ACECAR G10 GPS Speed Meter User Manual
- June 9, 2024
- ACECAR
Table of Contents
ACECAR G10 GPS Speed Meter
Instruction
Warning: This product working voltage is 5V, and it is forbidden to use a voltage higher than 5V for power supply.
Display functions
- Multi-function display: clock, driving time, travel distance, satellite numbers, acceleration time, longitude, latitude,Dial left or right to switch
- Function icons: fatigue driving, driving time, clock, acceleration time, direction angle, longitude, latitude, driving distance, altitude
- Speed progress bar
- Speed display
- Speeding alarm icon
- Vehicle speed unit (MPH=mile ,Km/h=kilometer), compass, satellite number icon
- The compass can be used normally after the satellite is searched, (N=North, E=East, W=West, S=South)
- The GPS satellite icon stops flashing before it can be used normally
- Satellite numbers
Wave button function
- Short press in: confirm the option after entering the setting menu
- long press in: enter the setting, after adjusting, press vertically for 2 seconds to save and exit
- Push left:: switch clock, driving time, acceleration time (move option after entering setting)
- Long push left: push left for 2 seconds to turn off the buzzer alarm, do it again to turn on
- Push right: switch driving distance, altitude, longitude, latitude (move option after entering the setting)
Enter setting mode
Long press in to enter into the setting mode, press right to choose the menu, and short press in to confirm. Once finishing the setting, long press in to exit.
Menu| Function| Adjustment range| Explanation| Default
value| Set parameter value interface
---|---|---|---|---|---
1| speed| 50-150| Adjust the parameter value when there is an error between
HUD and dashboard.
Ex: dashboard displays 100 KM/H, HUD displays 105 KM/H. Please adjust the parameter value to
102.(107-5)
| 105|
2| Section 1 over speed alarm| 0-250| When the vehicle speed reach to 150KM/H,
HUD will give the alarm| 150|
3| Section 2 over speed alarm| 0-250| When the vehicle speed reach to 180
KM/H, HUD will give the alarm| 180|
4| Section 3 over speed alarm| 0-250| When the vehicle speed reach to 200
KM/H, HUD will give the alarm| 200|
5| Fatigue driving alarm| 1.0-8.0| HUD will give fatigue driving alarm each 8
hours| 8.0|
6| Brightness adjustment| 0-11| 0=automatic sensitivity adjustment
1-11=manual adjustment
| 0|
7| Speed unit| 0-1| 0=KM/H (kilometers) 1=MPH (miles)| 0|
8| Time Adjust| 0:00-12:00| When the device searched the satellite
successfully, adjust the device time as your local time and exit.| 0|
9| Factory reset| 0-1| default=0,
→1, long press in for 2 seconds to save and exit
| |
GPS FAQ
The screen without any display, and no power
Check whether the USB cable is damaged, replace the USB cable for testing, and
prohibit the use of voltage higher than 5V for power supply
Without car speed
After HUD power-on, the satellite icon flashes will start to find the
satellite. Please driving the car to the road. It will work after it stops
flashing
Inaccurate time
When the device search the satellite successfully(the default 8:00 will change
to China local time), set it to your local time and save and exit.
Speed is not correct
- If the unit is correct,km KM/mile MPH, (speed unit switch reference settings item)
- The car factory had increased speed(5-7%)than real for drivers’ safety,satellite data is strictly follow the international standards
- The speed adjustment steps are as follows:
After the GPS speedometer is displayed normally, press and hold the scroll wheel button vertically for 3 seconds to enter item 1 (1-9), then toggle the scroll wheel button left and right to adjust the speed (default is 107. Then your car speed is 30MPH, and the speed of GPS speedometer is 35MPH, then you need to toggle the scroll wheel button to the left to adjust “107” to “102”. On the contrary, if your car speed is 33MPH and GPS speed is 30MPH, you need to toggle the wheel button to the right to adjust “107” to “110”), and finally press and hold the wheel button vertically for 3 seconds to save.
Driving direction display error
After the vehicle speed exceeds 5KM / H, the direction can be displayed
normally.
Speed is still displayed after the car stops
Under the underground parking lot, tunnel, under the overpass, there will be
unstable satellite drift when there is obstruction.
Turn off the buzzer
Push left for 2 seconds to turn off the buzzer, do it again to turn on.
Switching of unit KM/H and MPH
After the GPS speedometer is displayed normally, press and hold the wheel
button vertically for 3 seconds to enter item 1 (1-9), then press the wheel
button vertically to switch to item 7, then toggle the wheel button left or
right to adjust to the desired unit (“1” is MPH, “0” is KM/H), and finally
press and hold the wheel button vertically for 3 seconds to save.
Brightness adjustment
The brightness can also be adjusted, step by step as follows:
After the machine is turned on and displayed normally, press and hold the
scroll wheel button vertically for 3 seconds to enter item 1 (1-9), then press
the scroll wheel button vertically to switch to item 6 (0-11. 0=automatic
sensitivity adjustment, 1-11=manual adjustment), then adjust the brightness to
the left or right according to your needs. Finally, press and hold the scroll
wheel button vertically for 3 seconds to save.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>