baridi DH1 Series Electric Glass Panel Heater Instruction Manual

: June 16, 2024
: baridi

Table of Contents

baridi DH1 Series Electric Glass Panel Heater
Product Information
Product Usage Instructions
FAQs
Important Information
Specification
Safety Instructions
Assembly
Operation
Maintenance
WiFi Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

baridi DH1 Series Electric Glass Panel Heater

Product Information

Specifications
- Model No.s: DH135, DH136, DH137, DH138, DH139, DH140
- Product Width: 52cm (DH135/DH136), 65cm (DH137/DH138), 78cm (DH139/DH140)
- Colour: Black/White
- Control Style: Touch Screen, Digital, or Remote Control
- Heating Technology: Convection
- IP Rating: IP24
- Material: Glass
- Mounting Location: Floor or Wall
- Number of Heat Settings: 3
- Product Dimensions (WxDxH): 52 x 12 x 47cm (DH135/DH136), 65 x 12 x 47cm (DH137/DH138), 78 x 12 x 47cm (DH139/DH140)
- Rated Power: 1000W (DH135/DH136), 1500W (DH137/DH138), 2000W (DH139/DH140)
- Supply: 230V 50Hz
- Cable Length: 1.5m

Product Usage Instructions

Safety Instructions
- WARNING! The warnings, cautions, and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product but must be applied by the operator.
ELECTRICAL SAFETY
- WARNING! It is the user’s responsibility to check all electrical equipment and appliances to ensure they are safe before using. Inspect power supply leads, plugs, and all electrical connections for wear and damage.
Important Information
- Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care for the purpose for which it is intended.
- Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.

FAQs

Q: Can the heater be used outdoors?
- A: No, the heater is designed for indoor use only.
Q: What should I do if the heater surface gets hot?
- A: Exercise caution and avoid touching the hot surface. Ensure proper ventilation around the heater.
Q: How do I control the heater settings?
- A: You can control the settings using the touch screen, digital interface, or remote control provided with the heater.

Important Information

Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.

Specification

Attribute	DH135 / DH136	DH137 / DH138	DH139 / DH140
Actual Product Width	52cm	65cm	12cm
Colour:	Black / White	Black / White	Black / White
Control Style:	Touch Screen, Digital or

Remote Control

| Touch Screen, Digital or

Remote Control

| Touch Screen, Digital or

Remote Control

Safety Instructions

WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product but must be applied by the operator.
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical connections for wear and damage. Sealey recommends that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey stockist.
If the heater is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.

ELECTRICAL SAFETY

WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before use. Inspect power supply leads, plugs and all electrical connections for wear and damage. Sealey recommends that an RCD (Residual Current Device) is used with all electrical products.
Electrical safety information. The following information must be read and understood:
Ensure that the insulation on all cables and the appliance is safe before connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a qualified electrician.
If the cable or plug is damaged during use, switch off the electricity supply and remove it from use.
Ensure that repairs are carried out by a qualified electrician.

GENERAL SAFETY

WARNING! Disconnect the heater from the main power supply before carrying out any servicing or maintenance.
Disconnect the heater from the power supply before handling or cleaning.
Maintain the heater in good order and clean condition for the best and safest performance.
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Ensure there is adequate lighting and keep the immediate area in front of the outlet grille clear.
Only use the heater standing on its feet in the upright position.
DO NOT allow any untrained persons to use the heater. Ensure they are familiar with the controls and hazards of the heater.
DO NOT let power lead hang over an edge (i.e. table), touch a hot surface, lie in the heater’s hot air flow, or run under a carpet.
DO NOT touch the outlet grille (top) of the heater during and immediately after use as it will be hot.
DO NOT place the heater near items that may be damaged by heat.
DO NOT place the heater too close to yourself or any object, allow the air to circulate freely.
DO NOT use the heater for any purpose other than for which it is designed.
DO NOT use the heater on very deep pile carpets.
DO NOT use the heater outdoors. These heaters are designed for indoor use only.
DO NOT use the heater if the power cord, plug or the heater is damaged, or if the heater has become wet.
DO NOT use in the bathroom, shower room, or in any wet environments or where there is high condensation.
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT allow the heater to get wet as this may result in an electric shock and personal injury.
DO NOT insert or allow objects to enter any openings of the heater as this may cause an electric shock, fire or damage to the heater.
DO NOT use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat-sensitive materials may be stored.
DO NOT place the heater immediately below any electrical outlet.
DO NOT cover the heater when in use, and do not obstruct the air inlet and outlet grille (i.e. clothing, curtain, furniture, bedding etc).
Allow the unit to cool before storage. When not in use, disconnect from the mains power supply and store in a safe, cool, dry, childproof area.
NOTE: Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

Assembly

Floor mounting

Invert the unit and place the top edge carefully on a soft cloth or carpet.
Fix the feet to the bottom edge using the supplied screws (2 per foot) ensuring a sound and stable fit.

