Whirlpool WHAD201DW 23 Pint Dehumidifier User Guide

Whirlpool WHAD201DW 23 Pint Dehumidifier User Guide

Models:
WHAD201DW WHAD301DW WHAD501DW

For questions about features, operation/performance, parts, or service, call: 1-800-207-1158. In Canada, for assistance, installation, or service, call: 1-800-207-1156.

TM 02023 Whirlpool. All rights reserved. Manufactured under license by XLS Products, Pennsylvania. Limited warranty provided by XLS Products.

DEHUMIDIFIER SAFETY

Your safety and the safety of others is very important.
We have provided many Important safely messages In this manual and on your appllanoe. Always read and obey all safety messages.

IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the r1sk of fire, elec1rlc shock, or Injury when using your air conditioner, follow these basic precautions:

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adap1er.
• This appliance Is not Intended for use by people (including children) whose physical, sensory or mental capacities are different or Impaired or who lack the necessary experience or knowledge/expertise to do so, unless such persons 1118 supervised or 1118 trained to operate the appliance by a person who accepts responsibility for their safety.
• Do not use an extension cord.
• Unplug air conditioner before servicing.
• Use two or more people to move and install air conditioner.
• Do not drink water collected in the water bucket.
• Children should be supervised to ensure that they do not play wi1h the appliance.

SAVE THESE INSTRUCTIONS

INTRODUCTION TO REFRIGERANTS R32

The refr1geranls used In our dehumidifier are envlronmen1ally safe hydrocarbons. This kind of refrigerant Is odorless and combustible, meaning It can bum and explode under certain circumstances. However, there Is no danger of burning or exploding n you comply with the below table when instelling your dehumidifier in a room with an appropriate area and use it correctly.

Compared to ordinary refrigerants, Refrigerant R32 is environmentally friendly, does not destroy the ozone, and has a very  little value of greenhouse effect.

WARNING

• Please read the manual before installation, operation, and maintenance.
• Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
• Do not pierce or bum the appliance.
• The appliance must be stored In a room without continuously operating Ignition sources (for example: open llamas, an operating gas appliance) and ignition sources (for example: an operating electric heater) close to the appliance.
• Please contact the nearest after-sale service center when maintenance Is necessary. At. the time of maintenance, the maintenance personnel must strictly comply with the Operation Manual provided by the corresponding manufacturer and any non-professional is prohibited to maintain the air conditioner.
• It is necessary to clear away the refrigerant in the system before maintaining or scrapping an air conditioner. Be aware the refrigerant may not contain an odor and is flammable.
• Keep ventilation openings clear of any obstruction.
• Any person who Is Involved with working on or breaking Into a refrigerant circuit should hold a current valid certificate from an industry-accredited assessment authority, which monitors their competence to handle refrigerants safely in accordance with an industry recognized ass11t1Bment specification.

INSTALLATION REQUIREMENTS

Electrical Requirements-All Models

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,  fire, or electrical shock.

The electrical ratings for your dehumidifier are listed on the model and serial number label. The model and serial number label is  located on the right-hand side of the dehumidifier cabinet.

Electrical Requirements

• 115 V (103.5 min.-126.5 max.)
• 0-12 A
• 15 A time-delay fuse or circuit-breaker
• If there is a “Single Circuit Only” label on the unit, use on a  dedicated single-outlet circuit only. If a dedicated single-outlet  circuit is not available, then it is the customer’s responsibility  to have a single-outlet circuit installed by a qualified  electrician.
• If there is no “Single Circuit Only” label on the unit, the unit  may be used on any branch circuit of correct voltage and  adequate current protection rating.

Recommended Grounding Method
This dehumidifier must be grounded. This dehumidifier is equipped with a power supply cord having a grounded 3-prong plug. To minimize possible shock hazard, the cord must be plugged into a mating, grounded 3-prong outlet, grounded in accordance with all local codes and ordinances. If a mating outlet is not available, it is the customer’s responsibility to have a properly grounded 3-prong outlet installed by a qualified  electrical installer. It is the customer’s responsibility:

• To contact a qualified electrical installer.
• To assure that the electrical installation is adequate and in  conformance with National Electrical Code, ANSI/NFPA
  70 – latest edition, and all local codes and ordinances.

