circle CIM315C Compact Contactless Smart Card Reader Module User Manual

June 5, 2024
circle

circle CIM315C Compact Contactless Smart Card Reader Module

Driver installation Procedure

The driver is signed by Microsoft and WHQL, user can install the driver with Window Update. In case that cannot install via Window Update, please process the below steps to Manual installation.

Hardware requires:

  • CIM315C
  • PC with OS Windows 7 or above

Software requires:

  • CIR315 Driver Package

Steps:

  1. Connect CIM315C to PC
  2.  On PC, open “Control Panel > System”
  3. Open “Device Manage
  4. Select and open “Smart card readers”if it is shown “Microsoft Usbccid … (WUDF)”, please continue with step 5)
  5. if it is shown “CIR315 CL”, mean driver install completed Right click then select “Update driver” (one by one)
  6. Select “Browse my computer for driver software
  7. Let me pick from a list
  8. Select “Have Disk…”
  9. Select “Browse…”Select “CIR315.inf”, then press “Open” and “OK”
  10. Select “CIR315 CL” then “Next”
  11. Waiting until below screen shown, Press “Close” to complete
  12. Double click to ensure the device changed to “CIR315 PICC” and “CIR315 SAM”
  13. Done

Operation Example

Hardware requires:

  •  CIM315C
  •  PC with OS Windows 7 or above
  •  ISO14443 Test Card

Software requires:

  • Any PCSC Application (e.g. APDU.exe)

Steps:

  1. Plugin the reader into the PC
  2. Open “APDU.exe”
  3. Click “1. Select reader”, Chose “Circle CIR315 CL 0”, then click “OK”
  4. Tag ISO14443 Test card on CIM315C
  5. Select “T1”, Message = “90 0a 00 00 01 00 00”
  6. Press “2. Connect”
  7. Press “3. Transmit”
  8. Result will be shown on the “Answer from the card:

FCC Statment

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

Caution
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Specific operational use conditions
The end product which used the equipment have to full test and apply an original FCC ID. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Limited modular
This equipment applied as Limited single-modular transmitter, the end product which used this equipment have to full test and apply an original FCC ID.

RF Exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end product which used this equipment have to full test and apply an original FCC ID.

Antennas
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. The end product which used this equipment have to full test and apply an original FCC ID.

Label and compliance information
The end product which used this equipment have to full test and apply an original FCC ID. Label should be included and compliance to the FCC rules with end product’s FCCID.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals