BROBO GROUP SA350 Semi Automatic Saw User Manual

BROBO GROUP SA350 Semi Automatic Saw

Specifications

• Product Name: Semi-Automatic Saw Model SA350, SA400
• Manufacturer: Brobo Group (Aust) Pty. Ltd.
• Address: 8 Fowler Rd, Dandenong South Victoria 3175, Australia
• Contact: +61 3 9794 8751
• Email: info@brobo.com.au
• Website: www.brobo.com.au

Product Usage Instructions

Chapter 1: Installation of the Machine

1.1 Unpacking & Handling the Machine

Ensure careful handling during unpacking to prevent damage.

1.2 Parts Checklist

Refer to the parts checklist provided to ensure all components are present.

1.3 Minimum Requirements

Review the minimum space and power requirements for installation.

1.4 Anchoring the Saw

Securely anchor the saw to ensure stability during operation.

1.5 Connection to Power Source

Connect the saw to a suitable power source following safety guidelines.

1.6 Connection to Compressed Air Supply

If applicable, connect the saw to a compressed air supply as per instructions.

Chapter 2: Safety & Accident Prevention

2.1 Operation of the Machine

Follow safety guidelines regarding noise levels, power supply, and compressed air supply.

2.2 General Requirements

Understand and adhere to general safety requirements for operating the machine.

2.3 Advice for the Operator

Provide operators with necessary advice and training for safe operation.

2.4 Machine Safety Devices

Familiarize yourself with safety devices and reference standards for the machine.

Chapter 3: Main Functions & Operation of the Machine

Detailed information on cutting head, saw safety guard, saw actuator, vice clamp, and PLC control.

Chapter 4: Drawings, Layouts, Assembly & Spare Parts

Refer to drawings and assembly instructions for maintenance and part replacement.

Chapter 6: Maintenance & Selection of Consumables

Learn about operator roles, maintenance requirements, and selection of consumables.

Chapter 7: Troubleshoot

Refer to troubleshooting guides for blade and cutting problems.

FAQs

• Q: Can I use blades other than the standard sizes mentioned?
  • A: The provided blade selection chart offers guidance on alternative sizes. However, ensure compatibility for optimal performance.
• Q: How do I handle machine breakages?
  • A: Follow the troubleshooting guide in Chapter 7 or contact Brobo Group Pty. Ltd. for assistance.
• Q: What if I encounter unsatisfactory cutting performance?
  • A: Check the blade selection and machine setup according to the manual. Contact Brobo Group Pty. Ltd. for further support.

©

A.C.N. 098 264 316

A.B.N. 42 098 264 316

BROBO GROUP (AUST) PTY. LTD. 8 Fowler Rd, Dandenong South Victoria 3175, AUSTRALIA.

+ 61 3 9794 8751

info@brobo.com.au

+ 61 3 9794 8792

www.brobo.com.au

PRODUCT & MAINTENANCE MANUAL
SEMI-AUTOMATIC SAW MODEL No. SA350, SA400

YOUR BROBO DISTRIBUTOR IS:

Precision Drilling Machines Tapping Machines Multi-Head Drills Tool Grinders Tool Post Grinders Machine Vices Special Production Equipment
Accessories Riveting Machines Pedestal Grinders Metal Cutting Saws Linishers

Bro b o G ro up brobo.com.au

TECHNICAL SPECIFICATION

STANDARD BLADE SIZES

Outer Diameter ( mm)

Thickness (mm)

315

2.5

350 ()

2.5

400

3.0

TABLE 1. Standard Blade Sizes

BLADE SELECTION CHART

Bore Size (mm)
40 40 40

Number of Teeth
160 180 220
() Recommendation

HOLLOW CROSS-SECTION

Material Outer Diameter ( mm)
20 40
50
80
100
120

Wall Thickness (mm)
1 2 3 1 2 3 4 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5

10

20

SOLID SECTIONS

30 40

50

60

TABLE 2. Blade Selection Chart

Blade Diameter ( mm) & Number of Teeth

315

350

400

320

350

400

240

280

340

180

220

240

320

250

400

220

260

280

160

180

200

140

160

180

320

350

400

220

280

300

180

200

220

160

180

200

140

160

180

300

320

360

200

220

240

200

200

220

160

180

180

140

160

180

300

300

340

220

200

220

200

180

180

160

140

160

140

120

140

300

340

200

220

180

180

160

160

120

140

280

280

300

160

200

240

140

160

200

120

140

140

80

100

120

80

100

NOTE – CHART GUIDE ONLY This chart is issued as a guide only. Many other factors would attribute to the cutting performance of both the saw blade and the cutting saw machine. BROBO GROUP Pty. Ltd. will not accept any responsibility for the blade selection and/or machine breakages or unsatisfactory cutting performance of both the blade and/or the machine as a direct result of the selection.
Bro b o G ro up brobo.com.au

Blade Type: Drive Pin Holes (Qty. PCD):

High-Speed Steel (HSS) 180 Tooth Blade ( 350mm x 40mm bore)

SA350 SA400

2 8mm 55mm 2 10.5mm 64mm

MOTOR SPECIFICATIONS
1. CMG Motor 3 Phase/ 4 Poles/ IP55 /100L
V220-240 /50Hz/2.2 kW/1455 rpm V380-415 /50Hz/2.2 kW/1455 rpm V440-480 /60Hz/2.5 kW/1745 rpm
2. WEG Motor 3 Phase /4 Poles/ IP55 /100L
V220-380 /50Hz/2.2 kW/1420 rpm V230-400 /50Hz/2.2 kW/1425 rpm V240-415 /50Hz/2.2 kW/1430 rpm V460/60Hz/2.5 kW/1735 rpm

Worm Gear Drive Ratio
Sound Level (dBA): Spindle Speed:
VICE CLAMPS
Clamping Range (mm) Air Requirements: Air Consumption (L): Clamp Working Pressure (kPa): Maximum Pressure (kPa): Pneumatic Stroke (mm): Clamping Force (N):
TABLE 3. Vice Clamp

1:33 Reduction No of Starts (Shaft) : No. Teeth (Wormwheel)
85 – 90 dB (A) Maximum Dual Speed Selection (21/42 RPM)
Pneumatic Vice
0 – 135 (145mm w/o wear plates) Dry, filtered, lubricated air supply 1/6 Litre per cycle per vice-cylinder
600kPa (6 Bar = 87psi) 1000kPa (10 Bar = 145 psi)
10mm 1620 N / 1 Bar air pressure (365 lb force). At 600 kPa, Clamping force = 9720 N = 991 kg force = 2185 lb force

Bro b o G ro up brobo.com.au

CUTTING RANGE

CrossSectional Angle
Profile

Cutting Range (mm)

SA350

SA400

90

115

4 4/8″

130

5 1/8″

45

110

4 3/8″

120

4 6/8″

90

100 100

3 7/8″ 3 7/8″

110 110

4 3/8″ 4 3/8″

45

85 85

3 3/8″ 3 3/8″

95 95

3 6/8″ 3 6/8″

90

85 135

3 3/8″ 5 3/8″

100 135

3 7/8″ 5 3/8″

45

85 95

TABLE 4. Cutting Range

3 3/8″ 3 6/8″

100 95

3 7/8″ 3 6/8″

Note: The above values are based on a full-size blade. The capacities will reduce accordingly when a worn blade is resharpened.