Wall mounting (fig.1, fig.2)

NOTE: The installation MUST be at least 15cm off the ground and no less than 50cm away from the ceiling.
- Fig.1 – Using the correct measurements of the fixings for your particular unit e.g. 1000W, 1500W, 2000W, drill 6 holes to suit.
NOTE: Before drilling ensure that there are no hidden pipes or wires that will be damaged by the drilling.
- Fig. 2 – Fit two brackets (supplied) to the underside of the unit using the supplied self-tapping screws (2 per bracket) as shown. These will hold the unit off of the wall when hanging.

Operation

Comfort Mode: The heater is working on full power.
Eco Mode: The heater is working on half power.
Anti Frost Mode: The heater turns on if the ambient temperature drops below 6oC. Turns off when the temperature rises to 7oC.
Mode Value Selector: Cycle through options to set values.
Cycle through modes and increase values set.
Cycle through modes and decrease values set.
On / Off selection.
Control Panel Lock. Press and hold the UP arrow to engage and press and hold the UP arrow to disengage.
Heating Icon: Shows when a panel is heating.
Wireless Icon: Shows when connected.
The “h” Icon: indicates the timer has been set.
When first powered up the heater will beep, be in standby mode, and display the wireless symbol (if connected) and current room temperature.
The first time the unit is switched on the Heating and ECO icons will illuminate. This means the device is in the ECO heating mode state. The heater has a memory function, when you turn on it subsequently, it will be in the last working state and the display will illustrate this.
To change the heating mode, press the UP and DOWN buttons to cycle through the modes: ECO mode, Comfort mode and Anti-frost mode.
To adjust the set temperature of any of the modes press the Mode Value Selector button and the LED displayed value will flash then use the UP and DOWN buttons to adjust the temperature. The temperature range is from 5°C –50°C.
NOTE: the temperature cannot be adjusted in anti-frost mode.
To set the timer, press the Mode Value Selector button. When the LED displayed value flashes, use the UP and DOWN buttons to adjust the time. The timer range is 1 – 24 hours. The digits will flash while setting and then the screen will return to heating mode. The timer icon on the screen will show that the timer has been set. The heater will heat until the set time has elapsed.
To set the child lock, press and hold the UP button. The Control Panel Lock icon will appear on the screen and the control panel will be locked out. To release, press and hold the UP button. The padlock icon will disappear, indicating that all the buttons can be used again.
To turn off the LED display, press and hold the DOWN Value Selector button. Press any key to re-light the display screen.

Maintenance

Always disconnect the appliance and let it completely cool before any maintenance. Use a vacuum cleaner to remove dust on grilles. Clean the outside of the unit with a damp cloth and then dry it with a dry cloth.
Never immerse the unit in water, nor let water drip into the unit.
Always disconnect the appliance, let it completely cool and clean it before storing it. If you do not use the device for a long period, return the unit and the instruction manual to the original carton and store in a dry and ventilated place.
DO NOT place any heavy items on top of the carton during storage as this may damage the appliance.

WiFi Installation

To connect your heater to the WiFi, the first step is to download the Smart Life app onto your smartphone or tablet. You can find the app by searching “Smart Life” in the Google Play or Apple app store.
Download and install the app. Unless you already have a Smart Life account, you will need to create an account by tapping Register.
The device will automatically determine your country, although you can change this if necessary. Enter your phone number or email address. If you enter a phone number, a verification number will be sent to your phone: enter this number to verify, then create a password. If you enter your email address, you’ll just need to create a password.
To add your heater to the app, first put the heater in WiFi connection mode. The heater is in WiFi connection mode when the WiFi icon is flashing. If the wifi icon is not flashing, go to standby mode and hold down the button for three seconds.
Once the WiFi icon is flashing, go to the app and press Add a Device. Select the device type (Small Appliances > Heater) and confirm that the indicator is flashing. You will then be prompted to enter your WiFi password. This allows the app to find your heater using your WiFi.
The app will then display its connecting screen.
NOTE: if the heater is failing to connect, press and Hold the button for three further seconds. It will then switch to its secondary connection mode. The heater has two connection modes: one where the WiFi icon flashes slowly (once per second) and one where the WiFi icon flashes fast (three times per second). Most devices will connect on the fast flashing mode.
The heater will beep and display a solid WiFi icon when the device is connected.
The app will confirm that the heater has been added. You can now name the device, share it with family members, or proceed to schedule your heating.

