tp-link RJ45 SFP Module Installation Guide

tp-link RJ45 SFP Module

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com/business to join TP-Link Community.
Note : Images may differ from the actual products.

Installing the RJ45 SFP / RJ45 SFP+ Module

1. Lock the yellow latch into place and insert the module into an SFP / SFP+ slot with label side up.
2. Gently push the module into the slot until you hear a click. Then, insert the RJ45 network cable.

Removing the RJ45 SFP / RJ45 SFP+ Module

1. Press the RJ45 crystal head and pull out the cable.
2. Pull down the latch and remove the module.

Positioning the 10G RJ45 SFP+ Modules

The 10G RJ45 SFP+ modules consume more power than optical modules. This may result in higher heat. To avoid overheating, it is recommended to place the modules separated by multiple optical transceivers or empty slots. When used in high temperature environments, additional cooling must be applied.The figures below only show the recommended positioning. The actual number of modules that can be inserted depends on the switch’s heat dissipation and power margin.

Scenario 1:

Scenario 2:

Specifications

General Specifications

IEEE802.3i
IEEEE 802.3u
IEEEE 802.3ab
IEEEE 802.3x
SFF-8472
INF 8074/SFP MSA| IEEE 802.3
IEEEE 802.3ab
IEEE 802.3bz
IEEE 802.3an
SFF-8472
SFF-8431
| |
MAC Interface| 1000BASE-X| 1000Mbps: 1000BASE-X
---|---|---
Data Rate* (max.)| 1.25 Gbps| 10.3125 Gbps
Power Consumption (max.)| 0.8 W| 2.5 W

Cable Distance

| 10Base-T: UTP

category 3, 4, 5 cable

(maximum 100 m) 100BASE-TX: UTP

cat.5 or above (max. 100m)

1000BASE-T: UTP

cat.5e or above (max. 100m)

| 1000BASE-T/2.5GBASE-T/ 5GBASE-T: UTP cat.5e or above (max. 100m) 10GBASE-T: UTP cat.6a or

above (max. 30m)

RX_LOS| /| /
TX_Fault| /| /
TX_Disable| Yes| Yes
Hot Swappable| Yes| Yes
LLF| /| /
LFP| /| /
Environmental and Physical Specifications|
---|---
Product Operating Temperature| 0˚C to 70˚C (32˚F to 158˚F)|
Storage Temperature| -40˚C to 85˚C (-40˚F to 185˚F)|
Operating Humidity| 10% to 90% RH, Non-condensing|
Storage Humidity| 5% to 90% RH, Non-condensing
---|---
Compatiblity|
---|---
Model| SM331T| SM5310-T
Gigabit SFP Slot (SFP Slot)| Supported| Supported*
10G SFP+ Slot (SFP+ Slot)| Supported*| Supported

We recommend that you use only TP-Link modules on your TP-Link devices. To check the compatible TP-Link devices of your module, please visit our website.

Note:

• SM5310-T does not support the data rate of 10 Mbps or 100 Mbps.
• When a gigabit RJ45 SFP module is inserted into a 10G SFP+ slot, extra configuration for port data rate may be required.
• When a 10G RJ45 SFP+ module is used at 1 Gbps, extra configuration for port data rate may be required. And when it is inserted into a 10 Gbps SFP+ slot and the maximum rate of the peer connection port is 5 Gbps or 2.5 Gbps, the flow control for the 10 Gbps SFP+ slot needs to be manually enabled.

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
• This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at
https://www.tp-link.com/en/support/ce.

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016. The original UK Declaration of Conformity may be found at
https://www.tp-link.com/support/ukca

Explanation of the symbols on the product label
Symbols may vary from products . The label is at the bottom of the product.

FCC compliance information statement

Product Name : Omada 1000BASE-T RJ45 SFP Module/Omada 10GBASE-T RJ45 SFP+ Module
Model Number : SM331T/SM5310-T
Responsible party:
TP-Link USA Corporation
Address : 10 Mauchly, Irvine, CA 92618
Website:https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail:sales.usa@tp-link.com

References

• Link: Simple, secure one-click payments
• CE Regulatory Compliance | TP-Link
• TP-Link Product Support - Wireless Networking Equipment Support
• Regulatory Compliance | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>