DIMENSIONAL SPECIFICATIONS

Base Dimensions (L W):

550mm 660mm

Table Working Height:

968 mm

Saw Height:

1480 mm

SAW WEIGHT Packaged SA350 SA400

278 kg 280 kg

Brobo Group brobo.com.au

CHAPTER 1 –

Installation of the Machine

1.1. Unpacking & Handling the Machine
WARNING ­ HEAD HEAVY MACHINES The metal sawing machines are heaviest where the saw heads are fitted & as such, care must be taken while relocating or moving the machines. Upon receiving the Brobo Group SA350/SA400 Semi-Automatic Saw, the machine should be standing upright & positioned centrally on top of a wooden pallet. While the machine is situated on the pallet, position the forklift arms under the pallet between the runners, keeping in mind that the machine is head heavy. Move the entire unit to an accessible area as close as possible to the final location. Carefully remove the wooden frame surrounding the saw unit (Figure 1). Once completed, proceed by elevating the machine away from the pallet base using a sling harness wrapped around the cutting head of the saw. Ensure that the floor is as level as possible before finally positioning the machine to the desired location.
FIGURE 1. Handling of Semi-Automatic Cutting Saw Unit
PLEASE OBSERVE & FOLLOW THE INSTALLATION INSTRUCTIONS ON PAGE 7
Brobo Group brobo.com.au

1.2. Parts Checklist

Along with the saw unit, check that the following accessories, packed “loose”, are included as follows:

A.

STANDARD ACCESSORIES

1. 1 Saw Blade 2) 1 Operating Handle 3) 1 Service Kit (Hexagon wrenches 10mm & 14mm) 4) 1 Operating Manual

B.

OPTIONAL ACCESSORIES

Part Number 9311270 9501450 9501470 9501210
9501740 9301450 9501640
–

Description Standard Adjustable Length Stop (600mm) `Brobo-Rule’ Series Manual Micro-Adjustment Length Stop
Available in 3.0m or 6.0m lengths
Field Kit includes rail, tape, micro-stop & extension arm.
Roller Conveyor
68 Kg Steel Rollers
3000mm x 305mm
150mm pitch
Fabricated Sheet Metal Stand Floor Stand, Angle Iron Brobolube Additional Blade(s) – Custom to Client Requirements

1.3. Minimum Requirements
For the machine to function correctly, the room in which the saw unit is to be installed must be in the vicinity of, & satisfy the following conditions:
240/415V Power Supply Working Pressure – Not less than 600kPa (6 Bar) & no greater than 900kPa (9 Bar) Ambient Temperature – From -10C to +50C. Relative Humidity: Not more than 90%. Lighting: More than 500 LUX.

WARNING ­ OPERATING VOLTAGE VARIATION
Each saw model has an inbuilt safety system to protect it against voltage variations. However, for the machine to perform efficiently, ensure that the saw unit operates within 10% limits of the recommended voltage of the motor.

Bro b o G ro up brobo.com.au

1.4. Anchoring the Saw
Prior to anchoring the saw unit, take into considerations the requirements mentioned in Section 1.3 & Section 2.2, & other aspects regarding the usage of the machine such as accessibility to cut parts & safe access for the operator. The base of the fabricated stand (if applicable), in which the saw head rests on, is anchored to the floor by 4 M12 bolts provided. For added stability, it is strongly recommended that the machine stand is fastened to the floor by using loxins (not provided). When positioning & fastening the unit, please refer to the hole locations shown in Figure 2.

Figure 2. Anchoring Hole Locations

Bro b o G ro up brobo.com.au

1.5. Connection to Power Source
Before connecting the machine to the power supply, check that the socket is not connected in series with other machines. This condition is critical for the ideal operation of the saw unit.

Single & Three Phase

a) Single phase machines are provided with three pins, 15 amps rated plugs & leads for connection to 240V, 50Hz power supply in Australia.[AS/NZS 3000:2018]

Active = Brown Neutral = Light Blue
Earth = Green/Yellow

VOLTAGE 240V/1 PH

MAIN VOLTAGE 240V

Figure 3.1 Connection 3 pins ­ 1 Phase

b) Three phase machines should be fitted with a suitable, approved 5 pin plugs (Australia)

5 Core Cable Phase/Line 1 Brown

Phase/Line 2 White

Phase/Line 3 Red

Neutral

Light Blue

Earth

Green/Yellow

5 Pin Plug Male 415 V/AC/3PH/50Hz

5 Pin Socket Female 415 V/AC/3PH/50Hz

Figure 3.2 Connection for “5-CORE” Wire System with Neutral ­ 3 Phase
c) Check the power supplied & motor specifications before plugging in the machine. Check the terminal connection on dual voltage motor terminal box & connect it accordingly to the corresponding voltage supply.
d) If the dual motor is requested, the motor is always connected to the higher voltage, unless otherwise specified prior to the order being placed.
Bro b o G ro up brobo.com.au

To connect the machine to the power supply, proceed as follows:

1. Insert the power plug into the socket, while ensuring that the mains voltage is compatible for which the saw unit is operating.
2. Switch the saw on by rotating the control switch located on power switch assembly as shown in Figure 4 below.

Figure 4. Main Control Switch
3) Make sure that the saw is NOT currently in an emergency condition, whereby the EMERGENCY STOP button is depressed. If so, twist the red mushroom button until it is released & returned to the neutral state.
4) On first power-up, ensure that pneumatic vice is operating in a correct direction acting to release the piece when the saw is not running & clamp what saw is running.
5) Check that the motor is operating in the correct direction, that is the blade is rotating downwards & into the direction of the vice clamps.
6) Ensure that all electrical leads & cables (including supply leads) are maintained in good condition & away from sharp objects. All leads should be replaced if cut, sliced or damaged in any way.
1.6. Connection to Compress Air Supply
To ensure the ideal operation & long service life, it is recommended that the semi-auto saw is connected to a compressed air system with similar characteristics shown in Figure 5 below.

