fiodio V3L6W 35 Inch Computer Monitor User Manual

fiodio V3L6W 35 Inch Computer Monitor

Model: V3L6W

Notices

Before using this product, please read this User Manual carefully and keep it well.

• Keep the monitor away from water sources or damp places, such as bathrooms, kitchens, basements, and swimming pools.
• If the monitor will not be used for a long period, please cut off the power supply to avoid electric shock on rainy days and damage due to abnormal supply voltage.
• Please use a reliable earthing socket, do not overload the socket, or it may cause fire or electric shock.
• Do not put foreign matters into the monitor, or it may cause short circuits resulting in fire or electric shock.
• Do not disassemble or repair this product by self to avoid electric shock. If faults occur, please contact the after-sales service directly.
• Do not pull or twist the power cable forcedly.
• There is a polarizer layer (not a protective film) on the surface of the screen. Do not peel it off, or the product may be damaged, and the warranty will be invalid.

Product Introduction

• The 35in Computer Monitor Model: V3L6W is a high-performance monitor designed for computer use.
• It features a large 35-inch display screen and comes with a stand and base for easy installation.

Product Packing List

Please check that the package of the monitor contains all parts. The color and shape of parts may vary with models. Figures in this User Manual are for reference only. Wires supplied may vary with purchased products. Figures in this User Manual are for reference only.

• Display screen
• Stand
• Base
• (PM4) Screws
• (KM4) Screws
• Power Cable
• DP cable
• User Manual

Note: The redundant screws are used as spare screws.

Product Instructions for Use

Description of Buttons

1. Menu button: Press to enter sub-menus.
2. Down button: Press to move down in the menu.
3. Up button: Press to move up in the menu.
4. Exit/hot key: Press to return to the previous menu.
5. Power button: Press to turn on/off the monitor.

Product Explanation of Indicators

Indicator light: A steady blue light indicates that the power is on, and the monitor is operating normally. Blue light flashes to indicate there is no video source, and no horizontal or vertical signal or low voltage is detected. Make sure your computer is turned on, and all video cables are fully plugged in and/or connected.

Adjusting the Monitor

To adjust the monitor, use the Menu button to enter sub-menus and the Up and Down buttons to navigate through the options. Use the Exit/hot key to return to the previous menu.

Product Installation of Base

To install the base, follow these steps:

1. Unpack the carton, remove the foam, and lay the monitor flat on the table. Keep the foam under the monitor until you install the stand.
2. Take out the base and bracket and tighten them with screws. Take out the shaft assembly and lock it with the base of the bracket with screws.
   • Tighten with two screws
   • Tighten with three screws
3. Remove the upper foam cover (note: the machine cannot leave the lower foam cover).
4. Use the assembled base bracket assembly to align the slot of the machine and buckle down (note: press and hold the quick release button with your fingers to take out the base bracket assembly).

Precautions

Notices

• Keep the monitor away from water sources or damp places, such as bath rooms, kitchens, basements and swimming pools.
• Make sure the monitor is placed on a flat surface. If the monitor falls down, it may cause human injury or device damage.
• Store and use the monitor in a cool, dry and well ventilated place, and keep it away from emission and heat sources.
• Do not cover or block the vent hole in the rear casing, and do not use the product on a bed, sofa, blanket or similar objects.
• The range of the supply voltage of the monitor is printed on the label on the rear casing. If it is impossible to determine the supply voltage, please consult the distributor or local power company.
• If the monitor will not be used for long period, please cut off the power supply to avoid electric shock in rainy days and damage due to abnormal supply voltage.
• Please use a reliable earthing socket, do not overload the socket, it or it may cause fire or electric shock.
• Do not put foreign matters into the monitor, or it may cause short circuits resulting fire or electric shock.
• Do not disassemble or repair this product by self to avoid electric shock. If faults occur, please contact the after-sales service directly.
• Do not pull or twist the power cable forcedly.
• There is a polarizer layer (not a protective film) on the surface of the screen. Do not peel it off, or the product may be damaged and the warranty will be invalid.

Product introduction

Packing list

• Please check that the package of the monitor contains all parts.
• The color and shape of parts may vary with models. Figures in this User Manual are for reference only.
• Wires supplied may vary with purchased products. Figures in this User Manual are for reference only.

Note: The redundant screws are used as spare screws.

Instructions for use

Description of buttons

1. M. Menu button: Press to enter sub-menus.
2. Down button: Press to move down in the menu.
3. Up button: Press to move up in the menu.
4. E. Exit/hot key: Press to return to the previous menu.
5. Power button: Press to turn on/off the monitor.

Explanation of indicators

Indicator light

A steady blue light indicates that the power is on and the monitor is operating normally. Blue light flashes to indicate There is no video source and no horizontal or vertical signal or low voltage is detected. Make sure your computer is turned on and all video cables are fully plugged in and/or connected.

Adjusting the monitor

• Tilting angle
  • -5.0°(±2.0°)- +15°(±2.0°)

Installation of base

Unpack the carton, remove the foam, and lay the monitor flat on the table.
Keep the foam under the monitor until you install the stand.

1. Take out the base and bracket and tighten them with screws.
   • Take out the shaft assembly and lock it with the base of the bracket with screws.
2. Remove the upper foam cover (note: the machine cannot leave the lower foam cover).
   • Use the assembled base bracket assembly to align the slot of the machine and buckle down.
   • ( note: press and hold the quick release button with your fingers to take out the base bracket assembly).
3. Press and hold the quick release button with your fingers to remove the base stand assembly.
4. After assembly, simply hold the stand with hand to stand the monitor upright.

