LENOXX WMH20 Wall Mounted Heater and Fan with Remote Control Instruction Manual

LENOXX WMH20 Wall Mounted Heater and Fan with Remote Control

Specifications

Product Usage Instructions

Safety Instructions

1. Ensure proper wall mounting with air outlet facing downward.
2. Avoid using in areas with combustible materials or explosive gases.
3. Replace damaged cords by qualified persons to avoid hazards.
4. Avoid placing near socket outlets and maintain proper electrical requirements.
5. Disconnect the plug when unattended or during maintenance.
6. Avoid touching with wet hands or conductive material.
7. Stop operation if the motor malfunctions.
8. Avoid continuous opening of doors or windows for optimal heating efficiency.
9. Switch off the heater using the on/off button.

Installation

1. Drill holes in the wall, maintain distance from the ground and secure the heater using provided screws.
2. Ensure the wall can withstand weight before installation.
3. Maintain distance between product and ceiling/walls.
4. Align the screw with hole A, and slide to position B for secure fastening.

Getting Started

1. Ensure power supply meets requirements and connect the heater to the outlet.
2. Switch on the appliance using the provided controls.
3. Operate with included remote control for various settings.

FAQ

• Q: Can this heater be used in small rooms?
  A: This heater should not be used in small rooms occupied by individuals who cannot leave on their own unless constant supervision is provided.

• Q: What should I do if the motor malfunctions?
  A: Immediately cease operation and contact the manufacturer or a qualified person for assistance.

• Q: How do I ensure optimal heating efficiency?
  A: Avoid continuous opening of doors or windows while using the heater to maintain optimal heating efficiency.

SAFETY INSTRUCTIONS

Read and understand this entire manual before using this product. Keep these instructions for future reference.

1. Ensure the heater is securely mounted on the wall with the air outlet facing downward. Avoid placing it in unstable or tilted positions.
2. Do not use the heater in areas with combustible materials or explosive gases. Keep the air outlet unobstructed.
3. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
4. Avoid placing the heater directly below or in front of a socket outlet. The electrical outlet must have a 220-240V, 50-60Hz power supply, and ensure proper contact between the socket and plug.
5. When the heater is unattended or during maintenance, disconnect the plug.
6. Do not touch the heater with wet hands or any conductive material.
7. Immediately cease operation if the motor malfunctions.
8. While using the heater, avoid continuous opening of doors or windows to maintain optimal heating efficiency.
9. To turn off the heater, switch the on/off button to the off position. The fan will run for 30 seconds, blowing cool air before stopping. Unplug the device afterward.
10. Do not use the heater in bathrooms.
11. Use the timer to set the heater’s operating hours.
12. Remove the battery from the appliance before disposal. Dispose of the battery safely.
13. The heater must be installed at least 1.8 meters above the floor.
14. For repairs, contact our service department.
15. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
16. Children should be supervised to ensure that they do not play with the appliance.
17. CAUTION: Certain parts of the product can become very hot and cause burns, especially where children and vulnerable individuals are present. Exercise caution accordingly.

REMOTE CONTROL BATTERY WARNING

This product contains a coin/button cell battery inside. If swallowed, go straight to a hospital emergency room.

• WARNING – KEEP BATTERIES OUT OF REACH OF CHILDREN
• Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns and potential perforation of the esophagus.
• If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Information Centre on 13 11 26 (in Australia) or the 24-hour National Poisons Centre on 0800 764 766 (in New Zealand) for fast, expert advice.
• Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use it if the compartment is not secure.
• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.

WARNING:
This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.

PRODUCT OVERVIEW

• Model WMH20
• Rated Power 2000W
• Rated Voltage 220-240V~
• Frequency 50/60Hz

INSTALLATION

Drill two holes in the wall, maintaining a distance of at least 2.0m from the ground. The hole diameter should be 6mm. Once the anchor plugs and screws are in place, attach the heater. Secure to the wall as illustrated below.

Note:
Verify that the wall can withstand 4.1kg weight before proceeding with the installation.

The distance between the product and the ceiling/walls should be ≥30cm.

Note:
When installing the product, align the screw with hole “A” on the product. Once hung, slide to position “B” to securely fasten it. When removing the product, shift from position “B” back to “A” before taking it off.

GETTING STARTED

Make sure the electrical outlet has a 220-240V, 50-60Hz power supply. Connect the heater to the power outlet and ensure proper contact between the socket and plug.

• Switch the appliance on.
• “0” is “OFF”. “|”: is “ON”.

Operate the heater using the included remote control.

Simple control
The unit can be turned on (high-heat setting only) using the button on the side of the heater, below the power switch. Press once to start, and press again to stop. After shutdown, the fan will continue operating for 30 seconds to cool down the appliance.

Remote Control

Display

CLEANING & CARE

• Wait for the heater to cool down and ensure the plug is disconnected before cleaning.
• Use a soft, damp cloth with mild detergent; do not use abrasive detergents, and do not immerse in water or any other liquid.
• Do not pour water into the machine.

Contact Information

• www.lenoxx.com.au
• 1300 666 848
• Instagram: LenoxxElectronics
• Facebook: LenoxxElectronics

References

• Best Consumer Electronics and Home Appliances | Lenoxx Australia – Lenoxx Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>