resideo UV2400U2000 AirBRIGHT 2 Ultraviolet Air Purifier Installation Guide
- July 4, 2024
- resideo
Table of Contents
resideo UV2400U2000 AirBRIGHT 2 Ultraviolet Air Purifier
Specifications
- Model: UV2400U2000 AirBRIGHT 2
- Size and Weight:
- Power Module: 4.75 L x 3.16 W x 1.75 H
- Mounting Bracket (Magnetic): 3.5 L x 2.25 W x 3.5 H
- Weight: 2 lbs.
- Electrical:
- Power: 24VAC (Expanded range ballast: 20V-30V), 50/60Hz, 1.0A. 3000V surge protection.
- Cordage: Two pre-crimped and pre-soldered wire leads; 3-ft 24V power input cable and 2-ft magnetic switch signal wire. 4-ft lamp cord.
- Ozone: UL 2998 validated no ozone. Meets California ozone emissions limit: CARB certified.
- Lamp: High-humidity, water-resistant, 15-lamp length.
- Lamp Life: 18,000 hours.
- Construction: Injection-molded thermoplastic co-polymer high-strength power module.
- Replacement Parts: UV2400XLAM2 The initial bulb is a two-year bulb but should be replaced every year after that.
Product Usage Instructions
- Installation
- Before Installing this Product:
- Read the instructions carefully to avoid damaging the product and causing hazardous situations.
- The installer must be a trained, experienced service technician.
- Included Inside Box:
- Unit Overview
- Germicidal UV-C Lamp
- Power Module
- 24V Power Input Cable
- Magnetic Switch Signal Wire
- UV Directional Lamp shield – Use in coil applications to direct UV away from furnace access panels.
- Mounting
- Direct Mounting Dimensions: 15.1 (384 mm) x 2.0 (50 mm) x 4.2 (106 mm)
- Magnetic Mounting Dimensions: 19.1 (485 mm)
- Included Mounting Hardware:
- Ensure proper clearances as indicated in Fig.2.
- Wiring And Transformer Installation Notes
- Verify available volt amperes before connecting the UV fixture to the 24 VAC circuit.
- Determine if the existing transformer can accommodate a 1.4 amp load.
- Beware that inadequate transformers may overheat due to an overdrawing system.
- Energize all components at full amp draw after installation to ensure proper operation.
- UV Installation Location
- The power module must be mounted directly to a metal surface for heat dissipation. Failure to do so may void the warranty and lead to premature lamp failure.
FAQs
- Q: How often should the UV lamp be replaced?
- A: The initial bulb has a two-year lifespan but should be replaced annually thereafter for optimal performance.
- Q: What precautions should be taken during installation regarding UV light exposure?
- A: Avoid looking directly at illuminated lamps as UV light can cause serious eye and skin damage, including temporary or permanent loss of vision.
Installation Instructions
Before Installing this Product
- Read these instructions carefully; failure to follow them could damage the product and cause a hazardous situation.
- The installer must be a trained, experienced service technician.
WARNING: UV Light Hazard.
- Harmful to bare skin and eyes. Can cause temporary or permanent loss of vision. Never look at lamps while illuminated.
- To prevent exposure to ultraviolet light, disconnect power to the ultraviolet air treatment system before servicing any part of the heating/air conditioning system.
- View illumination only through lamp handle or sight glass.
- Do not attempt to bypass the duct mount switch.
- Do not attempt to open the housing; the unit is sealed to prevent ultraviolet light exposure.
- CAUTION: Personal Injury Hazard. The HVAC power supply can cause electrical shock.
- Disconnect the HVAC power supply before installing, cleaning, or replacing ultraviolet lamp(s).
- CAUTION: Breakable Glass Hazard. Can cause personal injury.
- Be careful when inserting lamp(s) into the lamp base.
- Wear protective gloves when handling lamp(s).
- CAUTION: Personal Injury Hazard. The power supply can cause electrical shock.
- Disconnect the power supply before cleaning or replacing the ultraviolet lamp(s).
- Do not open the base unit or lamp handle; there are no user-serviceable components inside.
- CAUTION: UV Lamp Burn Hazard. Harmful to bare skin. Can cause severe burns.
- Disconnect power 15 minutes before removing the ultraviolet lamp(s).
Included Inside Box
- Power module
- Germicidal UV lamp
- Remote lamp extension cord
- Magnetic mounting bracket
- Directional UV lamp shield
- Magnetic switch
- UV safety viewport
- UV radiation hazard labels
- UV duct label
- Installation and operation manual
- Installation hardware
Unit Overview
Included Mounting Hardware
- (2) 8/32” brass knurled nuts
- (2) 6-20 x 7/16” Philip pan screws
- (3) 8-18 x 3/4” Philip pan screws
- (3) 8-18 x 2-1/2” Philip pan screws
- (1) Lamp knockout gasket
- (2) 1/8” ID rubber washers
- Magnetic switch
- UV warning labels
Specifications
- Model UV2400U2000 AirBRIGHT 2
- Size and Weight Power Module: 4.75” L x 3.16” W x 1.75” H
- Mounting Bracket (Magnetic): 3.5” L x 2.25” W x 3.5” H
- Weight: 2 lbs.