Figure 5. Ideal Air Supply Connection
Brobo Group SA350/400 Semi-Automatic Saw is now ready for use. Chapter 3 provides a detailed description of the various features of the saw & its operating cycles

Bro b o G ro up brobo.com.au

CHAPTER 2 –

Safety & Accident Prevention

The Brobo Group SA350/400 Semi-Automatic Saw has been designed & manufactured in accordance with Australian Standards. It is HIGHLY RECOMMENDED that the instructions & warnings contained in this chapter be carefully followed for correct usage of the machine.
2.1. Operation of the Machine
The Brobo Group SA350/400 Semi-Automatic Saw is specifically designed to cut ferrous & non-ferrous metal cross sections with solid or thin-walled profiles. Other types of material & machining are not compatible for use with the specifications of the saw. This machine involves a high-speed blade rotation; therefore extreme caution is required when operating the device.
The employer is responsible for instructing the personnel who, in turn, is obliged to inform the operator of any accident risks, safety devices, noise emission & accident prevention regulations provided for by national & international laws governing the use of the machine. The operator must be fully aware of the position & functions of all the machine’s controls.
All those concerned must strictly adhere to ALL instructions, warnings & accident prevention standards in this manual.
The following definitions are those provided for by the EEC DIRECTIVE ON MACHINERY No. 98/37/CE:
Danger Zone – any zone in and/or around a machine in which the presence of a person constitutes a risk to the safety & health of that person.
Person Exposed – any person finding him or herself, either completely or partly in a danger zone.
Operator – the person or persons are given the responsibility of installing, operating, adjusting, maintaining, cleaning, repairing, & transporting the machine.
WARNING ­ UNAUTHORISED MODIFICATIONS/REPLACEMENTS/USE The manufacturer declines any responsibility whatsoever, either civil of criminal, in the case of unauthorised interference or replacement of one or more parts or assemblies on the machine, or if accessories, tools & consumable materials used are different from those recommended by the manufacturer, or if the machine is inserted in a plant system & its proper function is altered.
2.1.1. Noise Level
The noise level of an idling metal saw, fitted with a 180-tooth blade (supplied as standard by Brobo Group) has been measured to be below 85 dBA. This complies with the Australian Occupational Health and Safety (Noise) Regulations 1992.
Please note that peak impulse noise levels will be experienced due to variables including blade characteristics, type, & condition. This will also vary accordingly depending on the size & type of sample being cut. Under these circumstances, management should make available to the operator(s) the appropriate hearing protection equipment as prescribed under the above-stated act.
Bro b o G ro up brobo.com.au

2.1.2. Power Supply
The 240/415V power supply requirements for this machine are of a high level & unauthorized interference & or inadequate maintenance could result in a situation that could put the operator at risk. A qualified electrical engineer should always be assigned to maintain & repair the system.
2.1.3. Compressed Air Supply
Various functions of the saw are carried out via the use of 6 bar compressed air. During these operations, situations would arise where machine parts & materials are clamped together & would potentially pose a serious safety issue to an inexperienced operator. Operators should be thoroughly instructed about these hazards. Only a qualified electrician should carry out regular maintenance of this system.
2.2. General Requirements
Lighting Insufficient lighting during the operation of the saw unit would constitute a safety hazard for the people concerned. For this reason, the user of the machine must provide adequate lighting in the working area to eliminate areas of shadow, whilst also preventing dazzling illumination sources (Reference standard ISO 8995 – 2002 `Lighting of Indoor Workplaces’).
Connection Check that the power supply cables, compressed air supply (if applicable) & coolant system complies with, & are operating within the acceptable range of the saw capabilities. Faulty, damaged or worn components must be replaced immediately.
Earthing Systems The installation of the earthing system must comply with the requirements stated in the: IEC Standards Part 195: Earthing & Protection Against Electric Shocks 1998.
The position of the Operator The user controlling the machine saw operations must be positioned as shown in figure 6 below.

Figure 6. Correct Position for Operating Saw Unit

Brobo Group brobo.com.au

2.3. Advice for the Operator
Protective eyewear or goggles must be worn at all times while attending & operating the metal saw.
Do not attempt to operate the machine unless all safety guards are in operation. The guard must fully cover the blade when the head is in the uppermost position.
Ensure that hands & arms are kept clear of the cutting zone when the machine is operating.
Do not wear loose clothing with long sleeves & oversized gloves, bracelets, necklaces or any other loose object that may become entangled in the machine’s blade during cutting. Long hair must be tied back or placed in a hair net. Always disconnect the power supply to the machine before carrying out any maintenance work or adjustments. This includes cases of abnormal operations of the machine.
Any maintenance work performed on the hydraulic, pneumatic or coolant systems must be carried out only after the pressure in the system has been released.
The operator MUST NOT conduct any risky operations or those not required for the cutting in course (e.g. remove swarf shavings from the machine while cutting). Never move the saw while the machine is operating.
Always keep the workplace are as clean as possible. Remove equipment, tools or any other objects from the cutting zone.
Support the workpiece on both sides of the machine to prevent it from falling or jamming during the cutting cycle.
Bro b o G ro up brobo.com.au

Ensure that the specimen being cut is secured firmly in the vice clamps & the machine has been correctly set. Figure A show some examples of how to correctly clamp different specimen profiles. Before commencing the cut, be sure the vice(s) is securely clamped & the machine set-up is correct.
Figure A. Correct Clamping of Cutting Specimens
Do not use cutting blades of different sizes to those recommended to the machine’s specifications. Always follow safe practices & inspection procedures when installing blades (Please refer to section 5.1 Changing the Blade).
When cutting very small specimens, ensure that the workpiece is not dragged behind the back fence support, where it could get lodged behind the blade.
If the blade jams during a cut, activate the emergency stop function immediately. Do not continue forcing the blade through. This could damage the blade, the specimen or be a cause for potential injury to the operator. Always turn off the machine before carrying out any repair work. Consult the Brobo Group Engineering Department in the country in which the machine was initially purchased.
Bro b o G ro up brobo.com.au

2.4. Machine Safety Devices
This product & maintenance manual is not purely intended as a guide for the usage, operation & maintenance of the saw unit in a strict production environment; it is instead an instrument to providing information on how to use the machine correctly & safely. The following standards listed in section 2.4.1, which are applicable to the Brobo Group SA350/400 Semi-Automatic Saw, are those specified by the EEC Committee that governs the safety of machinery, health & safety at work, personal protection & safeguarding of the work environment. In addition, the saw also complies with the Australian Standards regarding the safeguarding & general requirements for electrical equipment.
2.4.1. Reference Standards
MACHINE SAFETY EEC Directive No. 98/37/CE – Machines Directive EEC Directive No. 91/368 – 94/68 – Amends sections of EEC Directive No. 98/37/CE relating to machine safety EEC Directive No. 73/23 – Low Voltage Directive AS4024.1 – 1996 – Safeguarding of Machinery
HEALTH & SAFETY AT WORK AS3100 – 2002 – General Requirements for Electrical Equipment OH. & S. 1995.81/1995 – Compliance References EEC Directive No. 80/1107; 83/477; 86/188; 88/188; 88/642 – Protection of workers against risks caused by exposure to physical, chemical & biological agents in the workplace EEC Directive No. 73/23 & Special EEC Directives No. 89/654; 89/655 – Improvements in health & safety at work
Bro b o G ro up brobo.com.au

CHAPTER 3 –

Main Functions & Operation of the Machine

AW HEAD BACK FENCE

3.1.1. Cutting Head

Figure 8. Saw Main Components

As the name suggests, the cutting head is the focal area where most of the specimen cutting takes place. Thus, correct saw blade selection such as size, number of teeth & tooth pitch are all critical factors that determine the overall performance & quality of the final cuts. In addition, the use of correct saw blade provides minimum burr to the workpiece while maximizing the safety to the operator during each cutting procedure.

