wires together with twist-on connectors and the two red wires together with twist-on connectors.
4. Connect electrical connections according to local codes and ordinances.
5. Separate the green and white oven cable wires. Connect the white oven cable wire to the neutral (white) wire in the junction box.
6. Connect the green grounding oven cable wire to the (green) grounding wire in the junction box. Do not connect the green grounding wire to the neutral (white) wire in the junction box.
7. Replace the junction box cover.

POSITION OVEN INTO CAVITY

1. Some models only: For dark cabinetry, the supplied trim can be used to enhance the clashing finish. To install, remove the trim adhesive and press to secure to cavity.
2. Lift product into cavity.

REFIT DOOR

1. Holding the door on both sides, carefully lift door back onto the hinges.
2. Open the door fully and push each locking lever down and lock into place
3. Ensure both hinges are fully locked before shutting the door.

ALIGN AND SECURE

1. Align oven with surrounding cabinetry and appliances.
2. Using the product as a guide, pre-drill 2 x 3mm pilot holes.
3. Secure oven to cavity using the 2 x #7×13 pan head screws provided.

REFIT SHELVES

1. Sliding shelves

   • Place shelves back into the oven at the desired level.
     Ensure shelves are level and correctly positioned with the guard rail at the back.

2. Wire Shelves
   Slide shelves into the cavity

3. Clip-on sliding shelf supports
   Ensure the slides are positioned the correct way around, with the triangular tab at the front.
   Fit the top clips over the side rack. The front clip should be fitted as close to the front of the side rack as possible. Make sure the rear clip has engaged.
   Click the bottom clips into place.

TEST OVEN

Follow the guidance on the screen to ensure the oven turns on and heats correctly. Refer to your User Guide for more information.

INSTALLER CHECKLIST

• Ensure the oven is level and securely fitted to the cabinetry.
• Check the lower trim is undamaged.
• Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim.
• This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
• Ensure you remove all internal packaging (including the circular yellow packing retainers holding the accessory box in place).
• Ensure all oven vents and openings are clear and free of any obstruction or damage.

Failure to make sure all oven vents are clear may result in poor product performance.

Ensure the isolating switch is accessible by the customer.

Complete and keep for safe reference:

Model………….
Serial No…………..
Purchase Date………..
Purchaser…………
Dealer Address…………
Installer’s Name………….
Installer’s Signature…………
Installation Company…………
Installation Date………………..

FISHERPAYKEL.COM

© Fisher & Paykel Appliances 2024. All rights reserved.
The models shown in this guide may not be available in all markets and are subject to change at any time.

The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.

For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer.

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>