zigbee Soil Temperature Humidity and Light Sensor User Guide

zigbee Soil Temperature Humidity and Light Sensor

Specifications

• Power supply: 2*AA battery (Do not use rechargeable battery)
• Battery life: > 1 year
• Working frequency: 2.4GHz
• Transmission distance: 100 meters
• Size: 49.931.3202.5mm
• Temperature measurement accuracy range
• Humidity measurement range: 0-100%RH
• Humidity measurement accuracy: 0.1%
• Light intensity range: 1-65535Lux
• Low temperature alarm (Only APP can display the alarm)
• Low power alarm (Only APP can display the alarm)
• IP rating: IP65

Product Usage Instructions

• Installation
  The humidity probes are all inserted into the soil. Dig a hole and bury the PCB part of the device into the soil.

Battery Installation

1. Unscrew the battery cover with a screwdriver.
2. Insert the batteries checking the polarities (+ / -) are correctly aligned.
3. Install the battery cover, then tighten with a screwdriver.
4. Complete.

Precautions

1. The battery cannot be replaced when the product is exposed to rain.
2. When using the product, insert the sensor chip into the soil completely.
3. Remember to put back the sealing ring after replacing the battery to maintain waterproofing.
4. Avoid rubbing the sensor sheet on the ground to prevent damage to the circuit board.

Data Refresh and Configuration
The data refresh time is fixed at 30 seconds. Pressing the configuration button on the device can refresh the sensor data immediately.

FAQ

• Q: What is the working frequency of the sensor?
  A: The sensor operates at a working frequency of 2.4GHz.

• Q: How do I replace the batteries?
  A: To replace the batteries, unscrew the battery cover, insert new batteries with correct polarity, and then tighten the cover with a screwdriver.

• Q: How do I configure the light sensor?
  A: The light sensor can be configured using the provided button on the device. Long-press for 5 seconds to reset and enter network distribution mode, short press to collect and report data immediately.

Zigbee soil temperature, humidity and light sensor
This sensor is a soil temperature, humidity and light data collector for the smart life APP. It adopts Zigbee technology and has a transmission rate of 250Kbps.
After connecting to the APP through the Zigbee gateway, it regularly uploads temperature, humidity and light data to mobile phones or cloud platforms for user reference.

Specification

enters the network distribution mode, and a short press immediately collects data and reports it.
LED display| After the device enters the network configuration mode, it will flash continuously for 30 seconds. After the network configuration is successful, it will light up for 1 second and then turn off. It will light up when the data is reported.
Temperature measurement range| -20~85°C (-4°F~-185°F)
---|---
Temperature measurement accuracy| 0.1°C
Humidity measurement range| 0-100%RH
Humidity measurement accuracy| 0.1%
Light intensity| 1-65535Lux
Low temperature alarm(Only APP can display the alarm )| ≤-15°C(5°F)
Low power alarm (Only APP can display the alarm )| ≤40%
Installation method| The humidity probes are all inserted into the soil
IP| IP 65

Battery installation

1. Unscrew the battery cover with a screwdriver.
2. Insert the batteries checking the polarities (+ / -) are correcly aligned.
3.  Install the battery cover, then tighten with screwdriver.
4. Complete.

Installation

• The humidity probes are all inserted into the soil.
• Tips : Please dig a hole and bury the PCB part of the device into the soil.

Precautions

1. The battery cannot be replaced when the product is exposed to rain. Prevent the internal moisture from damaging the components after the shell is opened.
2.  When using the product, insert the sensor chip into the soil to the end.
3. Don’t forget the sealing ring after replacing the battery, otherwise the waterproof effect may be weakened.
4. Do not rub the sensor sheet on the ground to damage the circuit board.
5.  The Zigbee soil temperature, humidity and sunlight sensor data refresh time is fixed at 30 seconds, and the configuration button on the device can refresh the sensor data immediately.

FCC Warning

FCC ID :2AOIF-981XRTH

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following. measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Note:

• The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
• The device has been evaluated to meet general RF exposure requirement.
• To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation.

Link APP

• Download:
  Click App store or Android application market to download “Tuya Smart ”app.

• Registration and Login :
  Click the “Register” to create account. Enter your account password to log in

Add gateway

1. Enter the “HOME” interface of the app ,Click the “+” in the upper right corner

2. Click the list bar “Gateway Control ”, select the Gateway (Zigbee) in the right device list
   Tips : if your gateway is wired, please click“ Gateway(Zigbee

3. Enter your wifi account and password. Click “ Confirm

4. Click“ Confirm the indicator is blinking

5. Click “ Blink Quickly”

6. Connecting device….

7. Click “Done”, it means the gateway added successfully.

Tips

• Before binding the gateway, you need to power on the gateway.
• When binding a gateway, the mobile phone and the gateway must connect to the same network.

Add a device through gateway

1. Press and hold the configuration button for 5 seconds. Wait for the red light to flash.
2. Click “Add subdevice ” to enter the device list.
3. Search device
4. Select the type of device you want to add
5. Click “Done”, it means the device added successfully

Tips
Gateway must be added before adding Zigbee soil sensor

• Zigbee soil temperature, humidity and light sensor operation interface
• Zigbee soil temperature, humidity and light sensor Setting interface
• Zigbee soil temperature, humidity and light sensor Smart interface
• Zigbee soil temperature, humidity and light sensor Device information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>