3.1.2. Saw Safety Guard
The primary purpose of the saw safety guard (Figure 9) is to protect the user from the spinning blade. It also functions as a safety device to protect the operator from any broken tooth, swarf or highvelocity particles that might be dislodged by the cutting process.

Figure 9. Saw Safety Guard

Bro b o G ro up brobo.com.au

3.1.3. Saw Actuator
The actuation unit (Figure 10) is a lead screw electric linear drive with special functions purpose-developed for cold cutting:
Auto cut-piece size detection & setting of saw stroke Constant force cutting Active Overload Feed Control

3.1.4. Pneumatic Vice Clamp
Operating at 600kPa, the vice clamps (Figure 11) firmly secure the workpiece in preparation for cutting. The pressure of each vice clamp could be modified using the pressure regulators located on the main electrical unit door. Each vice must be adjusted manually to accommodate various cross-sectional profiles.

Figure 10. Actuator

Figure 11. Pneumatic Vice Clamp
Bro b o G ro up brobo.com.au

3.1.5. PLC ENCLOSURE

Figure 12. PLC Control Box
Cutting Speed Selection The Brobo Group SA350/400 Semi-Automatic Saw comes with fully adjustable RPM & saw feeding speed. RPM is adjusted on the Spindle RPM radio button. Feeding speed is adjusted at the Feed Rate radio button (Figure 12). The actuation unit feeds at constant force hence the cutting speed will vary also according to the thickness of the cut section. The recommended cutting RPM for Mild Steel is 40 to 60 RPM, for galvanized & stainless steels the recommended cutting speed is 20 to 25 RPM.
Dual Start Button The primary purpose of the dual start buttons is to prevent the user from accidentally activating the machine. Assuming that the power is connected to the machine, both buttons must be depressed simultaneously before the cutting cycle will activate.
End Cut Detect Button The SA350/400 Saw completes a cut using an auto-detect system for determining when it has cut through the piece. This ensures that the saw completes the cut in the fastest possible time. This system works reliably on all RHS & round sections, however, for some profile sections, it will fail to detect the end of the cut & finish cutting too early. The operator can turn this on/off using the END CUT DETECT button. When switched off the saw makes the deepest possible cut

It is also possible to limit the cut depth while END CUT DETECT is on by unscrewing the depth adjustment screw while tightening the screw increases the cut depth. (Figure 13)

Emergency Stop Press the Emergency Stop Button during any operation to

immediately stop the saw.

The saw must be recalibrated after the emergency stop.

Figure 13. Adjustment Screw

(Please refer to section 3.2 Preparation for Operation)

When the Emergency Stop Button has been pressed the ‘ON’ light will turn off.

Wait 5-10 seconds then release the emergency stop button.

To release the emergency stop button from the depressed position simply twist it in the clockwise direction.

WARNING – BLADE JAMMING
If the saw blade jams during a cut, engage the EMERGENCY STOP immediately. Remove the part, check that the blade is not damage and if need be, replace the blade.

Bro b o G ro up brobo.com.au

3.2. Preparation for Operation
The following procedure is recommended for the correct cutting using the Brobo Group SA350/400 Semi-Automatic Saw
WARNING ­ SAFETY GEAR Protective clothing, safety glasses and gloves should always be worn while loading parts, operating the machine, or undertaking any maintenance work on the saw.

PROCEDURE
1. Cleaning Using a non-flammable & toxic free solvent, clean the machine to remove any corrosion protective coating prior to use.
2. Power On Ensure that both the air & electric power systems are turned on, where applicable. The electrical power source must be available before any pneumatic functions will operate.

3. Calibration

Upon power-up, the saw needs to be calibrated.

Immediately upon power-up pushing the STOP/RESET button will calibrate

the saw. (Figure 14)

The saw will not respond to any other buttons until it is calibrated.

The saw calibrates by seeking both forward & back. The saw will first seek

back, then forward, & MUST home forward against its base

Ensure there are no bars placed across the cutting area.

Once the saw touches the base it will go to the home position, briefly run the blade & wait for the

next command.

Figure 14. Stop/Reset Button (Calibration)

WA RNING – BLA DE C HA NG E
Calibration of the saw must be done after every blade change. Not doing so may result in the blade cutting into the base of the saw or actuator jamming. Ensure that the saw is turned off during blade changes.

4. Angle Adjustment To adjust the angle of the cutting surface, if necessary, loosen the 2 bolts (Figure 15.) Fine-tune the angle required, then replace & retighten the 2 bolts.

5. Vice Clamp Setting
Place the cutting specimen you wish to cut into the vice clamps. With a pneumatic vice, manually adjust the clamps so that the jaws are clamped firmly to the workpiece or with a clearance of 3 – 7mm. (Figure 16) (For correct clamping of material, please refer to section 2.3 Advice for the Operator).

Figure 15. Adjustment

Position the vice clamps & component as close to the blade as possible without interfering with the travel of the blade or guard. Vice relocation is required whenever the head angle is altered.

Figure 16. Clamp Clearance 3-7mm
Bro b o G ro up brobo.com.au

6. Vice Clamp Pressure For pneumatic vices, set the vice clamping pressure from the pressure regulators located on the main control unit door. The vice clamps advance with an approximate 10mm pneumatic stroke to apply a clamping pressure of 6 bar (87 psi).
If for any reason this pressure is not available on a continuous basis, the regulator on the air service unit must be set slightly below the available line pressure, & the safety low-pressure indicator valve needs to be reset to correspond with the newly available pressure. The need to change the pressure is necessary to allow for lighter materials with hollow cross sections to be cut without deforming the walls thicknesses.
7. SET Button Once the workpiece & vices are in position press the SET button (Figure 17) Vice jaws automatically close & apply clamping pressure. The vices will clamp the piece & the saw will begin to seek the workpiece. Once the blade touches the workpiece it will rise slightly & then stop moving. At this point, the vice will release the piece. The saw is now ready to cut the workpiece.
Figure 17. Set Button

8. CUT Button

When ready to cut, press the two CUT buttons simultaneously, (Figure 18)

The vices will clamp the workpiece, the blade will being to

rotate & the saw will lower to cut the piece.

