winco CO-1 Can Opener Instruction Manual

: June 1, 2024
: WINCO

Table of Contents

winco CO-1 Can Opener
Product Information
Product Usage Instructions
Replacement Parts List
OPERATING INSTRUCTIONS
CLEANING INSTRUCTIONS
WARRANTY INFO
MOUNTING INSTRUCTIONS
REPLACEMENT PARTS INSTRUCTIONS
Documents / Resources

winco CO-1 Can Opener

winco-CO-1-Can-Opener-PRODUCT

Product Information

Specifications

Brand: Winco
Model: CO-1
Material: Stainless Steel

Product Usage Instructions

Operating Instructions

Make sure the can opener handle is in the unlock position (Figure 1) and slide it up to place a can underneath the metal base (Figure 2).
Hold the can against the opener’s bar with a height distance of 3 between the blade and the top of the can (Figure 3).
Grip the handle firmly and push down onto the can to puncture it (Figure 4).
Lock the handle (Figure 5) and turn it clockwise. Use your free hand to guide the can as it rotates. Continue turning until the top of the can is removed (Figure 6).
Raise the handle to unlock the position and lift it to slide the open and out.

Cleaning Instructions

Use a stainless cleaning brush to remove food and can opening residue from the gear, gear cavity, and knife blade.
Wash the knife, gear, and any splash area with warm soapy water. Do not allow components to soak.
Thoroughly dry all parts using a dry cloth or paper towel.
Coat the knife and gear with light non-sticking vegetable oil when not in use to prevent rusting.

FAQ

Warranty Information

Replacement parts are available for purchase on our website.
Please visit www.wincous.com for an up-to-date parts list and prices.

Important Note

The knife of this opener may be reversed for double wear but should not be reshaped.

Mounting Instructions

Tools Required

1/8 cobalt or titanium drill bit
9/32 cobalt or titanium drill bit
7/16 socket, box, or open-end wrench

Place the L-bracket on the stainless steel table in the desired position.
Mark the center of each mounting hole on the L-bracket for drilling.
Drill starter holes with a 1/8 bit, then complete with a 9/32 bit for stainless steel.
Insert screws through the bracket and tighten with washers and lock nuts using a 7/16 wrench.

Note: Mounting instructions for wooden tables are not included in this manual.

Contents/parts list Included with the product

Can Opener
- (with Blade and Gear)
Can Opener Base
- Installation Kit for Wood Tables
Installation Kit for Stainless Steel Tables

Replacement Parts List

CO-1B: Replacement Blade Set
- CO-1BS: Blade Screw Set CO-1G: Replacement Gear CO-1WI: Installation Kit for Wood Tables
- CO-1SI: Installation Kit for Stainless Steel Tables

OPERATING INSTRUCTIONS

Make sure the can opener handle is in the unlock position (Figure 1) and slide it up enough to place a can underneath it on the metal base. (Figure 2)
Hold the can against the bar of the opener with a height distance of 3″ between the blade and the top of the can. (Figure 3)
Grip the handle firmly and thrust it down onto the can to puncture it. (Figure 4)
Lock the handle (Figure 5) and turn it clockwise. This will automatically turn the can around. Use your free hand to guide the can as it rotates. Continue turning the handle until the top of the can is removed. (Figure 6)
Raise the handle to unlock the position and lift it to slide the opened can out. (Figure 1)

IMPORTANT NOTE: The knife of this opener may be reversed for double wear but should not be reshaped.

CLEANING INSTRUCTIONS

The can opener must be cleaned daily or after each extended use. Regular maintenance will help prevent unwanted build-up and harmful bacteria growth.

Use a stainless cleaning brush to remove all the food and can opening residue from the gear, the gear cavity, and the knife blade.
Wash the knife, gear, and any splash area on the opener using warm soapy water. Do not allow components to soak.
Thoroughly dry the knife, gear, and can opener using a dry cloth or paper towel.
Coat the knife and gear with light non-sticking vegetable oil to prevent rusting when the can opener is not in use.

WARRANTY INFO

Winco warrants these products to be free from defects in material and workmanship for a period of one year from the date of purchase.
The Company’s obligation under this warranty is limited to repairing or replacing without charge any part or parts found to be defective under normal use.
It is the sole responsibility of the purchaser to return the entire unit to the distributor, and transportation charges prepaid.
This warranty does not cover parts that must be replaced under normal use, including, but not limited to, blades and gears on can openers.
No other warranty, written or verbal, is authorized by the Company.
Warranty information outside the United States may vary; please consult your distributor.

REPLACEMENT PARTS

Replacement parts are available for purchase. Please check our website for an up-to-date parts list and prices: www.wincous.com.

MOUNTING INSTRUCTIONS

Mounting can opener on a stainless steel table Tools required for mounting on a stainless steel table
1/8″ cobalt or titanium drill bit
9/32″ cobalt or titanium drill bit
7/16 socket, box, or open-end wrench

Mounting instructions

Place the L-bracket on the stainless steel table in the desired position where you want to secure the can opener.
Mark the center of each of the three mounting holes of the L- bracket. These three points will be your drilling location.
- IMPORTANT
To prevent the drill from slipping out of position, place a piece of masking tape on each of the three marked points. Then mark the points again on the masking tape.
Drill a small starter hole on each marked point with a 1/8” cobalt or titanium drill bit that is specifically used for drilling into stainless steel.
Complete drilling the holes for the screws by using a 9/32” cobalt or titanium drill bit that is specifically used for drilling into stainless steel.
Insert size 1/4 x 20 x 3/4” screws through the L-bracket. Use the split washers and nylon lock nut provided.
Use a 7/16” socket, bow, or open-end wrench to tighten and secure the screws.

Mounting can opener on a wooden table (standard 2″ thick)

Tools required for mounting on a standard 2” thick wooden table
9/32″ drill bit
7/16 socket, box, or open-end wrench

Mounting instructions

Place the L-bracket on the stainless steel table in the desired position where you want to secure the can opener.
Mark the center of each of the three mounting holes of the L- bracket. These three points will be your drilling location.
Drill through each point with a 9/32” drill bit.
Insert size 1/4 x 20 x 2-1/2” screws through the L-bracket. Use the split washers and nylon lock nut provided.
Use a 7/16” socket, bow, or open-end wrench to tighten and secure the screws.

REPLACEMENT PARTS INSTRUCTIONS

Instructions for replacing gear

Stand facing opener on the gear side with the handle lowered. (Figure 7)
Wedge a flat-headed screwdriver into the slot on the right side of the gear to keep it from turning. (Figure 8)
Gently turn the handle counterclockwise to unscrew. (Figure 9)
Remove used gear and washer.
Insert the new gear and washer into the slot. Make sure the printed side of the gear is facing out. (Figure 10)
Position the screwdriver on the left of the gear. (Figure 11)
Turn the handle clockwise to screw it on. Do not over-tighten. (Figure 12)

Instructions for replacing knife blade

Make sure the handle is raised before removing the two screws holding the old knife blade. (Figure 13)
Place the new knife blade on the holder and then the support plate over the knife blade. (Figure 14)
Align holes and refasten the two screws. (Figure 15)
Do not remove or adjust any other parts of the opener.

IMPORTANT NOTE: At the first sign of wear, the knife blade must be replaced with a new factory blade to ensure safe and optimal operation.
Do not attempt to sharpen old knife blades to reuse them.
WINCO www.wincous.com