PROCET PT-PCGI-BT Gigabit PoE to USB-C Adapter Installation Guide
- June 21, 2024
- PROCET
Table of Contents
PROCET PT-PCGI-BT Gigabit PoE to USB-C Adapter
Specifications
- Input Power pins: 44-57Vdc
- Output USB Standard: 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A
- Network Protocol: IEEE802.3 i/u/ab
- Data Speed: 10/100/1000Mbps
- Operating Temp.: -20 to 55°C
- Operating Humidity: 20% to 80% non-condensation
- Operating Altitude: Up to 2000 meters
- Storage Temp.: -20 to 70°C
- Storage Humidity: 10% to 90% non-condensation
- IP Rated: IP40
- Dimensions & NW: 98.7mm X 73.72mm X 19mm, 167g
Product Usage Instructions
1. Introduction
This section provides an overview of the product and its appearance.
1.1 Introduction
The introduction text goes here…
1.2 Appearance
The product features front, upper, and side views as described below:
- Front View: PoE Input Port, Data Indicator, Power Indicator, USB-C Fixing Holes, USB-C Output Port
- Upper View: Fixing holes, Company Logo Area
- Side View: Description of the side view
1.3 Specification
Detailed specifications of the product are listed under the specifications section above.
2. Installation Preparation
This section details the preparation steps before installing the product.
Frequently Asked Questions
- Q: What type of cables should be used to connect the product?
- A: It is recommended to use Cat5e or Cat6 cables for connecting the product.
- Q: What data rates are required for Gigabit connectivity?
- A: For Gigabit data rates, the Ethernet connectivity should be at least 1000Mbps. The USB-C device and cable should also support Gigabit speeds.
QR Code
Declaration
This document belongs to PROCET company. It is not allowed to be reproduced
and modify without the original author’s permission. It is PROCET’s policy to
improve its products as new technology, components, software, and firmware at
any time. PROCET, therefore, reserves the right to change specifications
without prior notice. Please follow WEEE (Waste Electrical and Electronic
Equipment) disposal instructions for old electronic products. Please do not
dispose of the old product in your general household waste bin.
The symbol indicates that the product should not be discarded as unsorted
waste but must be sent to separate collection facilities for recovery and
recycling.
Overview
The installation Guide for PT-PCGI-BT and mainly introduces the hardware specification, installation methods, and precautions of the installation. There may be differences in the appearance and configuration from other models. All product images in this manual are for illustration purposes only and may differ from the actual product.
This manual includes the following chapters:
- Product Introduction. Including the basic functions and specifications of PT-PCGI-BT, as well as the product appearance and applications introduction.
- Installation Introduction. Introducing the preparation work and precautions before installing the product.
- Product Installation.
For whom
- Network Engineers
- Network Administrators
- Field Technicians
Introduction
PT-PCGI-BT is a gigabit PoE to USB-C power and data all-in-one adapter. It allows for the power and data obtained from an IEEE802.3bt PoE injector or PoE switch to convert to USB-C PD. Support your USB-C device has stable wired network connectivity. It is enclosed in a high-impact black metal housing with mounting holes on both sides for easy installation. Equipped with some thermal pads, good heat dissipation, suitable for industrial environments with a working temperature from -20 degrees Celsius to +50 degrees Celsius. A fixed hole on the top of the USB-C port to 100% fixed the USB-C cable connector not loose. The device supports a safe voltage input range of 44 to 57 Vdc and provides a maximum power output of 60W along with 10/100/1000Mbps network data. The effective distance for PoE transmission via Cat5e/Cat6 Ethernet cable is 100 meters. It is compatible with most USB-C devices in the market. Such as tablets, laptops, cellphones, small PCs/Next Unit of Computing (NUC) interactive information kiosks, smart monitors, cameras, and so on. Many bands of USB-C devices were tested, such as Samsung Galaxy Tablets, Microsoft Surface, Apple iPads, Android tablets/smartphones, some Chrome books, and other USB-C-powered devices consuming up to 60W. When the PoE power is disconnected, the unit of PT-PCGI-BT will get power from your USB-C device and can work as an Ethernet signal converter to continue supporting data transfer.
Appearance
Specification
Installation Preparation
Package Contents
Open the box of the PT-PGCI-BT and carefully unpack it, the box should contain
the following items
Installation Toolkits
These tools may be needed during equipment installation and should be prepared by yourself: level ruler, marking pen, craft knife, wire stripper, network pliers, impact drill, different matching drillbits, rubber hammer, cross screwdriver, wrench, ladder, etc
Inspection
Check if the powered device work normally after the connection
Caution
Please use Cat5e or Cat6 cables to connect this product.
Caution
- We recommend to use Cat5e or above UTP/STP cables for 1000Base-T Ethernet.
- If you would like to have Gigabit data rates, the Ethernet connectivity should be at least 1000Mbps. Your USB-C \device should support Gigabit. Your USB-C cable should be at least 3.0 standard and the cable should be at maximum 3 meters length.
Caution
- This device is for indoor use only.
- For optimal performance of this device, please use Cat 5e or Cat6 cables.
- The total Ethernet cable length can not exceed 100 meters.
- Disconnect the USB-C cable from your USB-C device if it does not need power charged. Because prolonged charging may cause your USB-C devices/Tablets to experience battery swelling or a decrease in battery storage capacity.
- Please use USB 3.0 or higher standard products for connection. Since the practical speed is 35/40MB/s for USB2.0, the practical speed is 300MB/s for USB3.0, the practical speed is 300MB/s for USB3.1 Gen 1, the practical speed is 1.2GB/s for USB3.1 Gen 2. Low and high-standard USB-C devices connecting only apply the lower standard speed.
- If this product needs to be installed in a fixed position, please choose a metal plate or wall for installation. Wooden backboards should not be used to prevent fire hazards.
Installation
This product is primarily used desktops but can also be used for fixed installations.
Wall mounted Installation
This product is safe to use for wall-mounted installation.
- Fix the product with screws and tighten them into the screw holes. As shown in Figure 3-1
Inspection
Inspect the installed equipment before putting it into operation：
- Make sure the PD connected can work normal.
- Make sure the Ethernet cable connection is correct
Creativ e Lianj ie Netw ork Technology Co.Ltd
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>