Once the cut is complete the vices will release the workpiece & the saw will

return to the position set before the cut, ready to cut the same piece again.

To continue cutting this piece, simply place more tube in vice & press two

CUT buttons simultaneously.

Figure 18. Dual Cut Button

9. STOP/RESET BUTTON
When ready to cut a different sized piece or to stop the saw during any operation, simply press the STOP/RESET button. (Figure 19)
The saw will stop the current task immediately & return to the home position.

Figure 19. Stop/Reset Button
WA RNING – BLA DE MO TO R O VERLO A D
Saw is equipped with overload monitoring system which detects main motor overload in case of blade jam or inadvertent misuse. In case of overload saw reverses feed, re-establishes correct running of motor & continues the cut. If the saw overload system is reversing feed regularly during a cut, it indicates the blade is worn. Replace the blade promptly at this occurrence changes.

Bro b o G ro up brobo.com.au

3.3. Operation Recommendations
Select the correct saw blade with the correct tooth pitch & form to suit the material to be cut to provide minimum burr & maximum blade lifespan. o SA350 Blade Sizes 320-350 mm o SA400 Blade Sizes 350-400 mm
Use the smallest diameter blade & coarsest pitch that is practical within the required speed & material limitations.
Generally, use a tooth pitch to give 2 – 4 teeth engagement with the material during cutting. Ensure that sufficient coolant is flowing over the cutting teeth. Do not allow the machine’s gearbox to run idle in the upright position for more than 3 minutes otherwise,
damage can occur to the drive system. The rate of feed affects the quality of the final cut & blade life. This varies also by the material & cross-
sectional dimensions. When cutting stainless steel or high carbon steel (Brinell hardness above 200), the slowest speed machine should be used together with a cobalt type high-speed steel blade. As a rule of thumb the softer the component, the faster the rate of speed. Thus, it is recommended that slower speeds be used for hard & tough materials & higher speeds for soft, ductile materials. Note that for non-ferrous materials such as brass, copper, aluminium etc. require much faster speeds than provided on this machine. If these are the majority of materials cut, a Brobo NF Series machine should be considered.
CHAPTER 4 –

Drawings, Layouts, Assembly & Spare Parts

Bro b o G ro up brobo.com.au

500 1020

1800

WALL/ SAFETY SCREEN

3000

3000

660

A= 3000 OR 6000

A+ 600

MINIMUM 600 ALL AROUND SAFE

SPACE FOR OPERATING ZONE

OPERATOR ZONE

660 610
4 x 15 THRU

300 530 480

SAFE WORKING ZONE

MACHINE ZONE

1050 10

142.5 VICE CAPACITY
10

ANCHORING HOLE LOCATION

7 5 WEAR PLATE TRAM2VA7EX8L

1520

965 4 1

890 STAND
965 TABLE

135

484

9501740

660 915

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 06.10.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

548
TITLE:
BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

A
SEMI AUTO SAW MAIN DIMENSIONS

677

DO NOT SCALE DRAWING DWG NO.

SCALE:1:10

REVISION 0

001002

A3 SHEET 1 OF 1

ITEM NO. 38 39 40
41 42 43 44
45

PART NUMBER 9911540 9504350 9305150
9314690 8735160 8715210 8705140
9911570

DESCRIPTION

QTY.

Lower Link 140mm

1

Swing Bolt Hole 8mm

2

Saw Compression Spring

1

Socket Head Shoulder Screw M8x50

1

Nylon Nut Lock M8

1

Hex Lock Nut

3

Socket Head Cap Screw M8x35

1

Semi Auto Saw Link Spacer 1

43 38

41 42

44 43

40 39

45

ITEM PART NO. NUMBER

DESCRIPTION

47 9332060

Back Fence RH

1

48 9332070

Back Fence LH

1

49 8705210

Socket Head Cap Screw M10x80

2

50 8705250

Socket Head Cap Screw M12x40

4

51 8705280

Socket Head Cap Screw M12x65

2

52 8715140

Dowel Pin 12×30

2

53 9304220

Locking Pad 15.9 x 9.5 (Brass)

2

54 8705380

Flat Countersink M8x16

4

55 9514280

Wear Plate 10mm

2

48 55 54

49 51 50 52
47

28 26 25
29 27 12 15 2 5 36
11 10 14 13 9 8 7

53

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 06.10.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

16 24 19 23 20 21 18 17

ITEM NO.

PART NUMBER

DESCRIPTION

QT Y.

1

9312000

Clamping Table (Original)

1

2

8705300

Socket Head Cap Screw M12x100

2

3

8705270

Socket Head Cap Screw M12x60

2

4

9305110

Grease Nipple M8x1.25

1

5

9824010

Clamping Table Bush

2

6

9304770

Hollow Dowel

2

7

8715810

Socket Set Screw M12x16

1

8

9315000

Spring 9.5 x 1.6 x 110 L

1

9

9324180

Pin Lock 10

1

10

1065100

Brobo Name Plate

1

11

8715730

Drive Pin

2

12

BFA

3

13

9501740

Back Fence Assembly

1

Stand/Tank Assembly

1

30

14

9311110

Coolant Tank Assembly

1

15

AS-CMG

Pivot Block Assembly for Auto Saw

1

4

16

9911560

M20 Plug

1

17

9505023

6

18

9304660

Motor 2.2Kw 4 Pole

1

Spacer Ring SA 45x28x16.5

1

19

9505380

1

20

9505022

Coupling Half L100.24

1

Ring Kit

1

37

21

9505021

22

8725770

Coupling Half L100.28

1

Socket Head Cap Screw

4

23

9911410

Gearbox Cover Plate

1

24

8726100

Button Head Socket Screw M6x16

2

25

9911480

26

8705340

Gearbox Side Bracket

1

Flat Socket Head Cap Screw M6x16

4

27

9542050

Saw Outer Guard

1

28

8705440

Socket Head Shoulder Screw M10x40 1

29

9911550

Semi Auto Saw Link Assembly

1

30

9911460

Brobo Cylinder

1

31

9911020

Eureka Enclosure Assembly

1

32

9501260

SA BRACKET FOR EUR403015

1

33

8705140

Socket Head Cap Screw M8x35

4

34

8705120

Socket Head Cap Screw M8x20

4

35

8705720

Hex Nut M8

12

36
35 34 31 32 33 37

9311200 9915450

Pneumatic Vice Assembly (Heavy Duty) 2

Air Service Unit

1

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE:
SEMI AUTO SAW ASSEMBLY

DO NOT SCALE DRAWING DWG NO.