Copies of the standards listed may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269

Installation Instructions

WARNING

Excessive Weight Hazard

Use two or more people to move and install  dehumidifier.
Failure to do so can result in back or other injury.

Remove Packaging Materials:

• Handle the dehumidifier gently while unpacking the unit.
• Remove the carton top and lift the dehumidifier from the base pad.
• Remove tape and glue residue from surfaces before turning on the dehumidifier. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with a damp cloth and dry.
• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your dehumidifier.
• Dispose of/recycle packaging materials in an appropriate way.

Caster Installation

Before use, remove the accessory from the bucket.

• Remove the bucket, rotate the handle to the position like fig  below, and remove the handle.
• Open the cover, take out of the the plug, and other accessories.
• Re-install the cover and handle, correctly put back the bucket into the unit.

Tilt the dehumidifier at no more than a 45-degree angle. With force, insert the four casters into the caster locations at the bottom of the dehumidifier. Make sure the ring around the caster is flush against the bottom of the dehumidifier.

PARTS AND FEATURES

Placement

This dehumidifier must be placed on a stable, level, and solid floor that will support its weight with a full bucket of water. Allow at least 12-18″ (30-45 cm) of clearance from walls and furniture.
Do not allow the air inlet or outlet to be covered by drapes or curtains, as this will reduce performance.

Use the dehumidifier in an area where the temperature will not fall below 410F (SC). At temperatures below 410F (50C), the coils can become covered with frost, resulting in reduced performance.

Use the dehumidifier in cooking, laundry, bathing, and dish washing areas that have excessive moisture.

Use the dehumidifier to prevent moisture damage anywhere books or valuables are stored.

Use the dehumidifier in a basement to help prevent moisture.
The dehumidifier must be operated in an enclosed area to be  most effective.
Close all doors, windows, and other outside openings in the room.

Electrical Connection
  WARNING

Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

USING YOUR DEHUMIDIFIER

WARNING

Sickness Hazard

Do not drink water collected in water bucket.
Doing so can result in sickness.

When the water collection bucket is full, the Bucket Full indicator will light and the dehumidifier will turn off. The dehumidifier will not function until the water bucket is emptied and replaced.

When the bucket is removed from the machine, the compressor will turn off, but the fan will continue to run for a few minutes.
This is normal. The dehumidifier will not be removing moisture from the air at this time.

Continuous Mode and Drain Hose Connection (optional)

The Continuous mode allows the unit to run continuously (depending on the selected humidity level) without having to empty the water bucket.

To drain continuously, attach a hose (not included) for water drainage into a floor drain.

The drain fitting uses a standard garden hose connector.
The drain hose must be below the drain port on the back of the dehumidifier to ensure proper drainage.
NOTE: Use GHT or “garden hose thread”, which has an outer diameter of 11/16″ (27 mm) and a pitch of 11.5 T PI (threads per inch).

Thread the drain hose (not included) onto the drain fitting on the dehumidifier. Lead the rest of the hose to a floor drain and cut to length (no longer than 6′ long). Make sure that there are no kinks or knots in the garden hose. Turn on the unit and press the Mode button until set to Continuous mode.

CARE AND CLEANING

Your new dehumidifier is designed to give you many years of  dependable service. This section tells you how to clean and care  for your dehumidifier properly.

Cleaning the Filter

The filter is removable for easy cleaning. A clean filter helps remove dust, lint, and other particles from the air and is important for best operating efficiency. Check the filter every two weeks to see whether it needs cleaning.

NOTE: For best performance, do not operate the dehumidifier without the filter in place.
Rinse the filter under the faucet. If the filter is very dirty, wash it in warm water with a mild detergent.
NOTE: Do not wash the filter in the dishwasher or use any chemical cleaners; it may damage the filter. Air dry the filter completely before replacing to ensure maximum efficiency.