Note: During standing of the whole monitor, do not press the liquid crystal screen with hand to avoid damage to the screen.

Installation of mount

1. Open the carton package, take out the foam and put it flat on the table top.
2. Remove the upper foam box, take out the film-coated bag of the fuselage, and put the fuselage into theoriginal lower foam box again.
3. Find the PM4*16 screws from the accessory kit, and lock the screws and wall-mounted components in the threaded holes of the rear shell.
   • when disassembling the wall-mounted components, the monitor cannot leave the foam box to prevent the screen from cracking.
4. Note: Hang the assembled product on a hard wall. Do not pinch the screen with your hands during the hanging process to avoid damaging the screen.

Notes

• To prevent the monitor on the mount from failing, please install it firmly and protect it fully.
• Do not place or hang any object on the mount, and the using height of the mount should be less than 2 meters.

Cable connection

• The bottom interface configuration at the back of the monitor varie with products.
• Note: If the power cable or signal cable is damaged, you must replace it with special soft cables or special components purchased from the manufacturer or maintenance department.

HDMI interface

• Use the HDMI cable to connect the HDMI IN interface of the product to the HDMI OUT interface of a PC.
• Use the HDMI-DVI cable to connect the HDMI IN interface of the product to the DVI OUT interface of a PC.

DP interface

• Use the DP cable to connect the DP IN interface of the product to the DP OUT interfac of a PC.

AUDIO OUT

• Connect audio outputting devices such as earphones to the AUDIO OUT interface.

AC interface

• Please connect the power cable plug to the corresponding port of the monitor, and connect the other end to a properly grounded power outlet.

OSD menu

Menu description

OSD menu

• The color and shape of the OSD menu of the actual computer may be slightly different from those shown in the figure.
• Specifications of the OSD menu may change with improvements of functions without prior notice.

The screen display (OSD) menu can be used to adjust settings of the monitor and is shown on the screen after the monitor is powered on and the button is pressed.

1. Press one of the buttons ( M, , , E, ) to activate the browser screen.
2. Press M ( ) to enter the OSD screen.
3. Press or to browse through the functions.
   • Select the desired function, then press the M button to enter the submenu
   • Press or to browse the sub-menus, and then press the M key to confirm the selection of the desired function.
   • Press or to select an option, then press M to confirm the setting and exit the current menu.
4. Press to exit the menu interface

• Functions of the monitor vary with models, and the functions in this manual are for reference only.

Input Source

| DP1| None
---|---|---
DP2| None
HDMI1| None
HDMI2| None

Brightness/ Contrast

| Brightness| 0-100
Blacklevel| 0-100
Contrast| 0-100
DCR| On/Off

Color Setting

| Gamma| 1.8/2.0/2.2/2.4/2.6
Pictrue Mode| Standard/Photo/Movie/Game/FPS/RTS
Color Temperature| Warm/Cool/User
Low Blue Light| 0-100
Hue| 0-100
Saturation| 0-100

Picture Quality Setting

| Sharpness| 0-100
Response Time| Off/High/Middle/Low
Noise Reduction| Off/High/Middle/Low
Super Resoultion| Off/High/Middle/Low
Dynamic Luminous Control| On/Off

Display

| Aspect Ratio| Wide Screen/4:3/1:1/Auto
LedMode| Flicker/Normal/Off

Audio

| Mute| On/Off
Volume| 0-100
Audio Source| DP1/DP2/HDMI1/HDMI2

Multi-Window

| Multi-Window| Off/PIP Mode/PBP 2Win
Sub Win2 Input| DP1/DP2/HDMI1/HDMI2
PIP Size| Small/Medium/Large
PIP Position| TopRight/TopLeft/BottomRight/BottomLeft
Swap| None

OSD

| Language| English/简体中文/한국어/РУССКИЙ/Español/日本語/Francais
OSD H-Position| 0-100
OSD V-Position| 0-100
OSD Transparency| 0-100
OSD Time Out| 5-100
OSD Rotation| Normal/90/180/270

Other

| DP Version| DP1.1/DP1.2/DP1.4
Adaptive-Sync| On/Off
HDR| On/Off/Auto Detect
Reset| None

Basic parameters

Power specifications

| 100-240V~,50/60Hz,2.0A

The standard voltage and current may vary with countries, please refer to the

label at the back of the product.

Product Dimentions Normal base| Without base| 837.39 x377.93 x 120.79 mm/ approx. 6.78kg
With base| 837.39 x 484.85 x 245.11mm/ approx. 8.9 kg
Carton size| 928x202x483mm
Gross Weight| 10.5KG
Tilting angle| Forward titling: -5°±2° ;  Backward tilting : 15°±2°
Rotation angle| NA
Height angle| NA
Pivot angle| NA
Environmental conditions| Action| Temperature: 0°C~ 40°C (32°F ~ 104°F) Humidity: 10%~90% RH (non-condensing)
Storage| Temperature: -20°~ 60° (-4°F ~ 140°F)            Humidity: 5%~95% RH (non-condensing)

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

FCC STATEMENT

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. This device must accept any interference received,
3. including interference that may cause undesired operation.

CAN ICES-3 (B)/NMB-3(B)

Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>