SCALE:1:10

REVISION 0

002002

A3 SHEET 1 OF 1

ITEM NO.
1 2 3 4 5
6

PART NUMBER

DESCRIPTION

QTY.

9512000 8705060 9405010 9302120 9305070

Saw Gearbox

1

Socket Head Cap Screw M6x16

8

Oil Sight Window with Flat Gasket

1

Front Cover Plate

1

Shim 50x60x0.05

1

9305020

Taper Roller Bearing 30x62x17.25 30206 1

7

9314000

8

9304430

Worm Shaft

1

Key Wormshaft 7x8x31

1

9

9305030

Taper Roller Bearing 30x72x20.75 30306 1

10

9315040

11

9312100

Oil Seal 52x30x7 (TC12495)

1

Retainer Ring

1

12

8705070

Socket Head Cap Screw M6x20

4

13

9302110

Side Cover Plate

1

14

8705420

Flat Socket Head Cap Screw M10x25

1

29

15

9304130

Retainer Washer 55×10

1

16

8705090

Socket Head Cap Screw M6x35

3

17

9315090

Sum Plug 1/2″ NPT

1

18

9405450

Coolant Pump

1

19

9324070

Pump Mounting Plate

1

20

9304017

Pin – Coolant Pump

1

21

8705560

22

9505030

Hex Head Screw M8x20

2

Nylon Hose Kit 8mm

1

23

9314050

24

9305010

25

9504080

WormWheel

1

Double Seal 90x70x10

1

Main Spindle S315.S350

1

26

9314420

Key – Main Spindle

1

27

9504090

Spindle Counter Plate (S315D, S350D)

1

28

8715080

Dowel Pin 8×25

2

29

8735090

Retaining Screw M16x40 (LEFT HAND Threaded)

1

30

9911560

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

M20 Plug

1

DRAWN DATE MATERIAL:
WEIGHT:

ANH 31.03.2021

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

21 HEX HEAD 18 20 19

12

11

30

10

28 27 26 25 24 23
1 9 8 7 6 5 4 3 2

17 15 14 13 16

TITLE:
BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

STANDARD GEARBOX ASSEMBLY S350

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

9935260

REVISION 1
A3 SHEET 1 OF 1

ITEM NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

PART NO.
9512000 8705060 9405010 9302120 9305070 9305020 9314000 9304430 9305030 9315040 9312100 8705070 9302110 8705420 9304130 8705090 9315090 9405450 9324070 9304017

DESCRIPTION
Saw Gearbox Socket Head Cap Screw M6x16 Oil Sight Window with Flat Gasket Front Cover Plate Shim 50x60x0.05 Taper Roller Bearing 30x62x17.25 30206 Worm Shaft Key Wormshaft 7x8x31 Taper Roller Bearing 30x72x20.75 30306 Oil Seal 52x30x7 (TC12495) Retainer Ring Socket Head Cap Screw M6x20 Side Cover Plate Flat Socket Head Cap Screw M10x25 Retainer Washer 55×10 Socket Head Cap Screw M6x35 Sum Plug 1/2″ NPT Coolant Pump Pump Mounting Plate Pin – Coolant Pump

QT Y. 1 8 1 1 1 1 1 1 1 1 1 4 1 1 1 3
29
1 1 1 1

21

8705560 Hex Head Screw M8x20

2

22

9505030 Nylon Hose Kit 8mm

1

23

9314050 WormWheel

1

24

9305010 Double Seal 90x70x10

1

25

9814010 Main Spindle S400

1

26

9314420 Key – Main Spindle

1

27

9824000 Spindle Counter Plate S400

1

28

8715140 Dowel Pin 12×30

2

29

8735090 Retaining Screw M16x40 (LEFT HAND Threaded) 1

30

9911560 M20 Plug

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 31.03.2021

1
UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

21 HEX HEAD 18 20 19
12 11 30 10

28

27

25

26

24

23

1

9

8

7

6

5

4

3

2

17 15 14 13 16

TITLE:
BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

STANDARD GEARBOX ASSEMBLY S400

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

9935270

REVISION 1
A3 SHEET 1 OF 1

ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

1

9505540

2

9523040

Coolant Tank (Plastic)

1

Chip Basket

1

A

3

9504170

4

9523050

Plastic Clear Tube ID 8

1

Suction Head – Filter Assembly

1

COOLANT TANK LOCATION

10 9
5 6 7 8
B SUCTION HEAD ASSEMBLY

SUCTION HEAD ASSEMBLY(9523050)

ITEM NO.

PART NO.

DESCRIPTION

QT Y.

5

9302220

Suction Head

1

6

9505005

GREEN FILTER

1

7

9503060

Filtering Disc

1

8

1005230

CIrclip Internal 42

1

9

9305970

Reducing Bush 1/4″ – 3/8″

1

10

9505460

Elbow SIngle Barbed 5/16T x 1/4 BSP

1

TOLERANCES ON DIMENSIONS ARE METRIC SIZE TO MATCH

DIMENSIONS ARE IN MILLIMETERS

6 mm

0.1

ANGULARITY TOLERANCE < 0 10′

30 mm

0.2

CONCENTRICITY 0.1 mm

100 mm

0.3

REMOVE ALL BURRS & SHARP EDGES

300 mm

0.5

BY 0.3 x 45

1000 mm

0.6

UNLESS OTHERWISE STATED

2000 mm

1.2

CAST* 0.5 0.5 1.5 2.0 3.0 5.0

GRADE N1 N2 N3 N4 N5 N6

RA (µm) 0.025 0.05 0.1 0.2 0.4 0.8

GRADE N7 N8 N9
N10 N11 N12

RA (µm) 1.6 3.2 6.3 12.5 25.0 50.0

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN BY DATE
MATERIAL: –
WEIGHT:

ANH 05.06.2020

BROBO GROUP TITLE:
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

2 1 3 4
A COOLANT TANK ASSEMBLY

COOLANT TANK ASSEMBLY

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

9311110

REVISION 0
A3 SHEET 1 OF 1

17 18

1 12 10 13 11
19
9503130 14

15

610

480

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 15.05.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

ITEM NO. PART NUMBER

DESCRIPTION

QTY.

