Circutor eNext M255A01-41 Recharge Box User Manual
- July 9, 2024
- Circutor
Table of Contents
Circutor eNext M255A01-41 Recharge Box
Specifications
- Power supply: AC
- Input voltage: 1000V
- Output current: 32 A
- Output power: 7.4 kW, 22 kW
- Frequency: 50 Hz / 60 Hz
- User interface: CirBEON-63
- Connectivity: Wireless communication (BLE)
- Operating temperature: Not specified
- Relative humidity: Not specified
- Protection degree IP: Not specified
- Mechanical features: Weight – 4 kg, Enclosure – PC + GF 10%
Product Usage Instructions
- Installation
- Before installation, ensure the device is disconnected from all power sources. Contact after-sales service if there are any operational faults.
- Connection
- Connect the device according to the provided diagram and instructions in the manual. Ensure proper grounding by connecting the ground cable to the designated terminal.
- Operation
- Once installed and connected, follow the user interface instructions provided on the CirBEON-63 interface for charging electric vehicles.
- Maintenance
- Regularly check for any loose connections or signs of wear. Refer to the manual for troubleshooting steps in case of malfunctions.
FAQs
- Q: What should I do if the device malfunctions?
- A: Contact the after-sales service for assistance. The device is designed for easy replacement in case of malfunction.
- Q: Can I use non-original accessories with the device?
- A: The manufacturer recommends using only original products or accessories made by authorized manufacturers to avoid damage.
- Q: Is the device compatible with all electric vehicles?
- A: The device is designed to charge electric vehicles as specified by IEC 61851 standards. Ensure compatibility with your vehicle before use.
PRODUCT INFORMATION
This manual is an exact installation guide. For further information, please download the full manual from the CIRCUTOR website: www.circutor.com.
| IMPORTANT!
---|---
The device must be disconnected from its power supply sources (power supply
and measurement) before undertaking any installation, repair, or handling
operations on the device’s connections. Contact the after-sales service if you
suspect that there is an operational fault in the device The device has been
designed for easy replacement in case of malfunction.
The manufacturer of the device is not responsible for any damage resulting
from failure by the user or in-staller to heed the warnings and/or
recommendations set out in this manual, nor for damage resulting from the use
of non-original products or accessories or those made by other manufacturers.
DESCRIPTION
- eNext is a Charge Point that has been designed and tested to allow charging electric vehicles, vehicles, as specified at IEC 61851 standards.
INSTALLATION
Dimensions
Personal protective equipment
What’s included
Minimum distances
Technical features
REMOTE CONTROL
- Remove jumper J7 to enable this function
- Note: Device images are for illustrative purposes only and may differ from the actual device.
WIRING
Note: If a feedback connection is preferred, please refer to the installation manual.
Use the provided cable glands
Single Phase: 230 V~
- Three Phase: 400 V~
- If single Phase: L1+N
- Main Circuit section: 6(3)/10 mm2 (≤ 10 mm2)
- Auxiliar Circuit section: 2.5 mm2 (≤ 4 mm2)
- Trip Coil section: 2.5 mm2 (≤ 4 mm2)
- Do not forget to connect the ground cable to the ground terminal.
- Type of cable: Copper
- Make sure all screws are securely tightened: 1.5 Nm
CirBEON-63 Single Phase
CLOSING SEQUENCE
Technical service
- CIRCUTOR SAT: 902 449 459 (SPAIN) / (+34) 937 452 919 (out of Spain)
- Vial Sant Jordi, s/n
- 08232 – Viladecavalls (Barcelona)
- Tel: (+34) 937 452 900 –
- Fax: (+34) 937 452 914
- e-mail: sat@circutor.com.
References
- Productos y soluciones integrales para la eficiencia energética eléctrica
- Productos y soluciones integrales para la eficiencia energética eléctrica
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>