Tenda AC650 Auto-Install Mini Wireless Dual Band Adapter User Guide
- June 3, 2024
- Tenda
Table of Contents
Quick Installation Guide
AC650 Auto-Install Mini Wireless Dual Band Adapter
Packing List
- Wireless USB adapter * 1
- Quick Installation Guide * 1
If any item is incorrect, missing, or damaged, please keep the original
package and contact the local reseller or distributor immediately.
This Installation Guide only provides guidance for installation.
For detailed product information or more functions, please access
http://www.tendacn.com.
Install the Wireless USB Adapter
-
Connect the wireless USB adapter to a USB port on your computer.
Note
This driver-free wireless USB adapter is compatible with mainstream operating systems, including Windows XP/7/8/8.1/10 -
Click Run Setup.exe.
Installation begins. Please wait. When the progress bar reaches 100%, the installation wizard disappears.
Wait until the following notication appears in the lower-right corner of the desktop, and connect to a WiFi network.
Note
If installation fails, refer to Appendix.
Connect to a WiFi Network
You can connect to a WiFi network after successful installation of the wireless adapter.
-
Select the WiFi network to be connected, such as Tenda_01.
-
Enter the password, and click OK.
Connected.
Appendix
-
If the AutoPlay dialog box does not appear, perform the following procedure (example: Windows 7):
a. Double-click Computer on the desktop.
b. Double-click CD Drive (X:) Wireless to start installation. -
If your computer does not recognize the CD drive, perform the following procedure (example: Windows 7):
a. Click Start and then Control Panel.
b. Click Uninstall a program.
c. Uninstall the other driver-free wireless USB adapters, and reconnect this wireless USB adapter to start installation.
Safety and Emission Statement
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
NOTE: (1) The manufacturer is not responsible for any radio or T V interference caused by unauthorized modications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment
type U9 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
Operate Frequency: 2.4G: EU/2400-2483.5MHz (CH1-CH13)
EIRP Power (Max.): 12.9dBm
Software Version: 1.0.3.2
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
Caution:
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment.
Operating temperature: 0°C~40°C
Operating humidity: (10-90)%RH, non-condensing
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen,
China. 518052
USA hotline: 1-800-570-5892
Toll Free: Daily-9am to 6pm EST
Canada hotline: 1-888-998-8966
Toll Free: Mon – Fri 9 am – 6 pm PST
Email: support.usa@tenda.com.cn
HongKong Hotline: 00852-81931998
E-mail: support@tenda.com.cn
Global Hotline: +86 755-2765 7180 (China Time Zone)
Toll Free: Daily-9am to 6pm EST
Website: http://www.tendacn.com
Copyright
© 2018 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co.,
Ltd. Other brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders. Specifications are subject
to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>