1

9503130

Sheetmetal Stand

1

2

9503150

Saw Stand Shelf

1

4

3

9503160

Stand Brace

1

4

9503130.C08

Cover

1

8

5

8705120

Socket Head Cap Screw M8x20

2

6

8705720

Hex Nut M8

2

7

8705060

Socket Head Cap Screw M6x16

6

7

8

8705750

Hex Nut M6

6

9

9505017

Hinge

2

2

10

9503140

Saw Stand Door

1

11

9505016 Saw Stand Swing Handle (Latch Included) 1

12

8115080

Brobo Logo 65

1

7

13

9505018

“BROBO” Large

1

3

9503130 SHEETMETAL STAND

6

ITEM NO. PART NUMBER

14

9503130.C01

DESCRIPTION Front

QTY. 1

15

9503130.C02

Back

1

5

16

9503130.C03

Top

1

17

9503130.C04

Rod

4

18

9503130.C05

Bended Equal Angle 1.6x50x515

2

19

9503150

Saw Stand Shelf

1

9301720

STAND ANGLE IRON (OPTIONAL)

670

570

465

BROBO GROUP TITLE: BROBO STANDARD STAND

Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

ASSEMBLY

DO NOT SCALE DRAWING DWG NO.

SCALE:1:10

REVISION 0

9501740

A3 SHEET 1 OF 1

ITEM NO. 1 2
3 4
5 6
7 8 9 10 11
12 13 14
15 16 17

PART NUMBER 9915470 8725500
8725540 8705140
8715210 8705650
9911100 9911090 9911180 9911520 9911140
8705720 8705120 9312020
9304030 9305110 SHCSM10x20

DESCRIPTION Pivot Block for Semi-Auto Saw Socket Head Cap Screw M10x35
Roll Pin 6×40 Socket Head Cap Screw M8x35
Hex Thin Lock Nut M8 Socket Head Cap Screw M12x25
Bracket LH (CMG) Bracket RH (CMG) Wheelbarrow Flanged Bearing OD35 ID3/4″ Cylinder Bearing Insert Bracket Lower Support
Hex Nut M8 Socket Head Cap Screw M8x20
Rotary Table
Pivot Shaft Grease Nipple M8x1.25 Socket Head Cap Screw M10 x 20

QTY. 1 4
2 1
1 3
1 1 2 2 1
4 4 1
1 2 2

ITEM NO. 18 19

8 11 12 6

PART NUMBER 9911480 8705340
MOTOR CMG/WEG

DESCRIPTION Gearbox Side Bracket Flat Socket Head Cap Screw M6x16
GEARBOX ASSEMBLY
18 19

QTY. 1 4

4 2 3 14

16 15 1 5

7 9 10 17

PIVOT ASSEMBLY

PIVOT ASSEMBLY ROTARY TABLE
9911460 BROBO CYLINDER
NEW DESIGN GEARBOX SIDE BRACKET

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 19.06.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE: SEMI AUTO SAW GEARBOX SIDE BRACKET ASSEMBLY

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

009002

REVISION 0
A3 SHEET 1 OF 1

NOTE
· SCEW THE INSERTS INTO THE CYLINDER ON BOTH ENDS · DRILL AND TAP M6 AFTER ASSEMBLY · APPLY LOCKTITE ON TO THE GRUB SCREW · MAKE SURE THAT THE GRUB SCREWS GO UNDER THE CYLINDER SURFACE.

20

18

19

16

15

21

17

ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14

PART NUMBER 9911450 9915480 9915490 9915500 9915510 9915520 9915530 9915540 9915550 9915560 9915570 9915580 9915590 9915600

DESCRIPTION Schneider Servo Motor Button Head Socket Screw M8x35 Button Head Socket Screw M8x45
Motor Base Plate Circlip External C Type 20×1.2 Bearing 5204 2RS Double Row 20x47x20.6
Lead Screw TR20x4R Internal Circlip 47×1.75 Groove OD 49.5 Gw=1.85
Aluminium Extrusion AL-8080 x 353 ORing BS222 44×3.6 Brass Top Cover Plate Oil Seal 30x14x7 Piston Assembly

QTY. 1 4 4 1 1 1 1 1 1 1 1 1 1 1

3 12 11

ITEM NO. PART NUMBER

DESCRIPTION

15

9915610

Steel Sleeve 38x30x300

1

16

9915620

Piston Insert OD35x25

1

17

9915630

Screw Nut Brass

1

18

9915650

Rod End Pos Male M16

1

19

9915640

Hex Thin Nut M16

2

20

9911370

Socket Head Cap Screw M16x50

1

21

8705450

Set Scew M6x6

2

10

14

9

8

7

6

5

4

13

2

1

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 02.08.2020

BROBO CYLINDER ASSEMBLY

SILICON ADDED TO PREVENT WATER LEAKS INTO THE MOTOR

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE:

DO NOT SCALE DRAWING SCALE:1:5

DWG NO.
BROBO CYLINDER ASSEMBLY 9911460

REVISION 0
A3 SHEET 1 OF 11

ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
15 16 17

PART NUMBER 9915470 8725500 8725540 8705140 8715210 8705650 9911100 9911090 9911180 9911520 9911140 8705720 8705120 9312020
9304030 9305110 SHCSM10x20

DESCRIPTION Pivot Block for Semi-Auto Saw Socket Head Cap Screw M10x35
Roll Pin 6×40 Socket Head Cap Screw M8x35
Hex Thin Lock Nut M8 Socket Head Cap Screw M12x25
Bracket LH (CMG) Bracket RH (CMG) Wheelbarrow Flanged Bearing OD35 ID3/4″ Cylinder Bearing Insert Bracket Lower Support
Hex Nut M8 Socket Head Cap Screw M8x20
Rotary Table
Pivot Shaft Grease Nipple M8x1.25 Socket Head Cap Screw M10 x 20

QTY. 1 4 2 1 1 3 1 1 2 2 1 4 4 1
1 2 2

8

11 12

6

ITEM NO.
18 19 20 21 22

PART NUMBER
SLA 100L B0-B14A 302996 302995 8705120 8705130

DESCRIPTION
CMG Motor BRACKET MOTOR (CMG) TOP BRACKET MOTOR (CMG) BOTTOM Socket Head Cap Screw M8x20 Socket Head Cap Screw M8x25

QTY.
1 1 1 2 4

22 21 20 19 18

GEARBOX ASSEMBLY

4 2 3 14

PIVOT ASSEMBLY ROTARY TABLE

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 24.02.2020

16 15 1 5

7 13 9 10 17

ACTUATOR UNIT

PIVOT ASSEMBLY

CMG MOTOR SIDE BRACKET DESIGN

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE: SEMI AUTO SAW – CMG MOTOR BRACKET ASSEMBLY

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

010002

REVISION 0
A3 SHEET 1 OF 1

ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
15 16 17

PART NUMBER 9915470 8725500 8725540 8705140 8715210 8705650 9911100 9911090 9911180 9911520 9911140 8705720 8705120 9312020
9304030 9305110 SHCSM10x20

