PROCET PT-PD208GT PoE Splitter Installation Guide
- June 12, 2024
- PROCET
Table of Contents
PROCET PT-PD208GT PoE Splitter Installation Guide
PT-PD208GT PoE Splitter
Quick Installation Guide
Declaration
This document belongs to PROCET company. It is not allowed to reproduce and modify without the original author’s permission. It is PROCET’s policy to improve its products as new technology, com ponents, software, and firm ware at anytime. PROCET, therefore, reserves the right to change specifications without prior notice. Please follow WEEE (Waste Electrical and Electronic Equipment ) disposal instructions for old electronic products.
Please do not dispose of the old product in your general household waste bin.
The symbol indicates that the product should not be discarded as unsorted waste but must be sent to separate collection facilities for recovery and recycling.
Copyright ©2022 Creative Lianjie Network Technology Co.Ltd
All rights reserved.
Overview
The installation Guide for PT-PD208GT and mainly introduces the hardware specification, installation methods, and precautions of the installation. There may be differences in the appearance and configuration from other models. All product images in this manual are for illustration purposes only and may differ from the actual product.
This manual includes the following chapters:
- Product Introduction. Including the basic functions and specification of PT-PD208GT, as well as the product appearance and applications introduction.
- Installation Introduction. Introducing the preparation work and precautions before installing the product.
- Product Installation. Two methods of product installation.
For whom
Network Engineers
Network Administrators
Field Technicians
Introduction
PT-PD208GT is a single-port PoE splitter with a high-impact metal shell. It works as a convert er separating power and dat a from t he PoE source and t hen delivering power and dat a t o non- PoE devices. DIP switch for 12V and 24V adjust able out put volt age. Working for 25W non- PoE PDs, such as power communication stations, wireless APs, network cameras, and other non-PoE terminals. Supporting 10/ 100/ 1000M bps of data speed.
It is powered by IEEE802.3at standard PSE or PoE+ Switch at 30W. The effective distance is 100 meters over Cat5e/ Cat6 cables from data source to terminal device. Isolated design inside to avoid high current input damage. The model is easy to install with two mounting holes.
Appearance
Upper view
Side view
Front view
Specification
Installation Preparation
Package contents
Open the box of the PT-PD208GT and carefully unpack it, The box should contain the following items:
Installation toolkit
These tools may be needed during equipment installation, and should be prepared by yourself: level ruler, marking pen, craft knife, wire stripper, network pliers, impact drill, different matching drilbits, rubber hammer, cross screwdriver, wrench, ladder, etc.
Inspection
- Connect the device to a PoE switch and check the PWR LED to ensure proper function before installation.
- Connect the LAN port to the device requiring network access, such as a computer.
- Connect the DC output to the device requiring 12V/24Vdc power supply, as shown in Figure 2-1.
Caution：
Please use PoE power supply equipment that complies with IEEE802.3af/at/PoE+
to connect this product.
Connect PoE into the PoE switch, PWR LED indicates normal operation.
LAN port to computer for network access, DC port to 12V/24Vdc device for power
supply.
Use DIP switch to control output voltage as needed.
Caution ：
- We recommend to use Cat5 or higher UTP/STP cables for 100Base-TX Ethernet.
- We recommend to use Cat5e or above UTP/STP cables for 1000Base-T or 2.5G Base-T Ethernet.
To ensure better lightning protection for outdoor PD, it is recommended to use PROCET Ethernet surge protection products. For more information, please visit http://www.procetpoe.com
Installation
This product is safe to use for slot-fasten mounted and wall-mounted installation.
Wall mounting
The device will be fixed on the wall with screw into the poles, and the hole diameter should be between 8mm to10mm.
1. Mark the screw hole positions with marking pens.
As showed in 3-1.
2. Drill an 8mm diameter hole at the marked position and fix the expansion bolt into the hole by hitting it with a rubber hammer.
Caution in drilling process ：
- Keep the drill bit pependicular to the wall surface, hold the drill handle tightly with both hands, maintain a steady direction to avoid shaking and damaging the wall or causing the hole to tilt.
- If the wall is too hard and smooth for the drillbit to locate, use a center punch to make an indentation at the hole position to help guide the drillbit.
- The depth of each hole should be consistent.
Slot-fasten mounting
Use the slot-fasten mounting to fix the product on the wall with screws.
1. Loosen the screws and put the product slot into the screw.
As showed in 3-4.
2 Make sure the slot is fixed to the screws tightly and tighten the screws.
As showed in 3-5.
Grounding
PROCET PoE splitter PT-PD208GT has the following grounding solutions for reference during construction:
If the installation is in the computer room, it can be connected to the dedicated grounding busbar in the room. The grounding busbar is a connecting conductor between the grounding bodies of the building, such as flat iron, flat steel, nanomaterial conductors, copper-clad steel, etc. Pls refer to the figure 3-6.
For the safety of personnel and equipment in an environment without dedicated grounding equipment, a simple grounding device can be constructed as follows:
- a. Prepare a 6mm 2 grounding wire or a braided soft copper wire.
- b. Prepare a copper tube or angle iron, or other metal tube, bury it underground to a depth of one meter or more as a grounding electrode.
- c. Use the grounding wire to connect the external grounding terminal of the product to the metal tube. (or angle iron）
Caution ：
Use a galvanized metal pipe buried underground at adepth of one meter or more,
such as a water or sew age pipe ,as an emergency grounding if no other
grounding environment is available.
Inspection after installation
Inspect the installed equipment before putting it into operation：
- Make sure the PoE switch is compliant with our product.
- Make sure the Ethernet cable connection is correct.
Make sure all connections are correct, and turn on the power, inspect all the indicators.
Creative Lianjie Network Technology Co.Ltd
www.procetpoe.com