AOC 22B30HM2 45 VA LCD Monitor User Manual

: June 16, 2024
: AOC

AOC 22B30HM2 45 VA LCD Monitor User Manual

www.aoc.com
©2023 AOC.All Rights Reserved.

Safety

National Conventions

The following subsections describe national conventions used in this document.

Notes, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as foll

NOTE : A NOTE indicates important information that helps you make better use of your computer system.

CAUTION : A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING : A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.

Power

****The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

****Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.

****Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

****To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 5A.

****The wall socket shall be installed near the equipment and shall be easily accessible.

****For use only with the attached power adapter.
Manufacturers:Ten Pao Industrial Co.,Ltd
Model: S025ANP1900131

Manufacturers: TPV ELECTRONICS(FUJIAN)CO.,LTD.
Model: ADPC1925EX

Installation

Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.

****Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

****Do not place the front of the product on the floor.

****If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.

****Leave some space around the monitor as shown below. Otherwise, air- circulation may be inadequate hence overheating may cause a fire or damage to the monitor.

To avoid potential damage, for example the panel peeling from the bezel, ensure that the monitor does not tilt downward by more than -5 degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty.

See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:

Installed with stand

Cleaning

****Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong- detergent which will cauterize the product cabinet.

****When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.

****Please disconnect the power cord before cleaning the product.

Other

****If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.

****Make sure that the ventilating openings are not blocked by a table or curtain.

****Do not engage the LCD monitor in severe vibration or high impact conditions during operation.

****Do not knock or drop the monitor during operation or transportation.

****The power cords shall be safety approved. For Germany, it shall be H03VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly.

****Excessive sound pressure from earphones and headphones can cause hearing loss. Adjustment of the equalizer to maximum increases the earphones and headphones output voltage and therefore the sound pressure level.

Setup

Contents in Box

⁕ Not all signal cables will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.

Stand & Base Setup

Please setup or remove the base following the steps as below.

Adjusting Viewing Angle

To achieve the best viewing experience, it is recommended that the user can make sure they are able to look at their whole face on the screen, then adjust the monitor’s angle based on personal preference. Hold the stand so you will not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor as below:

Note:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.

WARNING:

To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than -5 degrees.
Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.

Connecting the Monitor

Cable Connections In Back of Monitor:

HDMI
Analog (D-Sub 15-Pin VGA cable)
Power

Connect to PC

Connect the power cord to the back of the display firmly.
Turn off your computer and unplug its power cable.
Connect the display signal cable to the video connector on the back of your computer.
Plug the power cord of your computer and your display into a nearby outlet.
Turn on your computer and display.

If your monitor displays an image, installation is complete. If it does not display an image, please refer to Troubleshoot.
To protect equipment, always turn off the PC and LCD monitor before connecting.

Wall Mounting

Preparing to Install An Optional Wall Mounting Arm.

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps:

Remove the base.
Follow the manufacturer’s instructions to assemble the wall mounting arm.
Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.
Insert the 4 screws into the holes and tighten.
Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instructions on attaching it to the wall.

Specification of wall hanger screws:M4*(8+X)mm, ( X=Thickness of Wall mount bracket)

Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official department of AOC. Always contact manufacturer for wall-mount installation.

⁕Display design may differ from those illustrated.
WARNING:

To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than -5 degrees.
Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.

Adaptive-Sync function

Adaptive-Sync function works with HDMI
Compatible Graphics Card: Recommended list is as below, also could be checked by visiting www.AMD.com

Graphics Cards

Radeon™ RX Vega series
Radeon™ RX 500 series
Radeon™ RX 400 series
Radeon™ R9/R7 300 series （R9 370/X, R7 370/X, R7 265 except）
Radeon™ Pro Duo (2016)
Radeon™ R9 Nano series
Radeon™ R9 Fury series
Radeon™ R9/R7 200 series (R9 270/X, R9 280/X except)

