KOHLER Rite-Temp K-8304-PS Valve Body and Cartridge Kit Complete Owner’s Manual
- July 6, 2024
- Kohler
Table of Contents
KOHLER Rite-Temp K-8304-PS Valve Body and Cartridge Kit Complete
Specifications
- Product: Valve Body & Cartridge Kit Complete K-8304-PS
- Material: High-quality material for long-term reliability and resistance to aggressive water conditions
- Max Finished Wall: 1-15/16 (49 mm)
- Min Finished Wall: 1-15/16 (49 mm)
- Outlet Port: 1/2-14 NPT and 5/8 ID for 1/2 Nominal Copper Tubing
- Pressure:
- Maximum (Static) Pressure: 125 psi (8.6 bar)
- Minimum (Operating) Pressure: 20 psi (1.4 bar)
Features
- Includes valve body, pressure balance cartridge, rough-in guide, and mudguard
- 1/2″ PEX Crimp (F1807 style) inlets, with stops
- 1/2″ Universal NPT & direct sweat outlets
- Service stops include integral check valves
- 5 gpm (18.9 l/min) maximum flow rate at 45 psi
- ingle lever design cycles from off through cold to hot
- Anti-scald protection
- One-piece cartridge design simplifies installation and maintenance
- Adjustable high-temperature limit stop to control maximum water temperature
- Requires valve trim to complete installation (sold separately)
- Pressure-balancing diaphragm technology maintains outlet temperature within +/-3°F during water pressure fluctuations
Material
- Forged dezincification-resistant brass body provides long term reliability and resistance to aggressive water conditions
Installation
- Designed for use in standard, back-to-back and thin wall installations
- Valve body features integral mounting locations and symmetrical valve inlets to simplify installation
- Cartridge is reversible for installations where hot and cold supplies are reversed
- Rough-in guide designed for both standard and thin wall installations
- Installed valve rough-in can be flushed and pressure-tested to 150 psi max (air or water) without cartridge by using test cap (sold separately)
Optional Products/Accessories
- K-10350 Deep rough-in kit
- K-10351 Test cap for K-8300 Series valve bodies
Codes/Standards
- ASME A112.18.1/CSA B125.1
- ASSE 1016/ASME A112.1016/CSA B125.16 IAPMO Certification
KOHLER® Faucet Lifetime Limited Warranty
See website for detailed warranty information.
DIMENSION
Technical Information
All product dimensions are nominal.
Shower Valve:
- Pressure: 45 psi (3.1 bar)
- Maximum (Static) Pressure: 125 psi (8.6 bar)
- Minimum (Operating) Pressure: 20 psi (1.4 bar)
Notes
- Install this product according to the installation guide.
- Avoid cross-flow conditions. Do not install shut-off device on either valve outlet.
- Cap the shower outlet if the deck-mounted spout, diverter, or handshower is connected to the spout outlet.
- Install straight pipe or tube drop of 7″ (178 mm) to 18″ (457 mm) with single elbow between the valve and wall-mount spout.
- For finished walls greater than 3/4″ (19 mm) and less than 1-1/2″ (38 mm), install support(s) 2″ (51 mm) from the stud face.
- For finished walls greater than 1-1/2″ (38 mm), install support(s) 3″ (76 mm) from the face of the finished wall.
MORE INFORMATION
- 1-800-4KOHLER (1-800-456-4537)
- Kohler Co. reserves the right to make revisions without notice to product specifications.
- For the most current Specification Sheet, go to www.kohler.com USA or www.kohler.ca Canada 6-7-2024 21:42 – US
FAQ
- Q: What is the maximum pressure this product can handle?
- A: The product can handle a maximum static pressure of 125 psi (8.6 bar).
- Q: What materials are used to ensure reliability?
- A: The product is made of high-quality materials known for long-term reliability and resistance to aggressive water conditions.
References
- Toilets, Showers, Sinks, Faucets and More for Bathroom & Kitchen | KOHLER
- Toilets, Showers, Sinks, Faucets and More for Bathroom & Kitchen | KOHLER
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>