CETPRO GS329 Freestanding Bathtub Installation Guide

CETPRO GS329 Freestanding Bathtub

Product Specifications

• Model: GS329
• Type: Freestanding Bathtub
• Manufacturer: ProHome

FAQ

Frequently Asked Questions

• Q: What should I do if I receive a missing part or a defective product?
  • A: In case of a missing part or a defective product, please contact ProHome customer service immediately at 626-679-3588 or email at service@getprohome.com for assistance with replacement or repairs.

TOOLS REQUIRED FOR INSTALLATION

TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)

CAUTION: TWO PERSON LIFT REQUIRED

• 2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT

Product Information

• Carefully, remove the tub from it’s crate/box.
• Important Note: Bathtub must be carried by a minimum of 2 adult people in upside down position only. Do not carry the bathtub by its panel.
• To avoid scratches or damages to the bathtub be sure to set it on cardboard with soft blanket on top of the cardboard.

• Set your bathtub on two 4×4 pieces of lumber so you can have access from the bottom of the bathtub. Put a tray beneath the bathtub.
• Very Important! Before proceeding with installation, please check that push scupper plug, drain, and integrated overflow are properly sealed and tightened.
• Push the scupper plug into a close position and fill the bath- tub with cold water above the overflow level to test for over- flow leakage and drain leakage.
• Check for any leaks around the drain and pipe. (NOTE: Due to surface tension, it is normal for a small amount of water to pool around the drain)
• If a leakage occurs please disassemble the drain line or overflow.

INSTALLATION WITH UNDERFLOOR ACCESS

• Step 1: Clean, level and prepare the floor for installation, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.
• Step 2: Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.
• Step 3: Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additonal 1/8″ or 3/16″ so thatthe weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls. Pop up cover drain body rubber drain gasket tail piece (provided by installer) floor drain pipe (provided by installer) trap (provided by installer) rubber drain gasket P-trap.
• Step 4: Install an 1-1/2″ tail piece along with the corresponing flanged washer and 1-1/2″ nut to thedrain body.
• Step 5: Measure and cut the tail piece to the appropriate length to reach the trap adapter When seting the tub drain, insert tail piece with 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.
• Step 6: Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and a bead of tub and tile caulk around the edge of the tub.
• Step 7: Flip the tub over and carefully set the tub into position with tail piece assembly to P-trap and connect to the drain.
• Step 8: Fill the tub with water to the overflow and then drain the tub whileinspecting the waste andoverflow connection below the floor for any leaks. Access from below will be necessary for this step.
• Step 9: With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.
• Step 10: DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone sealant to dry.

Note: If installing on a concrete slab where no underfloor access or cannot move drain.
You may consider following option.

• Optional flexible drain hose from plumbing hardware or home improvement store may be used GETPRO will not supply this flexible hose). Connect one end ataches to the bathtub drain and the other end needs to be atached to the floor drain by using a transition piece.
• Optional Island tub drain may also be used.
• Create a bridge from bathtub drain to floor drain by certified plumber only because any wrong connection or loosen on connection will cause leaks.

INSTALLATION ON SLAB FLOOR

INSTALLATION ON SLAB FLOOR (NO UNDERFLOOR ACCESS)

• Step 1: Clean, level and prepare the floor for installation, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.
• Step 2: Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.
• Step 3: Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additional 1/8?or 3/16?50 that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.
• Step 4: Measure the actual distance from drain into drain pipe on floor and the drain pipe should extend approximately 1″ above the finish floor. Use a drain adapter (not provided) if necessary.
• Step 5:  Clean the surrounding of the drain pipe with cloth in preparation of setting the drain, the area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole, also apply plumber putty to the washer and slide it over the bothom of the drain body.
• Step 6: Apply putty to fix the rubber silp gasket over the drain vent
• Step 7: Apply a generous bead of adhesive or waterproof silicone to the botiom of the tub and caulk around the edge of the tub.
• Step 8: Flip the tub over and carefully set the tub into position with tail piece assembly to waste vent and connect to the drain.
• Step 9:  With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.
• Step 10: DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone to dry.

IMPORTANT SAFETY RULES

ATTENTION:  ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB

Warnings

• The bathtub must be installed and used as described in this manual
• Use caution when entering or exiting the bathtub
• Do not permit children or persons with infirmities to use the bathtub without supervision of an adult
• People using any medications or having adverse medical history must consult a physician prior to use of the bathtub to avoid potential hyperthermia and possible drowning
• Water temperature over 100°F may cause hyperthermia and/or other health problems. Check water temperature and adjust it for your personal comfort
• Never use bathtub while intoxicated, ader taking meals or any alcoholic beverages. Consuming alcoholic beverages before or during bathing will cause drowsiness and may result in hyperthermia, loss of consciousness, or even drowning
• If you are pregnant or you feel that you are may be pregnant, consult your doctor before using the bathtub
• Never use any electrical devices such as hair dryer, lamp, telephone, tv, radio, or others within 5 feet of the bathtub
• Do not overfill the bathtub before entering. Entering the bathtub when filled will cause overflow and slippery

Care, Cleaning And Repair

Care and Cleaning

• Most dirt will wash off with mild soap and warm water.
• For tough spots, use liquid dish washing soap or non-chlorine bleach.
• Do not use abrasive material such steel wool or scouring pads to clean the acrylic surface.
• Always test the cleaning solution on a small area before using it on the entire surface.
• Do not allow cleaning to soak on the acrylic surface.
• Rinse thoroughly with water immediately and wipe dry with soft cloth.

Repair and Maintenance

• Use liquid polish compound such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of acrylic surface.
• Light scratches can be removed with polishing compound for automobiles.
• For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger than the scratch in a circular motion to remove the scratches. Repeat until the cratch is removed. Use soft cloth and small amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

IMPORTANT!

• DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and simmilar solutions. Use of such solutions may cause corrosion, finish peeling, and/or dull the surface.
• DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.

Contact

Retain these installation instructions for future reference!

If you have any questions or concerns, please do not hesitate to contact us

• www.getprohome.com
• 626-679-3588
• service@getprohome.com
• 162 Atlantic St, Pomona, CA 91768

INSTALLATION VIDEO

Missing Part or Defective?

Please Contact the Customer Service Team

• service@getprohome.com
• 626 679 3588

PRODUCT INSTRUCTION VIDEO

Documents / Resources

| CETPRO GS329 Freestanding Bathtub [pdf] Installation Guide
GS329 Freestanding Bathtub, GS329, Freestanding Bathtub, Bathtub
---|---
| CETPRO GS329 Freestanding Bathtub [pdf] Installation Guide
GS329 Freestanding Bathtub, GS329, Freestanding Bathtub, Bathtub

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>