AeroCool Lux Pro Power Supply Modular User Manual
- June 16, 2024
- AeroCool
Table of Contents
AeroCool Lux Pro Power Supply Modular
Product Specifications
- Brand: LUXPro
- Model: Power Supply
- Compatibility: NON-INDUSTRIAL desktop systems
- Form Factor: INTEL’s Desktop Platform Form Factors
Product Usage Instructions
Before Installation:
- Ensure the wattage and output of the PSU meet your system’s requirements.
- Disconnect the power cord and turn off the PSU switch.
- Avoid usage outside of INTEL’s Desktop Platform Form Factors to prevent overheating or damage.
- Avoid expanding connectors through adapters.
- Avoid operating in wet or damp conditions.
- Do not open the PSU casing as it contains hazardous voltages.
- Do not remove the warranty sticker to avoid voiding the warranty.
Installation Steps:
Step 1: Preparation
Before installing the PSU, unplug the AC power cord and ensure the I/O
panel is off.
Step 2: Connecting 20+4-pin Connector
Connect the 20+4-pin connector to the motherboard. Note that the detachable
4-pin connector is not suitable for ATX12V 4-pin connector to prevent
irreversible damage.
Step 3: Connecting ATX12V Power
Connect the ATX12V (CPU power) 4-pin or 8-pin (by 4+4-pin) connector to the
motherboard as needed.
Frequently Asked Questions (FAQ)
-
Q: Can I use this PSU for industrial systems?
A: No, this PSU is designed for NON-INDUSTRIAL desktop systems only. -
Q: What should I do if I accidentally remove the warranty sticker?
A: Accidental removal of the warranty sticker will void your warranty. Contact customer support for assistance. -
Q: Is it safe to open the PSU casing for maintenance?
A: No, opening the PSU casing is dangerous as it contains hazardous voltages. There are no user-serviceable parts inside.
Before installation :
- Make sure that the wattage and output of your PSU are enough to power your system’s requirements.
- Make sure that the power cord is disconnected and that the PSU switch is turned off.
- This PSU was designed for NON-INDUSTRIAL desktop systems according to INTEL’s Desktop Platform Form Factors. Usage outside of these parameters, including cryptocurrency mining, might cause overheating, malfunction, or damage to your equipment and will void your warranty.
- DO NOT attempt to expand the connectors through adapters or other means.
- DO NOT operate in wet or damp conditions.
- Do NOT open the PSU casing, the unit operates with hazardous voltages, and there is no serviceable component inside.
- Do NOT remove the warranty sticker. Damage or removal of the sticker will void your warranty.
- Please visit Aerocool official website www.aerocool.io for details on your PSU warranty policy.
How to Install
-
Before installing the PSU, unplug the AC power cord and make sure the I/O panel is off. I/O panel is off
-
Connect 20+4-pin connector to the motherboard.
[Note] The detachable 4-pin connector of the 20+4-pin is not suitable for ATX12V 4-pin connector. Incorrect connection may cause irreversible damage.
Motherboard 20+4PIN -
Connect ATX12V (CPU power) 4-pin or 8-pin (by 4+4-pin) to the motherboard.
-
Connect SATA connector to devices, i.e. HDD/SSD/ODD.
-
Connect Molex 4-pin connector to devices, i.e. HDD/ODD/case fan.
-
Connect PCIe 6-pin or 8-pin (by 6+2-pin) to graphics card.
[Note] Do not connect the PCIe 6+2-pin connector to the ATX12V 8-pin
connector.
Incorrect connection may cause irreversible damage.
Please read the “PSU GUIDE” on the website via QR code before installing the
graphics card.
PCIe 6-PIN
PCIe 8-pin (by 6+2-PIN)
Connector Description
Motherboard 20+4PIN
PCIe 6+2PIN
ATX12V 4+4PIN
PATA
SATA
12VHPWR (For ATX3.0 / PCle5.0 models)
Addressable RGB
Troubleshooting
If your system does not function, please go through the steps below:
- Switch PSU main I/O to “O”(Off) to reset power supply for at least 5 minutes then follow through steps below.
- Ensure the AC cord is properly plugged into the wall outlet and the PSU.
- Ensure each DC connector is tightly connected with motherboard, graphics card and all peripherals.
- Ensure all pins are correctly plugged into the corresponding connector, for example PCIe 6+2pin is for graphics card, not CPU power socket.
- Turn main I/O switch to the “I” (On) position.