Remove the filter from back of the unit by using your thumbs to press down on the tabs directly above the filter.

Reinstalling the filter:

1. Wait until the filter is completely dry.
2. Reinstall the filter in the dehumidifier.
3. Press the Filter button to reset the filter indicator.

Cleaning the Dehumidifier Cabinet

1. Turn off the dehumidifier.
2. Wipe the dehumidifier cabinet with a soft, damp cloth.
3. Wipe dry with soft cloth.

Cleaning the Water Bucket
The water bucket should be cleaned every few weeks to prevent  mold and mildew growth.

1. Remove the water bucket.
2. Wash the bucket with a mixture of warm water and a mild detergent.
3. Rinse well, then reinstall water bucket.

WARNING
Excessive Weight Hazard
Use two or more people to move and install  dehumidifier.
Failure to do so can result in back or other injury.

Storing the Dehumidifier
If the dehumidifier will not be used for an extended period of  time, prepare it for storage with the following steps.

1. Turn off the dehumidifier and unplug it.
2. Empty the bucket.
3. Remove, clean, and reinstall the filter.

TROUBLESHOOTING

Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.

WARNING
Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

ASSISTANCE OR SERVICE

Before ceiling for assistance or service, please check Troubleshooting. It may save you the coat of e service cell. If you still need help, follow the instructions below.

When calling, please know the purchase date and the complete model end serial number of your appliance. This Information will help us to better respond to your request.

In the USA

Call XLS Products Customer Service toll free at 1-800-207-1 156.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.
• Installation information.
• Use and maintenance procedures.
• Accessory and repair parts.
• Specialized customer assistance.
• Referrals to local dealers, repair parts distributors and service companies. XLS Products designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in the United States.

For further assistance:

If you need further assistance, you can write to XLS Products with any questions or concerns at

XLS Products, Inc.
Customer Service
P.O. Box 16262
Philadelphia, PA 19114-0262
Please include a daytime phone number in your correspondence.

In Canada

Call the XLS Products Customer Service toll free at 1-800-207-1156.
Our consultants provide assistance with:

• Features and specifications on our full line of appliances.
• Use and maintenance procedures.
• Accessory and repair parts.
• Referrals to local dealers, repair parts distributors, and service companies. XLS Products designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in Canada.

For further assistance:
If you need further assistance, you can write to XLS Products with any questions or concerns at
XLS Products, Inc.
Customer Service
P.O. Box 16262
Philadelphia, PA 19114-0262
Please include a daytime phone number in your correspondence.

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this product is operated and maintained according to instructions attached to or furnished with the product, XLS Products will pay for replacement parts and repair labor to correct defects in materials or workmanship or replace the product at our discretion. Service must be provided by a XLS Products designated service company.
This warranty does not cover the air filter.

ITEMS XLS PRODUCTS WILL NOT PAY FOR

1. Service calls to correct the installation of your product, instruct you how to use your product, to replace house fuses or reset circuit breakers, replace or clean filters, or correct house wiring.
2. Service calls to repair or replace air filters. Those consumable parts are excluded from warranty coverage.
3. Repairs when your product is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by XLS Products.
5. Replacement parts or repair labor costs for units operated outside the United States or Canada
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service in remote locations.
9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. XLS PRODUCTS SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE OR PROVINCE TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized XLS Products dealer to determine if another warranty applies.

If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling XLS Products. In the U.S.A., call 1-800-207-1156.
In Canada, call 1-800-207-1156.

Keep this book and your sales slip together for future reference.
You must provide proof of purchase or installation date for in-warranty service.

Write down the following information about your dehumidifier to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial number. You can find this information on the model and serial number label located on the product.

Dealer name
Address
Phone number
Model number
Serial number
Purchase date

@/TM 02023 Whirlpool. All rights reserved. Manufactured under license by XLS Products, Pennsylvania.
Limited warranty provided by XLS Products.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>