Processors

AMD Ryzen™ 7 2700U
AMD Ryzen™ 5 2500U
AMD Ryzen™ 5 2400G
AMD Ryzen™ 3 2300U
AMD Ryzen™ 3 2200G
AMD PRO A12-9800
AMD PRO A12-9800E
AMD PRO A10-9700
AMD PRO A10-9700E
AMD PRO A8-9600
AMD PRO A6-9500
AMD PRO A6-9500E
AMD PRO A12-8870
AMD PRO A12-8870E
AMD PRO A10-8770
AMD PRO A10-8770E
AMD PRO A10-8750B
AMD PRO A8-8650B
AMD PRO A6-8570
AMD PRO A6-8570E
AMD PRO A4-8350B
AMD A10-7890K
AMD A10-7870K
AMD A10-7850K
AMD A10-7800
AMD A10-7700K
AMD A8-7670K
AMD A8-7650K
AMD A8-7600
AMD A6-7400K

Adjusting

Hotkeys

Source/Auto/Exit
Clear Vision/<
Image ratio/>
Menu/Enter
Power

Menu/Enter
When there is no OSD, Press to display the OSD or confirm the selection.

Power
Press the Power button to turn on the monitor.

Image ratio
When there is no OSD, Press > hotkey to active image ratio , Press < or > to adjust 4:3 or wide. (If the product screen
size is 4:3 or input signal resolution is wide format, the hot key is disable to adjust).

Source/Auto/Exit
When the OSD is closed, press Source/Auto/Exit button will be Source hot key function.
When the OSD is closed, press Source/Auto/Exit button continuously about 2 second to do auto configure (Only for the models with D-Sub)

Clear Vision

When there is no OSD, Press the “ <” button to activate Clear Vision.
Use the “ > ” or “>” buttons to select between weak, medium, strong, or off settings. Default setting is always “off”.
Press and hold “ <” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo: on” will be display on the screen for a duration of 5 seconds. Press Menu or Exit button, the message will disappear. Press and hold “ <” button for 5 seconds again, Clear Vision Demo will be off.

Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.

OSD Setting

Basic and simple instruction on the control keys.

Press the Menu-button to activate the OSD window.
Press < Left or > Right to navigate through the functions. Once the desired function is highlighted, press the Menu-button to activate it, press < Left or > Right to navigate through the sub-menu functions. Once the desired function is highlighted, press Menu-button to activate it.
Press < Left or > to change the settings of the selected function. Press to exit. If you want to adjust any other function, repeat steps 2-3.
OSD Lock Function: To lock the OSD, press and hold the Menu-button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD – press and hold the Menu-button while the monitor is off and then press power button to turn the monitor on.

Notes:

If the product has only one signal input, the item of “Input Select” is unable to be adjusted.
ECO modes (except Standard mode), DCR, DCB mode and Picture Boost, for these four states that only one state can exist.

Luminance

Note :
When “HDR Mode” is set to “non-off”, the items “Contrast”, “Eco mode ”, “Gamma” cannot be adjusted.

Image Setup

Color Setup

Note :
When “HDR Mode” under “Luminance” is set to “non-off”, all items under “Color Setup” cannot be adjusted.

Picture Boost

Note :
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.
When “HDR Mode” under “Luminance” is set to “non-off”, all items under “Picture Boost” cannot be adjusted.

OSD Setup

Game Setting

Note :
When “HDR Mode” under “Luminance” is set to “non-off”, the items “Game Mode”, “Shadow Control”, Game Color” cannot be adjusted.

Extra

Exit

LED Indicator

Troubleshoot

Specification

General Specification

Preset Display Modes

Note: According to the VESA standard, there may be a certain error (+/-1Hz) when calculating the refresh rate (field frequency) of different operating systems and graphics cards. In order to improve compatibility, the nominal refresh rate of this product has been rounded off. Please refer to the actual product.

Pin Assignments

15-Pin Color Display Signal Cable

19-Pin Color Display Signal Cable

* Only for certain models

Plug and Play

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.