OCG TA-5000 2.4GHz Wireless Gaming Headset User Manual

OCG TA-5000 2.4GHz Wireless Gaming Headset

INTRODUCTION

OCG TA5000 Wireless 2.4GHz Gaming headset,equipped with a 50mm high precision neodymium drivers and soft leatherette ear cups,which offers a particularly immersive sound quality,delivers you extreme gaming experience and greatly highlight your gaming atmosphere,born for every FPS!With the USB connection,it could be perfectly compatible with PC/laptop PS4, Mac and other devices with USB port.

WARNING
To prevent possible hearing damage, do not listen at high volume levels for long periods.

PRODUCT OVERVIEW

1. Adjustable Headband
2. Retractable Microphone
3. RGB LED Light
4. Volume Wheel
5. Mic On/Off Button
6. Power Button
7. LED On/Off Button
8. Charge Port
9. USB Charge Cable
10. USB Dongle
11. USB C AM to 3.5mm cable

HEADSET POWER/MIC BUTTON

Headset Power Button

• A. Power On/Off: Hold down the power button for 3 seconds until you hear a beep.
• B. Play/Pause: Click the power button once
  The RGB light will turn on when the headset is working.

Mic Mute Button

HEADSET CHARGING

1. It is recommended to fully charge the headset before first usse.
2. When the headset remaining the battery level is low, you will hear a beep on your headset.
3. Connect the Type-C cable to the charging port on the headset, and plug the other end into any USB power source.

HEADSET CONNECTION

To use the wireless headset on your device (PC, PS4, Nintendo, Mac):

1. Connect the wireless adapter to a USB port on your device (PC, PS4, Nintendo, Mac).
2. Press the power button on the headset for 3 seconds to power on.
3. When the headset ear cup LED is solid, the headset is connected.
   *Note: If it is your first time using the headset, you may need to set the headset as the default input and output device

Headset PlayStation 4 Configuration

1. Click the ‘settings in the screen.
2. Click on the ‘Devices’ tab, then go to the next step.
3. Click on the ‘Audio Devices’ tab, then go to the next step.
4. Click on ‘Input Device’ and ‘Output Device’ right-click on Wireless Dongle’ and select ‘Set as Default Device ,adjust the ‘volume control (headphones).

TROUBLESHOOTING TIPS

No sound/low sound

Possible Cause| Solution

Volume Control

|

Press the Volume Up button on the Ear Force Headset Audio Controller If necessary. Press the Game button of the Chat/Game Mix.

App Problem| Close the active App and re-ope n it alternatively
Loose Connector| Confirm that each plug is inserted

Voice interrupted

Possible cause

Setting

| Solution

Check the default (input and output) sound device is selected for this headset.

Weak Signal| Check the network.

Any further question, please feel free to contact us though Amazon or email us via. yiteng0307@163.com, and we are here to serve you all the time

TECHNICAL SPECIFICATION

• Drive Unit: O50MM
• Impedance: 32:15%ohm
• Sensitivity(S.PL): 105t3dBat1khzheadset
• Input Power: 10mw
• Frequency Response: 20-20KHz
• Microphone sensitivity: 42+3dB
• Transmission Distance: 10m
• Playing Time: 17H(Medium volume)
• Battery: Polymer Lithium Battery
• Battery Capacity: 3.7V/1200 mAH
• Charging Time: 1-2H

SAFETY AND PRECAUTION

Carefully read the information in this instruction manual and on the package before using this product

Safety

• Observe all warnings, precautions and instructions
• CHOKING HAZARD-Contains small parts. Keep out of the reach of small children.
• Stop using the system immediately if you begin to feel tired or if you experience discomfort or pain in your head while operating the wireless stereo headset. If the condition persists, consulta doctor.
• Avoid prolonged use of the wireless stereo headset. Take a break at about 15-minute intervals
• Permanent hearing loss may occur if the headset is used at high volume. Set the volume to a safe level.
• Overtime, increasingly loud audio may start to sound normal but can actually be damaged to your heanng.
• If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked.
• The louder the volume, the sooner your hearing could be affected. To protect your hearing:
  • Limit the amount of time you use the headset at high volume.
  • Avoid raising the volume to block out noisy surroundings
  • Lower the volume if you can’the ar people speaking near you.
  • If you feel that the headset is irritating your skin, stop using it immediately.
  • Do not disassemble or insert anything into the headset because this may cause damage to the internal components or cause injury to you.
  • Observe all signs and instructions that require an electrical device or radio product to be switched off in designated areas, such as gas/refuelling stations, hospitals, blasting areas, potentially explosive atmospheres or aircraft.
  • The battery used in this device may present a risk of fire or chemical burn if mistreated.
  • Do not disassemble, heat above 60’C, or incinerate.

FCC warning

• This device complies with part 15 of the FCC Rules.
• Operation is subject to the following two conditions:
  1. this device may not cause harmful  interference,
  2. this device must accept any interference received, including interference that may cause undesired operation.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
• If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• The device has been evaluated to meet general RF exposure requirement.
• The device can be used in portable exposure condition without restriction.

Room 301,Building 5, Number 581 Bao Shi Road.
Qr’Shi Twon Dong Guan City GuangDong China.
Email:yiteng0307@163
Tel:+8613717182931

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>