Enping SOM-24 Professional Wireless Microphone User Manual

Enping SOM-24 Professional Wireless Microphone

Specifications:

• Wide frequency response
• High signal/noise ratio
• High noise resistance
• Super quiet function with low T.H.D.
• No beating when turned on to protect amplifier boxes
• Status and power level indicators
• Usage up to 100m in surrounding environment, 30-50m for pair
• Independent and balanced exit
• Double-way channels for two simultaneous devices
• Suitable for medium or large stages, karaoke rooms, or home

Product Usage Instructions

Setup:

1. Place the receiver near the audio adjustment.
2. Connect the force and directional cable on the mixed A+B+Cou outputs.
3. Connect the Aou output on the B output separately with two signal cables.
4. Connect the amplifier or microphone adjuster by connecting the two antennas.

Power On:
Turn on the device using the Receiver ON button. The power indicator will light up, and the receiver will enter Standby mode.

Battery Installation:
Remove the cover from the battery compartment, insert the batteries, and close the lid securely.

FAQ:

• Q: What should I do if the microphone indicator stays on for a long time?
  A: If the microphone indicator remains on for an extended period, try using different types of transmission equipment. If the issue persists, contact customer support for assistance.

• Q: What should I do for security checking and adjustments?
  A: Ensure that safety requirements are met after any maintenance. If the product is damaged or not functioning correctly, seek technical assistance from the manufacturer.

System Modules:

• Operating frequency: 534-598 Mhz
• Frequency deviation: 55dB
• Audio Output: 0-300mV
• Reception channels: 2
• Voltage: 220(110) VAC +-10%
• Power: 200mA
• Antenna: Omni-directional antenna

Transmitter:

• Operating frequency: 534-598 Mhz
• Frequency deviation: [missing data]

Introduce

• Thank you for purchasing this product, please read this manual carefully to understand how to properly operate this product.
• Store this manual in a safe place for future consultation;
• This professional wireless microphone system uses the efficient American technique of low consumption discharge with a super sensitive UHF band receiver controlled by a 15 ppm crystal and combined with in dependent frequency mobile compressor, expanded circuit, frequency limiting circuit, silent circuit, and noise reduction.
• The reverb resistance circuit and output control is designed by EDA computer system
• Each system is electrically stated by our quality control.

Characteristics:

• Wide frequency response, high signal/noise ratio – High noise resistance.
• Super quiet function, low T.H.D.
• No beating when turned on thus protecting the amplifier boxes.
• Status and power level indicators.
• Usage at up to 100m in the surrounding environment and 30-50m for the pair.
• Independent and balanced exit.
• Designed with double-way channels, base for two simultaneous devices to sing without causing any disturbance.Can be used in medium or large stages, karaoke rooms or at home, etc.

Front and Rear Panel-Functions

1. Receiver ON button
2. Volume CH B.
3. Signal indicator CH B..
4. Audio level CH B.
5. Audio level CH A.
6. Signal indicator CH A.
7. Volume CH A.
8. Antenna CH B.
9. Exit MIX
10. Exit B
11. Output A.
12. AC input.
13. Antenna CH A.
14. MIC jack.
15. MIC output.
16. MIC alloy button.
17. MIC output selector.
18. DC Input

Front and Rear Panel – Other Features

1. Receiver ON button
2. Volume CH B..
3. Signal indicator CH B.
4. Audio level CH B.
5. Audio level CH A
6. Signal indicator CH A
7. Volume CH A.
8. Antenna CH B.
9. Exit MIX.
10. Output B
11. Output A.
12. AC input.
13. Antenna CH A.
14. MIC socket
15. MIC output
16. MIC alloy button

Operation

1. Place the receiver near the audio adjustment, connect the force and the directional cable on the mixed A+B+Cou outputs connect on the Aou output on the B output separately with the two signal cables, and then connect the amplifier or microphone adjuster by connecting the two antennas
   Turn it on and the power indicator will light up and the receiver will turn on in standby mode.

2. Remove the cover from the battery compartment, put the batteries on, and close the lid.

3. Turn the key to the ON position, the indicator will light up for a moment indicating that the receiver signal channel is available meaning it is transmitting to the microphone receiver. Adjustment volume knob on the amplifier keeping it low. Speak into the microphone and adjust the output signal level.

4. Place the microphone button in the STAND BY position. The unity goes into silent mode, interrupting voice output and protecting the noise output.

5. If the indicator on the microphone remains lit for a long time means the battery is low and must be replaced.

6. There are three 6.35mm jacks on the receiver suitable for different types of transmission equipment. In case of If you need two-way audio adjustment, use CH ACH B or the audio terminal exit.

SYSTEM MODULES

Security

• READING GUIDELINE: Read the instructions for use and safety before using the product.
• STORAGE GUIDELINE: Keep this manual in a safe place for future consultation.
• WARNING: Be aware of warnings about the operation of this product.
• USE AND STORAGE: Do not store the product in very humid places with strong magnetic fields, or directly under sunlight or at high temperatures. If you do not use for long periods,
• Remove the power and signal boxes and also remove the batteries from the microphones.
• CLEANING: Do not use liquids or sprays, only a damp cloth
• ACCESSORIES: Use only accessories manufactured or authorized by the manufacturer.
• FOOD: The feeding of this product is that indicated by the manufacturer.
• MAINTENANCE: Do not attempt to repair this product because of the risk of electric shock. Only authorised by the manufacturer shall be used.
• CHANGE OF PIECES: If there is a need to exchange pieces, these must comply with the manufacturer’s specifications or original parts to avoid risk of fire or electric shock.
• SECURITY CHECKING: Verify that the safety requirements are met after any maintenance.
• ADJUSTMENT: If the product is damaged or partially functioning, seek only the manufacturer’s recommended technical assistance

Specifications

RECEPTOR

• Operating frequency: 534-598 Mhz
• Frequency deviation <0,002% with 15ppm crystal control
• Sensitivity: 6uV
• S/R ratio: >55dB
• Audio Output: 0-300mV
• Canais de recep^ao: 2
• Voltage: 220(110) VAC +-10%
• Power: 200mA
• Antena: Antena omini directional

TRANSMISSOR

• Operating frequency: 534-598 Mhz
• Frequency deviation: <0,002% with 15ppm crystal control
• Electrical current consumption: <25mA
• Content band: < Main band 40dB
• Modulation: FM
• Microphone: 600 0hms single via
• Battery: 3 V
• Antena: Interna

SUMMARY

• Moving range:>55dB
• T.H.D:<5%
• Frequency response: 12KHz (+/- 3dB)

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
THE PURSUIT OF THE PERFECT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>