PDi PD168-086 J-Hook Articulating Mount Instruction Manual

June 22, 2024
PDi

MODEL NUMBER:
PD168-086 & PD168-087 &
PD168-089
Installation Instructions
Document Number:
PD196-441R2

PD168-086 J-Hook Articulating Mount

Scope:
To Mount a PD168-086 J-Hook Mount to a 100×100 VESA, 100×200 VESA or 200×200 VESA TV in a PDI-179 or PDI-179AV wall mount or to mount a PD168-087 J-Hook Mount to a 400×400 VESA TV in a PDI-179 or PDI-179AV wall mount or to mount a PD168-089 J-Hook Mount to a 200×300 VESA or a 200X400 VESA TV.
Notes:

  1. The maximum capacity for this mount is 55 pounds.
  2. This mount cannot be used with a PDI-A55A TV, due to the VESA pattern, contact PDi using information at the end of the document for questions.
  3. The TVs used in the graphics are used as reference only and are not included with the kits listed.

Tool List:

  1. P1 or P2 Phillips Screwdriver
  2. 1/8” Hex Wrench
  3. Safety Glasses/Goggles

Safety Steps:

  1. Always wear safety glasses/goggles to prevent injury from debris.
  2. Follow the installation/removal instructions for your existing products.

VESA Pattern Chart:

PDi TV VESA Pattern (mm)
PDI-A24 100×100
PDI-A32 100×200
PDI-A43 200×200
PDI-A55 400×400
PDI-A65 200×300

PD168-086 Installation Instructions
Bill of Material:

Item Part Number Description QTY
1 PD168-086 J-Hook Articulating Mount 1
2 PDIPPHMSM6X110 Screw, Phillips Pan Head, M6-1 x 10mm 4

Procedure:

Step 1:
Mount the wall mount, PDI-179 or PDI-179AV, to the wall following the installation instructions included with the mount, (PD196-047 or PD196-396).
Step 2:
Attach the J-Hook mount, PD168-086, (#1) to the TV using four (4) screws, PDIPPHMSM6X110, for PDi TVs with a 100×200 VESA or a 200×200 VESA as shown below. Be sure to align the correct slots on the J-Hook mount, PD168-065, with the VESA pattern on the back of the TV, see reference dimensions below.
Note: Use customer supplied M-4 screws to mount a PDi TV with a 100×100 VESA.PDi PD168-086 J-Hook Articulating Mount

Step 3:
Seat the J-Hook Mount, PD168-086, (#1) into the wall mount, PDI-179 or PDI- 179AV, and tighten the pilfer proof screw.
Step 4:
To adjust the tilt of the TV, support the weight of the unit and loosen both adjustment screws, one on each side shown below, using a 1/8” hex wrench and adjust to the desired tilt. Tighten the adjustment screws down once the desired tilt has been achieved until the TV remains in place.
Note: Only loosen the adjustment screw! Loosening the non-adjustment screws could cause the TV to fall.PDi PD168-086 J-Hook Articulating Mount -
figPD168-087 Installation Instructions
Bill of Material:

Item Part Number Description QTY
1 PD168-086 J-Hook Articulating Mount 1
2 PDIPPHMSM6X110 Screw, Phillips Pan Head, M6-1 x 10mm 4
3 PD181-881 Plate, Mounting, 400 x 400 VESA, Right 1
4 PD181-882 Plate, Mounting, 400 x 400 VESA, Left 1
5 PDIFW10 Washer, Flat, #10 4
6 PDINILN1032 Nut, Nylok, #10-32 4
7 PDIPPHMSM8X20 Screw, Phillips Pan Head, M8-1.25 x 20mm 4

Procedure:
Step 1:
Attach the mounting plates, PD181-881 (#3) and PD181-882 (#4), to the back of the TV and attach to the TV with four (4) screws, PDIPPHMSM8X20, (#7).
Step 2:
Attach the J-Hook mount, PD168-086, (#1) to the mounting plates, PD181-881 (#3) and PD181-882 (#4), using four washers, PDIFW10, (#5) and four (4) nuts, PDINILN1032, (#6) as shown. Once this is complete, follow steps 3 and 4 above.PDi PD168-086 J-Hook Articulating Mount - Hook
mountPD168-089 Installation Instructions
Bill of Material:

Item Part Number Description QTY
1 PD168-086 J-Hook Articulating Mount 1
2 PD181-910 Plate, Adaptor, 200mm to 300mm or 400mm 2
3 PDIFWM6 Washer, Flat, M6 4
4 PDINILNM6 Nut, Nylok, M6-1 4
5 PDIPPHMSM6X116 Screw, Phillips Pan Head, M6-1 x 16mm 4

Procedure:
Step 1:
Attach the adaptor plates, PD181-910 (#2), to the back of the TV and attach to the TV with four (4) screws, PDIPPHMSM6X116, (#5).
Step 2:
Attach the J-Hook mount, PD168-086, (#1) to the mounting plates, PD181-910 (#2), using four washers, PDIFWM6, (#3) and four (4) nuts, PDINILNM6, (#4) as shown. Once this is complete, follow steps 3 and 4 above. PDi PD168-086
J-Hook Articulating Mount - fig 1
Limited Warranty
PDi Communication Systems Inc., (“PDi”) standard warranty information is found at PDiarm.com. For information regarding authorized servicing and all other information pertaining to this warranty, please contact PDi COMMUNICATION SYSTEMS, INC. at 40 Greenwood Ln, Springboro, Ohio 45066 or phone 800-628-9870 and ask for the PDi ProServices team.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals