AMERICAN LIGHTING NFPRO360 Single Color LED RGBW Light Instruction Manual

: June 21, 2024
: American Lighting

Table of Contents

INSTALLATION INSTRUCTIONS
SAFETY INFORMATION
CARE AND MAINTENANCE:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**AMERICAN LIGHTING NFPRO 360 Single Color LED R G B W Light Instruction Manual

**

INSTALLATION INSTRUCTIONS

WARNING
These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (N E C ) .
WARNING Use this fixture with a 24V DC power supply only (sold separately). Any other power supply may damage the fixture.
WARNING
To reduce the risk of fire, electric shock or injury to persons, use this flexible light only with American Lighting/Prizm recommended drivers, controllers, power connectors, splices and extensions.
Do not operate Neo Flux Pro while it is coiled or on the reel.
WARNING

To reduce the risk of fire, electric shock or injury to persons, make sure that the electrical power to the fixture is disconnected at the source prior to installation or any servicing.

SAFETY INFORMATION

Read all installation instructions before beginning; if not qualified, do not attempt installation. Contact a qualified electrician.
To reduce the risk of fire, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this product. Save these instructions for future use.
Do not cover this product as the covering may cause product to overheat, melt, or ignite.
Risk of fire or electric shock. Uncoil flexible light prior to plugging in. Do not operate NeoFlux Pro while it is tightly coiled.
Do not route the cord or NeoFlux Pro through walls, ceilings, doors, windows, or any similar part of the building structure.
Secure this flexible light using only factory recommended mounting channel (NFPROV-CHAN-1 M), sold separately.
Do not secure this product or its cord with staples, nails, or like means that may damage the outer jacket or cord insulation.
Do not use if there is any damage to the housing or power cord insulation. Inspect periodically.
Do not install on gates or doors, where subject to continuous flexing.
Do not install near flammable liquids or other flammable materials.
Follow instructions carefully when cutting NeoFlux Pro. Ensure all end caps are properly sealed.
24V NeoFlux Pro can only be cut at specific intervals as indicated by the cutting marks printed on the side of the housing (50mm or 1.97”). Failure to cut at a cut mark will result in a loss of light. Before making any cuts, be sure power source is disconnected at the source!
This product is designed for use by a qualified installer.
This product is for decorative use only. Not to be used by children as a toy. Keep out of reach of small children.
Do not exceed maximum run distance in any single inter-connected run: 5m (16.4ft).
Size your 24V DC driver appropriately for your run distance of NeoFlux Pro using 10W/m or 3.05W/ft (static white/single color) and 15W/m or 4.87W/ft as a guide. Be sure not to load any driver to 100% as this will reduce its efficiency. A 90% maximum load is recommended for driver longevity.
The rated ambient temperature range for NeoFlux Pro is -25°C (-13°F) to 45°C (113°F).
The maximum bend radius of NFPROD series product is 20cm or 7.86”. Do not twist, drop, hang, sag, or bend product in any way other than intended. See Figure 1 below for reference.

20 CM BEND RADIUS

CARE AND MAINTENANCE:

For cleaning, use a soft, dry or damp cloth. Do not use harsh chemicals or abrasives.

RECOMMENDED 2-PERSON INSTALLATION FOR LENGTHS GREATER THAN 2 M

LAYOUT CONSIDERATIONS:

It is recommended that installation be performed by at least 2 persons to ensure proper handling of linear product and prevent damage to the internal and external construction. See Figure 1.
Determine the desired locations and lengths of NeoFlux Pro to be installed. Use this information to determine locations and sizes of 24V DC power supplies.
There are many different mounting accessories available for NeoFlux Pro 360. See pages 3-9 for installation methods.

CONNECTING POWER (Figures 2 & 3):
Disconnect power at the source prior to attempting installation or service of product. Use this fixture with appropriate 24V DC power supply only. Any other power supply may damage the fixture.

Connect a 24V DC power supply to the beginning of the NeoFlux Pro run using the conkit attached in the previous section.
See Figure 2 for single color (2pin) wiring diagram. See Figure 3 for RGBW (5pin) wiring diagram. See Figure 8 for Dynamic RGBW wiring diagram.
Connect the 24V DC power supply to line voltage. Single color NeoFlux Pro does not require a controller, however, RGBW NeoFlux Pro will require a form of RGBW control for color changing capability. NeoFlux Pro is compatible with DMX control options.

JOINER CONNECTORS :
Use when connecting two independent pieces of Neo Flux Pro 360 end-to-end.

PZM-NFPR O 360-JOINA Connector for Side Cable Entry
Insert the lead end of the first light and the tail end of the second light into the connector. Ensure cable is seated in slot opening.
Lock the connectors with self-tapping screws (included). Each end cap is secured with 4 screws.
Complete.
PZM-NFPRO 360-JOINB
Connector for Closed End
Insert the tail ends of 2 light sections into the connector.
Lock the connectors with self-tapping screws (included). Each end cap is secured with 4 screws.
Complete.

SURFACE MOUNT – OPEN CLIPS:

SURFACE MOUNT – TRACK PROFILE:

SUSPENDED HORIZONTAL MOUNT – OPEN CLIPS:

SUSPENDED HORIZONTAL MOUNT – TRACK PROFILE:

SUSPENDED VERTICAL MOUNT – SINGLE SURFACE:

SUSPENDED VERTICAL MOUNT – DUAL SURFACE U-SHAPE:

SUSPENDED VERTICAL MOUNT – SINGLE PENDANT:

SURFACE MOUNT – CLOSED CLIPS:

SUSPENDED ADJUSTABLE MOUNT – OPEN CLIPS:

SUSPENDED ADJUSTABLE MOUNT – TRACK PROFILE:

SUSPENDED ADJUSTABLE MOUNT – CLOSED CLIPS:

SUSPENDED ADJUSTABLE MOUNT – CONCEALED LOCKING CLIPS: