POWERWAY T1-02 Bluetooth Headband Instruction Manual
- June 28, 2024
- POWERWAY
Table of Contents
POWERWAY T1-02 Bluetooth Headband Instruction Manual
Product Information
Specifications
- Class: B digital device
- Compliance: FCC Rules Part 15
- RF Exposure: General RF exposure requirement met
- Usage: Portable exposure condition without restriction
Product Usage Instructions
Warnings and Compliance
Changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.
Installation and Interference
Ensure the equipment is installed following the provided instructions to prevent harmful interference with radio communications in a residential setting.
Operation Conditions
Operate the device under the following conditions:
- The device should not cause harmful interference.
- The device must accept any received interference, even if it leads to undesired operation.
- The device can be used in portable exposure conditions without restrictions.
We added the concept of high-definition audio speaker design to the headband. In addition to daily use, it can also create a private space for you. You can play music, and watch videos and movies while using the headband without wearing additional headphones. This is also a good gift for meditation. Suitable for family, work, travel, leisure, exercise and sports;
Instructions for using
Assembly diagram
- A: Through the direction of Pu Leather Keys, determine the direction of the motherboard and the three assembly points around the ear.
- B: Pay attention to the inside and outside of the fabric, the speaker outlet and the motherboard plane (not the convex surface of the button) are inside the fabric close to the skin.
- C: The positions of the 3 assembly points correspond to the 3 dedicated wrapping positions of the fabric, and enter from the same direction of the headscarf.
- D: The order of entrance is suggested as follows: the left ear speaker first, then the Bluetooth motherboard, and finally the right ear.
- E: In order to ensure the wrapping of the main board and the speaker, please enter from the small opening of the unlocking button.
- F: To take out the 3 assembly parts, follow the above instructions and operate in reverse.
Host performance parameters
Host performance
Bandwidth 20-3000 hz, 3252 resistance value, Japanese Tony Copper Wire coil.
Fabric composition: 95% polyester, 5% SPANDEX.
Instructions
- Turn it on: Long press the Middle Button for 1.5 seconds, and the machine goes into pairing mode, at which point the red and blue lights flash alternately;
- Search for Bluetooth matching names: H01 by Swaytail;
- The key “+ “and the key”-“: Click the “+” key to increase the volume; Click and long press the “+” key for the next song; Click the”-” key to reduce the volume; Click and long Press the”-” key for the last song;
- Charge indication: Usually there’s a battery indicator on the phone, different systems, and different phone locations;
- Turn it off: Press the function key for 5 seconds.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, under Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FAQ
Q: Can I modify the equipment?
A: No, any changes or modifications not approved may void your authority to operate the equipment.
Q: What should I do if there is interference during operation?
A: Ensure that the device is installed and used according to the instructions provided. If interference persists, contact customer support for assistance
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>