COREMORROW E63.A1K Series Piezo Controller User Manual
- June 3, 2024
- COREMORROW
Table of Contents
COREMORROW E63.A1K Series Piezo Controller
Introduction
Features
- Super small size
- Low power consumption 15V (±0.5V) power supply Peak current 100mA
- Ave current 12mA
- Unload bandwidth 1KHz Output short circuit protection
Applications
- Driving piezo actuators
Order information
- E63.A1K——1Channel Open loop
- Accept customized according to requirements：
- 12bit gain/-20 ～ 120V output voltage（default）
- 15bit gain/-20 ～ 150V output voltage
Driving Principle
Appearance
4. Pin Definition
| Pin No. | Functions |
|---|---|
| 1 | Power supply: +15VDC/0.5A |
| 2 | Supply voltage ground and control input ground, AGND |
| 3 | Analog voltage input |
| 4 | Voltage output ground: SGND output |
| 5 | Analog voltage output |
| Housing | Shielding ground GND |
Notes and suggestions
- E63.A1K cannot be used to drive inductive loads. If the inductive loads are driven, the product may be damaged.
- The highest output voltage of E63.A1K will decrease with the increase of output current, so please pay attention to it when using. The drawdown curve is as follows:
Customer Service
If you have any questions in use, please tell us the following information:
- Product model and relevant number The controller model
- Software driver version
- Supporting computer operating system
Contact us
- Harbin Core Tomorrow Science & Technology Co., Ltd.
- Tel: +86-451-86268790
- Email: info@coremorrow.com
- Website: www.coremorrow.com
- Address: Building I2, No.191 Xuefu Road, Nangang District, Harbin, HLJ, China
- CoreMorrow Official and CTO WeChat are below:
DECLARATION
Declaration!
This user manual is an integrated user manual of the E63.A1K series
piezoelectric controller. Please read this user manual carefully before using
this controller. Follow the instructions in the manual during use. If there is
any problem, please contact us for technical support. If you do not follow
this manual or disassemble and modify the product yourself, the company will
not be liable for any consequences arising therefrom.
Please read the following to avoid personal injury and to prevent damage to
this product or any other product connected to it. In order to avoid possible
hazards, this product can only be used within the specified range.
Notice!
- Do not touch any exposed ends of the product and its accessories.
- There is a high voltage inside. Do not open the case without permission.
- Do not connect or disconnect input, output, or sensor cables with power on.
- Please keep the surface of E63.A1K clean and dry, don’t operate in a humid or static environment.
- After use, the output voltage should be cleared to zero before turning off the controller switch, such as switching the servo state to the open-loop state.
Danger!
The piezoelectric power amplifier described in this manual is a high-voltage
device capable of outputting high currents, which can cause serious or even
fatal damage if not used properly.
It is strongly recommended that you do not touch any parts that connect to the
high-voltage output. Special Note: If you connect it with other products in
addition to our company, please follow the general accident prevention
procedures.
Operating high-voltage amplification requires training professional operators.
Warning!
If the voltage exceeds the PZT’s tolerable range, it will cause permanent damage to the PZT. Before adding voltage to the PZT poles, it must be ensured that the positive and negative poles of the PZT are connected correctly and the operating voltage is within the allowable range of this PZT.
Cautious!
E63.A1K housing should be installed on a horizontal surface in an area with a
3CM air flow area to prevent internal convection in the vertical direction.
Insufficient airflow can cause equipment to overheat or premature instrument
damage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>