- Electrical Power: 24VAC (Expanded range ballast: 20V-30V), 50/60Hz, 1.0A. 3000V surge protection.
- Cordage: Two pre-crimped and pre-soldered wire leads; 3-ft 24V power input cable and 2-ft magnetic switch signal wire. 4-ft lamp cord.
- Ozone UL 2998 validated no ozone.
- Meets California ozone emissions limit: CARB certified.
- Lamp High-humidity, water-resistant, 15” lamp length.
- Lamp Life 18,000 hours.
- Construction Injection-molded thermoplastic co-polymer high-strength power module.
- Replacement Parts UV2400XLAM2 The initial bulb is a two-year bulb but should be replaced every year after that.
UV Installation Notes
- We recommend the AirBRIGHT 2 UV Air Purifier be installed on the supply side duct 3-5 inches above the A-coil, but it can also be installed on the return side if necessary.
- The germicidal UV light should be positioned to shine on the surfaces that are prone to mold growth like the A-coil, or be placed in an open area of the return duct where there are long straight runs.
- Install the magnetic switch and add the included stickers bearing the ULTRAVIOLET RADIATION hazard symbol on any doors/access panels which would allow direct UV light to shine through if opened while UV is powered.
- Make sure any doors/panels without magnetic switches remain closed while the UV is powered.
- To comply with UL Standards, a magnetic switch must be deployed across all access panels and doors that can expose an operator to more than of 1.7 μW/cm2 UV intensity.
- Do not operate UV-C LAMPS outside of the appliance.
Wiring And Transformer Installation Notes
This device requires a constant 24 VAC power source. It is recommended that
the device be powered by a dedicated, non-cycling, 40VA transformer. Cycling
this UV light will void the lamp’s warranty and lessen the effective lifetime
of the lamp. If powering from an existing transformer is already integrated
into a furnace, air handler, or other appliance, an upgrade may be required to
the original equipment transformer. Ensure there is adequate volt-ampere (VA)
capacity on the existing transformer to support an additional 1.4A draw from
this product.
- Verify the available volt amperes before connecting the UV fixture to the 24 VAC circuit. Energize all 24 VAC components so they reach their maximum amp load.
- After obtaining the available volt-amperes, determine if the existing transformer can accommodate a 1.4 amp load.
- Beware that inadequate transformers may initially seem to power up the circuit only to then overheat as a result of an overdrawing system.
- After installing the UV fixture, energize all 24 VAC components at their full amp draw, including the UV fixture, and ensure that all systems are operational and that fuses remain intact.
UV Installation Location
- The power module must be mounted directly to a metal surface.
- This will help the ballast dissipate heat. Failing to mount the ballast properly will void the warranty and may lead to premature UV lamp failure.
- This device may be installed in an air handler unit, a cased evaporator coil, or in an air plenum/duct.
- If the UV device is installed on the inlet side (return air side) of a coil, make sure that the UV rays are directed away from any filter media, plastic duct lining, plastic components, or accessible doors and panels.
- When properly installed, the UV lamp shield included in your package may help divert stray UV away from undesired directions.
- If the UVC lamp is placed inside of a cased system, the included magnetic switch is required to be attached to the access panel(s) of the system.
- If the UV device is installed near an air filter, check with the filter manufacturer for UV-C resistance properties. Optional
- UV directional lamp shield is included. If the desired UV installation location is intended to irradiate an air filter, to neutralize the microbiological matter on the air filter surface, such as would be found in the return air drop of a basement application or the return plenum of a horizontal system in an attic; take precautions as described in the note above, and make sure the UV fixture is placed on the return side of the filter.
- DO NOT INSTALL THE UV FIXTURE ON EITHER SIDE OF THE FILTER IN HALL / CLOSET RETURN AIR APPLICATIONS.
WARNING: UV Light Hazard.
- Can cause serious eye and skin damage.
- Harmful to bare skin and eyes. Can cause temporary or permanent loss of vision. Never look at lamps while illuminated.
Remote Lamp Installation (A-Coil Delta Plate)
- Note: Open the access panel to the A-coil. Drill a 7/8” knockout into the delta plate and place a gasket (included) around the knockout.
- (Optional) Attach UV lamp shield to direct UV away from furnace access panels. See page 2.
- Insert the lamp directly into the knockout and secure the lamp to the delta plate with two self-drilling screws. (Screws and rubber washers included.)
- Connect the remote lamp extension cord. Note: A-Coil delta plate installation does not use a lamp bracket.
Power Module Installation (Remote Lamp)
- With the lamp cordage facing away from the mounting surface, install the power module in a suitable location on the side of the system or within the control panel of the air handler using the two long self-drilling screws (included). Do not over-tighten.
- Drill a 7/8” knockout in the outer sheet metal where the remote lamp extension cord will be inserted.
- Connect the power module to constant 24 VAC power.
- Connect the magnetic switch. See page 6.
- Connect the lamp to the power module. Connectors are keyed for proper alignment.
WARNING
- UV Light Hazard.
