BN-LINK Mini Wireless Remote Control Outlet Switch User Guide
- June 8, 2024
- BN-LINK
Table of Contents
BN-LINK Mini Wireless Remote Control Outlet Switch
PRODUCTS VIEW
FEATURES
- Easily controlled by the remote control from up to 100 feet in line-of-sight.
- Separate on and off buttons on the remote control.
- Outlets will remain powered off after a power outage to save energy.
- Power output up to 1250W at 125V(60Hz).
- Low power consumption, reduces energy use and extends product life by up to 15%.
- Manual pairing and unpairing.
SETUP
- Install one 12V/23A battery in the remote control’s battery compartment, making sure the polarity of the battery is correct.
- Plug each outlet switch into a socket and plug a device or appliance into each outlet.
- Press the on/off buttons for the respective channel on the remote control to operate the outlet switch.
NOTES
- Regularly change the battery in the remote control for best performance. If you find the outlet switches are not responding or the LED indicator on the remote control becomes dim, the battery should be replaced. Always dispose of old batteries properly with consideration for the environment.
- Make sure the battery and outlets are installed firmly and correctly for safe operation.
- These outlet switches are for indoor use only. Avoid exposure to high-temperature sources, strong sunlight and moisture. The outlets are best used in air as with good air circulation.
- Do not exceed the maximum load current of 1 0A(Approximately 1250W).
PROGRAMMING THE OUTLETS
Notes: The outlets are pre-programmed for immediate use, but the configuration can be customized to meet your needs.
To program a remote control transmitter and outlets switch receiver:
- Remove the outlet receiver from the power socket, then plug the outlet receiver back into the power socket.
- Press and hold the “Learning & ON/OFF” button till the indicator start to flash.
- Release the “Learning & ON/OFF” button, and press and hold the corresponding “ON” button on the remote until you hear a “click”.
- The indicator will stop flashing indicating that the pairing is successful.
RESETTING AN OUTLET
Should you wish to unpair an outlet receiver from the remote, or if your outlets are unresponsive to the remote, the outlets can be reset following below steps.
- Remove the outlet receiver from the power socket.
- Press and hold the “Learning & ON/OFF” button on the outlet receiver.
- While still holding the button, plug the outlet receiver to a power socket and wait to see the indicator to flash.
- When the indicator stops flashing, you may release the button, and the reset process is now complete.
- You may program the outlet after resetting.
TROUBLESHOOTING
In the case that one or more of the outlet receivers do not respond to the remote control, please follow the steps given below to resolve the issue:
- Check to see if the battery of the remote is low and needs replacement.
- Make sure that the outlet receiver is correctly placed in the power socket.
- Make sure that the outlet receiver is used in an area with proper air circulation to avoid overheating.
- Reset and program the outlet(s).
TECHNICAL DATA
- Voltage ……………………………. 125V~60Hz
- Max. power ……………………….. 10A 1250W
- Transmission frequency …….. .433.92MHz
- Remote battery ……………………. 12V (23A)
SUPPORT
CENTURY PRODUCTS INC. 3545 Granada Ave El Monte Ca 91731 Custom Service
Assistance: 1.909.592.1881
E-mail: support@bn-link.com www.bn-
link.com
Hours: 9AM – 5PM PST, Mon – Fri Designed in California Made in China
FAQs
How do I pair the remote control with the outlet switches?****
Please press the pairing button on the remote control for 3 seconds until the LED indicator flashes. The LED indicator will flash for 10 seconds, indicating that it is in pairing mode. Then press the pairing button on the remote controller and hold it for 3 seconds until the LED indicator flashes. The LED indicator will flash rapidly, indicating that it has been paired successfully.
How do I unpair the remote control from the outlet switches?****
Please press the pairing button on the remote control for 3 seconds until the LED indicator flashes. The LED indicator will flash for 10 seconds, indicating that it is in pairing mode. Then press and hold down both on and off buttons on the remote controller for 3 seconds until the LED indicator flashes rapidly, indicating that it has been unpaired successfully.
How many devices can be controlled by a single remote control?****
You can control up to 4 devices by a single remote control. When you press a channel button, you can see its corresponding device number displayed on screen. When you press a channel button again, you can see another device number displayed on screen.
Have these plugs ever ignited an outlet or generated a spark?****
My best hunch is that the switching outlets have a 10 A rating. A spark could result if you attempt to switch anything that draws more than 10 A. Additionally, motors that draw close to 10 A may briefly exceed 10 A during startup, which could result in a spark.
How do wireless electrical outlets work?****
A small Wi-Fi-enabled power adaptor called a “smart plug” is plugged into a standard wall outlet and manages the electricity supply to connected devices. Once configured, a smart plug can be operated using an app on your phone or tablet, a smart speaker, or a smart display.
How do remote control outlets work?****
You can use your phone to remotely operate plugged-in gadgets utilising remote control outlets that link to your wifi network. You may use your voice to operate the smart remote control outlets when linked to a voice assistant like Alexa or Google Home.
Are wireless outlets safe?****
Not typically. The same safety standards that apply to other plugged-in devices also apply to smart plugs. As with any electrical gadget, as long as you don’t overload the outlet, you should be safe.
Do remote plugs save energy?****
Standby savers, often known as energy-saving plugs, operate by remote. When the remote control button is pressed, the device, which is plugged in between the appliance and the socket, prevents electricity from passing from the socket to the appliance.
Do smart outlets work without wifi?****
The Smartwave plug does really function without Wi-Fi, but only after initial configuration. Even when there is no Wi-Fi connection, the Smartwave plug will automatically turn on and off your appliances and electronics since it stores its programming internally.
Is it functional if the outlet is concealed by a couch?****
Yes. A queen foam mattress is positioned in front of and immediately to the right of mine. Compared to most couches, that is much denser.
What is the frequency of operations?****
The frequency of operation is 433.92 MHZ.
I’ve changed outlets. Does the module remember the brightness setting if I dim the lights, turn the power off, and then turn it back on?****
My lamp has two settings, and when I turn it back on, it turns on in the last setting I had it in. I believe it should remember this.
Video
Download PDF Link;BN-LINK Mini Wireless Remote Control Outlet Switch pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>