App Operation

You can use the app to control multiple devices. The status of your devices is shown on the device list:
- Offline (device is turned off at wall/rocker switch).
- Turned Off (device is in standby mode).
- Turned On (the device is in heating mode).
When the heater is online, tap the device name to go to the control interface. NOTE: when the heater is offline, you will not be able to control it with the app.
You can change the heater’s current mode by tapping the mode buttons. You can adjust the mode’s temperature using the + and – buttons when you’re in that mode.

Scheduling Heating

You can program your heating by creating a schedule of “events”, where the heater switches on or off. These events can be temporary, like setting a timer, or they can be recurring, so the heater switches on at the same time every week.
You can set an unlimited number of events, switching the heater on and off across the week.
For every event, you must set a start time. Then, choose whether you want it to repeat. Select “Only Once” if you just want to set a timer for now. If you want the event to repeat, select which days you want it to occur. Finally, choose whether you want the heater to switch on or off. Make sure you confirm your settings at every stage and press save to keep the event.
Each event will appear in your schedule. You can activate and de-activate events using the toggle. You can also delete events by swiping left and tapping Delete.
The heater will beep when it begins a new heating event. The heater will heat at whatever mode it was last set to: you cannot schedule mode changes. NOTE: if you change the heater’s setting during an event – i.e. turning it on when it is scheduled to be off – the heater will remain as it is until the next scheduled event.

Smart Features

The “Smart” section of the SmartLife app allows you to add functions that make your heating easier and more intuitive to control. The Smart section can be reached by pressing the Smart icon at the bottom of the app.
Scenarios: Scenarios are customisable commands that bring all your devices together to perform set actions. They appear as shortcuts on the app which you can trigger by tapping the image, offering a quick and easy means of co-ordinating your heating. For example, you could create a “Heat Boost” scenario that, at one tap, switches all your panel heaters on, at high power mode, at 30 °C.
To create new scenarios, press the + button while on the Scenario screen. You can add as many heaters as you want to a scenario. You can control whether they switch on or switch off, what mode they run on, and what temperature they are set to. Any device controlled by the SmartLife app can be added to a scenario.
Automation: Automation allows you to set up actions that are triggered by external events. Triggers include the weather, temperature, humidity, sunset, sunrise and your location. You can add multiple actions and multiple triggers for each automation event, so you could, for example, set all your heaters to come on at 21°C if you arrive home when it’s snowing! To create new scenarios, press the button while on the Scenario screen.

Voice Integration:

Smart Life is compatible with both Amazon Alexa and Google Home.
To connect, first download the SmartLife skill onto your Alexa or Google Home app.
You can then link your Alexa or Google Home app with your SmartLife app. Depending on your device, your voice control app may discover your device automatically, or you may need to prompt it to do so.
Once the SmartLife skill is enabled and linked with your SmartLife app, you should get notifications whenever you add a new heater or scenario. The notification will tell you what to say to control the heater or scenario by voice.
You can find quick guides and FAQs for connecting the app to both Google Home and Alexa in the FAQ section. Press then
Sharing: You can share control of your devices with family members. Go to the Family Management then Add Member.
Add your new family member’s email address or phone number to send an invitation.
NOTE: you can only share numbers and email addresses that are connected to app-compatible devices: smartphones or tablets.
When you add new members you can choose whether or not to set them as an administrator. Members added as administrators will have all family permissions, including the facility to delete the family.
Members not set to administrator can control scenarios and devices but cannot add or remove them.

Environment Protection and Waste Protection and Electrical Equipment Regulations (WEEE)

Recycle unwanted packaging materials. When this product is no longer required or has reached the end of its useful life, please dispose of it in an environmentally friendly way.
Drain any fluids (if applicable) into approved containers, in accordance with local waste regulations.
Under the Waste Batteries and Accumulators Regulations 2009, Dellonda would like to inform the user that this product contains one or more batteries.
It is our policy to continually improve products and we reserve the right to alter data, specifications and parts without prior notice.
No liability is accepted for incorrect use of this product. Guarantee is 12 months from purchase date, proof of which is required for any claim.

Product Information Sheet. Local Space Heaters, Electric.

SUPPLIER_NAME_OR_TRADEMARK
Dellonda EU Ltd.
DELEGATED_ACT
2015/1188/EU
MODEL_IDENTIFIER
DH138

Electric Glass Panel Heater, 1500W, Wi-Fi Enabled, White

ADDRESS Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland
PHONE_NUMBER 01284 757 500
EMAIL_ADDRESS TechnicalCompliance@dellonda.co.uk.

Suppliers websitehttps://www.dellonda.co.uk/.

www.dellonda.co.uk.
DH Panel Heaters
Issue: 3 26/01/24
Model No.s: DH135, DH136, DH137, DH138, DH139, DH140

Thank you for purchasing a Dellonda product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.