- Can cause serious eye and skin damage. Do not look at UV-C light. Harmful to bare skin and eyes. Can cause temporary or permanent loss of vision. Never look at lamps while illuminated.
NOTICE
- Clean the lamp before installation.
- Use a cotton cloth to remove dirt and fingerprints. Failure to do so could shorten the lamp’s lifespan.
NOTICE
- Fully Seat Lamp Connector.
- Failure to properly seat the lamp connector could result in improper lamp operation and/or compromise water resistance.
NOTICE
- Lamp cleaning is not required after installation.
- Reference specifications page for lamp replacement part number and schedule.
Direct Lamp Installation (A-Coil Delta Plate)
- Drill a 7/8” knockout in the outer sheet metal where the lamp will be centered on the return side of the coil. See diagram.
- Place gasket (included) around knockout.
- Insert the lamp into the power module and secure it with self-drilling screws. (Included.)
- (Optional) Attach UV lamp shield to direct UV away from furnace access panels and critical plastic components. See page 2.
- Insert lamp directly into knockout and secure power module to duct with self-drilling screws (Included.)
- Note: A-Coil delta plate installation does not use a lamp bracket.
Power Module Installation (Direct Lamp)
- Drill a 7/8” knockout in the outer sheet metal where the power cord and magnetic switch signal wire will be inserted.
- Connect the power module to constant 24 VAC power.
- Connect the magnetic switch. See Figure 11.
- Connect the lamp connector to the power module connector. Connectors are keyed for proper alignment.
WARNING
- Electric Shock Hazard.
- Can cause injury or death.
- Disconnect all electrical power supplies before servicing.
WARNING
- For Use With 24 VAC Only.
- Do not exceed the voltage rating.
- Severe damage to the device and/or fire could result. Verify proper voltage.
Remote Lamp Installation (W-Coil / A-Coil Bracket Mount)
- Disconnect power to the air handler and open access panels.
- Slit insulation on the back or side wall of the air handler and attach a magnetic bracket to the wall. Bracket may optionally be secured using screws.
- (Optional) In coil applications, use a lamp shield to direct UV away from furnace access panels.
- Secure the lamp to the lamp bracket with the provided knurled nuts.
- Install power module per steps defined on.
Magnetic Switch Installation
- To comply with UL Standards, a magnetic switch must be deployed across all access panels and doors that can expose an operator to more than of 1.7 μW/cm2 UV intensity.
- When possible, it is recommended to mount the magnetic switch across two door panels.
- Switch wires are not polarity-sensitive.
- Max mounting gap: 5/8”.
- Remove interlock protective covers for access to screw mounting holes. Replace protective covers after mounting.
- If installing the device in ducting with no operator access, the magnetic switch can be bypassed by wire-nutting the two signal wires together.
UV-C Hazard Label Placement
- To comply with UL Standards, a UV-C Radiation Hazard label must be placed on any doors or access panels that can expose an operator to more than 1.7 μW/cm2 of UV intensity.
- Place UV-C Radiation Hazard labels at recommended locations.
WARNING
- UV Light Hazard.
- Can cause serious eye and skin damage.
- Do not look at UV-C light. Wear UV-C eye and skin protection.
Install UV Safety Viewport
- Adhere to the provided UV duct label to the outside of the duct near the installation location and drill a 5/8” knockout as indicated on the label. Press the UV safety viewport into a knockout.
- Close all access panels and reconnect power to the air handler.
- Verify that a blue glow can be seen through the UV safety viewport.
Lamp Maintenance
- Each time the lamp is replaced, note the date of lamp installation and the next recommended date of replacement on the duct label.
- The lamp does not require any routine maintenance, such as cleaning.
- Reference specifications page for lamp replacement schedule and replacement part numbers.
Mercury Notice
- This device contains mercury in the sealed ultraviolet lamp(s). Do not place your used lamp(s) in the trash. Dispose of it properly.
Broken Lamp Cleanup and Disposal
- Do not use a household vacuum. Sweep debris (phosphor/glass) into a plastic bag and dispose of it properly. Contact your local waste management authority for instructions regarding recycling and the proper disposal of old lamp(s).
Replacement Parts
- UV2400U2000 – AirBRIGHT® 2 Ultraviolet Air Purifier
- UV2400XLAM2 – Replacement Lamp for UV2400U2000
Warranty
Limited Warranty
Resideo warrants this product to be free from defects in workmanship or materials, under normal use and service. The warranty period on the power module is five (5) years from the date of first purchase by the original purchaser. The warranty on the bulb is two (2) years from the date of first purchase by the original purchaser. The warranty is not intended to cover parts replaced as part of the normal maintenance schedule. If at any time during the warranty period, the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option). If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or (ii) call Resideo Customer Care at 1-800-468-1502. Customer Care will determine whether the product should be returned to the following address: Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by damage that occurred while the product was in the possession of a consumer. Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422, or call 1-800-468-1502.
CONTACT
- Resideo Inc., 1985 Douglas Drive North
- Golden Valley, MN 55422
- www.resideo.com
- 33-00667EFS-01 SA
- Rev. 05-24
© 2024 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>