AMETA DR-ATM11B Drone User Manual

AMETA DR-ATM11B Drone User Manual

Land: When the drone hovers in the air without any obstacles, press and hold the   button for 1s to make it descend and land until the propellers stop rotating.

Circle Fly
If there are no obstacles within a radius of 5 meters around the drone, press and hold the button for 3s on the remote to make the drone fly in a circular pattern.

Press and hold the   button for 3s again to disable this function. To perform this function, the drone must have enough power.

Doodle fly

1. Open the App and navigate to the main page.
2. Tap on the “ ” (Doodle fly) icon and adjust the scale by sliding the scale bar. The default scale is set to 1:1.
3. Use your finger to draw a desired flight path on the blank area of the screen.
4. The drone will follow the trajectory path without changing its flight height, but the length of the trajectory will vary based on the selected scale
   
   

3D Flip

After flying the drone in an obstacle-free area, press the   button to activate the 360° flip function. Once activated, use the Right Control Stick to perform flips. Push the stick forward, backward, leftward, or rightward to execute a 360° flip in the corresponding direction.

To perform this function, the drone must have enough power.

Emergency Stop
If an abnormal situation occurs, you can simultaneously press and hold the button and   button on the remote for 3 seconds to make an emergency stop.

Please make an emergency stop when the drone’s flight height is below 9.8ft (3m). If the drone’s flight height is above 9.8ft (3m), carefully descend it to a height below 9.8ft (3m) before performing the emergency stop.

Notes
*When this function is activated, the drone’s motor and propellers will stop rotating, causing it to fall from the sky and potentially pose risks of damage. Use this function with caution.

• After an emergency stop, if you intend to fly the drone again, please reset the drone.
  

Throw to Go
Place the drone in your palm right side up, then toss it into the air at least 10cm high. The drone will automatically hover in the air.

Note
If the lights on the drone flash after a failed Throw to Go, reset the drone before retrying.

Light Mode Switch
Press and hold the   button to switch between 6 different light modes. To turn off the lights, simply press and hold the   button.

FN (Custom Function)

• Press the FN button for the first time: The drone will execute default flight actions. It is recommended to use this feature in an open area without obstacles for safety reasons.
• The drone will execute custom actions. Check the app for more details.
  

Headless Mode
Launch the app and tap the   button to activate this function. In this mode, the drone will fly following the direction of the Right Control Stick regardless of the position of your drone’s head or tail.

Throw to Go
Place the drone in your palm right side up, then toss it into the air at least 10cm high. The drone will automatically hover in the air.

Note
If the lights on the drone flash after a failed Throw to Go, reset the drone before retrying.

Light Mode Switch

Press and hold the   button to switch between 6 different light modes. To turn off the lights, simply press and hold the   button.

FN (Custom Function)

• Press the FN button for the first time: The drone will execute default flight actions. It is recommended to use this feature in an open area without obstacles for safety reasons.
• The drone will execute custom actions. Check the app for more details.
  

Headless Mode
Launch the app and tap the   button to activate this function. In this mode, the drone will fly following the direction of the Right Control Stick regardless of the position of your drone’s head or tail.

Tip:
The drone camera’s orientation is its “head” position. In headless mode, the direction is defined by the drone’s head orientation at takeoff.
Remembering the drone’s head orientation during takeoff will help you navigate accurately in headless mode.

Find Your Drone
When the drone is accidentally lost during flight, simultaneously press and hold the FN button and   button on the remote for 3 seconds to try to locate it. In response, the drone will emit rapid beeps. To exit this state, you can either repeat the above operation or briefly press the Power button on the drone.

To perform this function, the drone must be connected to the remote and have enough power.

Notes
* While this function is activated, you won’t be able to perform any other actions until you exit it.

• This function can only be activated after the drone has landed.

DRONE’S LIGHTS

strip
Reset| Lights form blue strip clockwise
Fail to execute commands or errors occur| Rapidly flash three times
Emergency Stop| Red and purple lights transition gradually
Low Battery| Lights flash slowly
Powering off| Colorful lights extinguish sequentially
Find Your Drone| Colorful lights cyclically flicker

BEEPS EXPLANATION

SPECIFICATIONS

Drone

(9.84ft/s)
Max. Flight Height| 15m (49.2ft)
Battery Capacity| 3.7V 850mAh Lithium Battery
Charging Time| ~60 minutes (depending on the power of the charger)
Transmit Power (EIRP)| <17dB

Camera

Remote

FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
   Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For Remote:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
For R/C QUADCOPTER:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISEDC Warning:

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

For Remote:
The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

The symbol indicates DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
This product can be used across EU member states.
EU Compliance Statement: Shenzhen Vento Technology & Innovation Co., Ltd. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
A copy of the EU Declaration of Conformity is available online at https://ametasmart.com/pages/eu-declaration-of-conformity

NA: support.na@ametasmart.com
EU: support.eu@ametasmart.com
NA: +1(800)-531-0915 (Mon-Fri)

ametasmart.com

@Ameta Official

@Ameta Official

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>