2GIG GB1e Glass Break Detector Installation Guide
- June 29, 2024
- 2GIG
Table of Contents
- INSTALLATION INSTRUCTIONS
- Contents
- Inserting and Replacing the Batteries
- Wall Mounting
- Glass Type and Thickness
- PROGRAMMING
- RF TESTING
- Industry Canada (IC) Compliance
- Regulatory Information
- FCC Notice
- Limited Warranty
- Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
2GIG GB1e Glass Break Detector
INSTALLATION INSTRUCTIONS
The E+ Glass Break Detector ( 2GIG-GB1E-900) is a fully-supervised, tamper- protected, ceiling- or wall-mounted unit. It is one of the E+ devices from Nice North America LLC providing extended wireless range with encrypted communications to the control panel using the 900Mhz frequency. The detector provides a 2 ft (7.6 m) maximum detection range, 360° maximum horizontal sensing angle, and dualstage glass break detection.
Contents
Verify that the package includes the following:
- 1—Glass Break Detector (with Mounting Base)
- 2—Lithium Batteries
- 3—Plastic Wall Anchors with Screws
A RED LED
B GREEN LED
C TEST button
D Imprinted arrow (for alignment of cover and base)
Inserting and Replacing the Batteries
To insert or replace the batteries:
-
Unwrap the door contact.
-
Holding the cover and base, twist the cover in a counter-clockwise motion. When the imprinted arrows on the side of the detector are aligned, separate the unit.
-
Remove the old batteries.
IMPORTANT: Always dispose and/or recycle used batteries in accordance with the hazardous waste recovery and recycling regulations for your location. Your city, state, or country may also require you to comply with additional handling, recycling, and disposal requirements. -
Insert the batteries in the compartment. Always match the plus (+) sign on the battery with the flat side of the compartment and the minus (–) sign on the battery with the spring side of the compartment. It takes approximately five (5) seconds for the detector to power ON.
A Tamper switch
B Battery compartments (RED tabs located behind compartments)
WARNING : Failure to follow these warnings and instructions can lead to heat generation, rupture, leakage, explosion, fire, or other injury, or damage. Do not insert the battery into the compartment in the wrong direction. Always replace the battery with the same or equivalent type (see Specifications on page 2). Never recharge or disassemble the battery. Never place the battery in fire or water. Always keep batteries away from small children. If batteries are swallowed, promptly see a doctor.
Wall Mounting
When wall mounted, the detector provides protection coverage on the opposite or adjacent window. Windows on the same wall as the detector are not protected.
To mount the detector to a wall:
-
If not already installed, insert the batteries (see “Inserting and Replacing the Batteries”).
-
Place the base of the detector on the adjacent or opposite wall from the window being protected.
-
Use the three (3) Plastic Wall Anchors (provided) to mount the base of the detector to the wall.
IMPORTANT: Always mount the detector so the Test button is in the downward position. -
Holding the cover, align the Tamper with the Tamper Slot, then use a clockwise twist motion to lock the cover to the mounted back plate.
Glass Type and Thickness
The minimum size and shape for all glass types is 11 x 11 in (28 x 28 cm) square. Glass must be framed in the wall of the room or mounted in a 36 in (91 cm) barrier.
Figure 3 Battery Compartment and Polarity
Type | Minimum to Maximum Thickness |
---|---|
Plate |
1/8 – 1/4 in (3.2 – 6.4 mm)
Tempered
Sealed Insulating†
Sealed insulating glass types are protected only if both plates of glass are broken.
PROGRAMMING
The following steps describe general guidelines for programming (Learning) the sensor into the alarm control panel memory. For more details, refer to the 2GIG Installation & Programming Instructions.
- Set the panel to Sensor Learning mode.
- Pull battery tab from the Detector to start auto-learn.
- If Detector is already powered up, press and hold the Test button for 3 seconds until red LED starts to flash (see Figure x).
- Once pairing is successful, the Detector LED will long flash red one time, turn off and then exit pairing mode.
NOTE: Pairing mode expires automatically after 1 minute of entering the mode.
RF TESTING
To verify good RF signal, use the following steps:
-
Press the Test button twice.
-
Observe LED flashing.
Good signal: One long flash
Poor signal: Two quick blinks -
The sensor exits Signal Test mode automatically afterward.
Industry Canada (IC) Compliance
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Regulatory Information
We, Nice North America, LLC of 5919 Sea Otter Place STE 100, Carlsbad, CA 92010, declare under our sole responsibility that the device, 2GIG-DW10E-345 complies with Part 15 of the FCC rules.
FCC Notice
This device complies with Part 15 of the FCC’s Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- The device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003 Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC:
Federal Communication Commission (FCC) Radiation Exposure Statement: When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.
IC:
Radiation Exposure Statement : This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This product complies with FCC radiation exposure limits for an uncontrolled
environment. Avoid operating this product at a distance less than 20 cm from
the user.
CAUTION: Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Limited Warranty
This Nice North America LLC product is warranted against defects in material
and workmanship for two (2) years. This warranty extends only to wholesale
customers who buy direct from Nice North America LLC or through Nice North
America LLC’s normal distribution channels. Nice North America LLC does not
warrant this product to consumers. Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any
There are no obligations or liabilities on the part of Nice North America LLC
for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties for functionality, are valid only until
the warranty expires. This Nice North America LLC Warranty is in lieu of all
other warranties expressed or implied.
Specifications
Wireless Signal Range | TBD, open air, with Wireless Control Panel |
---|---|
Code Outputs | Alarm; Alarm Restore; Tamper; Tamper Restore; Supervisory; |
Low Battery
Transmitter Frequency| 902MHz~928MHz
Supervisory Interval| 70 minutes
Sensor Type| Single microphone, dual stage thud, and crash
Maximum Horizontal Sensing Angle| 360° for ceiling mount or 180° for
wall mount
Dimensions (D x H)| TBD
Weight (including battery & magnet) | TBD
Housing Material| ABS Plastic
Color| White
Operating Temperature Limits| 32° to 120° F (0° to 49° C)
Relative Humidity| 5-90% Non-Condensing
Battery (installed with pull tab)| Two (2) CR 123A 3V or equivalent
Lithium batteries
Approved Glass Break Simulator| FG-701 Glass break Simulator
Certification| ETL, FCC and IC
Panel Programming Sensor Loop| Loop 1
Customer Service
800-421-1587 M – F, 8am – 7pm EST
Nice North America LLC
5919 Sea Otter Place, Suite 100 Carlsbad, CA 92010
Niceforyou.com
©2023 Nice North America LLC. 2GIG is a registered trademark of Nice North
America LLC. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>