DESCRIPTION Pivot Block for Semi-Auto Saw Socket Head Cap Screw M10x35
Roll Pin 6×40 Socket Head Cap Screw M8x35
Hex Thin Lock Nut M8 Socket Head Cap Screw M12x25
Bracket LH (CMG) Bracket RH (CMG) Wheelbarrow Flanged Bearing OD35 ID3/4″ Cylinder Bearing Insert Bracket Lower Support
Hex Nut M8 Socket Head Cap Screw M8x20
Rotary Table
Pivot Shaft Grease Nipple M8x1.25 Socket Head Cap Screw M10 x 20

QTY. 1 4 2 1 1 3 1 1 2 2 1 4 4 1
1 2 2

8 11 12 6

ITEM NO.
18 19 20 21 22

PART NUMBER
W21_100L 9911390 9911400 8705120 8705130

DESCRIPTION
WEG Motor BRACKET MOTOR (WEG) TOP BRACKET MOTOR (WEG) BOTTOM Socket Head Cap Screw M8x20 Socket Head Cap Screw M8x25

QTY.
1 1 1 2 4

21 20 19 22 18

GEARBOX ASSEMBLY

4 2 3 14

16 15 1 5

7 13 9 10 17

PIVOT ASSEMBLY ROTARY TABLE
ACTUATOR UNIT

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 24.02.2020

PIVOT ASSEMBLY

WEG MOTOR SIDE BRACKET DESIGN

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE: SEMI AUTO SAW – WEG MOTOR BRACKET ASSEMBLY

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

011002

REVISION 0
A3 SHEET 1 OF 1

ITEM NO.
1 2

PART NUMBER 1031360 9515270

DESCRIPTION Handnut
External Circlip 1500-15

QTY. 1 1

3

9305670

O Ring t=3/16″ , ID=2″ , OD=2 3/8″

2

4

9324730

Vice Leadscrew 30×270

1

5

9312210

End Cap

1

6

9305700

O Ring t=1/8″ , ID=5 3/4″ , OD=6″

1

7

9302230

Piston

1

8

9305690

O Ring t=1/4″ , ID=5 1/2″ , OD=6″

1

9

9322190

Air Vice Cylinder Housing

1

10

9304740

Piston Rod Boyler Tube

1

11

9305680

Rod Wiper

1

12

9312200

Vice Jaw

1

13

9314100

Jaw Wear Plate

1

14

8705940

Roll Pin 4×24

1

15

8735490

Button Head Cap Screw M6x12

8

16

2l34002

4 1/8 Fox Swivel Elbow

2

17

8705290

Socket Head Cap Screw M12x75

2

18

9314280

Vice Block Clamp

2

19

8705340 Flat Socket Head Cap Screw M6x16 4

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 26.08.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

19 13 12 11 10 17

9

8

7

6

5

16

4

3

2

1

3

18

16 15 14

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE:
PNEUMATIC VICE ASSEMBLY

Weight ~18 Kg

DO NOT SCALE DRAWING DWG NO.

SCALE:1:5

9311200

REVISION 0
A3 SHEET 1 OF 1

OPTIONAL

10

11

ITEM NO. 1 2 3 4 5 6 7 8 9 10 11

PART NUMBER 9505910 9505940 9512110 8705570 8705580 9501560 9501210 9504320 9501240 9501250 8705170

BOM Table DESCRIPTION
Carriage Track 3.0 Metre Measuring Tape 5Mx19
Angle Bracket Button Head Cap Screw M8x40
Hex Head Screw M8x40 Mirco Flip Included Arm Brobo 68 Kg Conveyor Roller 3000x305x150mm Pitch Adjuststable Stand 610 – 1016 mm Mounting Bracket Conveyor RH Mounting Bracket Conveyor LH Socket Head Cap Screw M10x25

QTY. 1 1 3 3 3 1 2 2 1 1 4

9

7

6

3

2

1

5

4

8

7

6

3

2

1

5

4

9501450 3M LENGTH STOP & CONVEYOR

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 28.10.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

9501460 3M BROBORULE LENGTH STOP KIT

9501490
BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

ITEM NO.
1

PART NUMBER 9505910

DESCRIPTION Carriage Track 3.0 Metre

QTY. 1

2

9505940

Measuring Tape 5Mx19

1

3

9512110

Angle Bracket

3

4

8705570

Button Head Cap Screw M8x40

3

5

8705580

Hex Head Screw M8x40

3

6

9501560

Mirco Flip Included Arm

1

7

9501210 Brobo 68 Kg Conveyor Roller 3000x305x150mm Pitch 1

TITLE:
3M BROBO LENGTH STOP KIT

DO NOT SCALE DRAWING DWG NO.

SCALE:1:18

9501460

REVISION 0
A3 SHEET 1 OF 1

OPTIONAL

10

9

ITEM NO. PART NUMBER

DESCRIPTION

QTY.

1

9505900

Carriage Track 6.0 Metre

1

2

9505950

Measuring Tape 8Mx19

1

3

9512110

Angle Bracket

6

4

8705570

Button Head Cap Screw M8x40

6

5

8705580

Hex Head Screw M8x40

6

6

9501560

Mirco Flip Included Arm

1

7

9501210 Brobo 68 Kg Conveyor Roller 3000x305x150mm Pitch 3

8

9504320

Adjuststable Stand 610 – 1016 mm

3

9

9501240

Mounting Bracket Conveyor RH

1

10

9501250

Mounting Bracket Conveyor LH

1

11

8705170

Socket Head Cap Screw M10x25

4

7

6

8

5

4

3

2

1

9501480 6M BROBORULE LENGTH STOP KIT

7

6

5

4

3

2

1

ITEM NO. PART NUMBER

DESCRIPTION

QTY.

1

9505900

Carriage Track 6.0 Metre

1

2

9505950

Measuring Tape 8Mx19

1

3

9512110

Angle Bracket

6

4

8705570

Button Head Cap Screw M8x40

6

5

8705580

Hex Head Screw M8x40

6

6

9501560

Mirco Flip Included Arm

1

7

9501210 Brobo 68 Kg Conveyor Roller 3000x305x150mm Pitch 2

9501470 6M LENGTH STOP & CONVEYOR

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 22.04.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

TITLE:
6M BROBO LENGTH STOP KIT

DO NOT SCALE DRAWING DWG NO.

SCALE:1:18

9501480

REVISION 0
A3 SHEET 1 OF 1

ITEM NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

PART NO.
9505910 9505940 9504007 9504005 9504000 12131X 9504850 8705750 9505920 8735370 9504008 8726100 8705100 9504010 9504860 9504020 9505930 9502100 9504840 8705340 8715080 8705130 8705070 9504830 8705930

25 23 20 22 21 A

9501590

DESCRIPTION

QT Y.

Aluminium Extrusion 3m

1

Measuring Tape 5Mx19

1

Nylon Wear Strip L90x100x15

2

Carriage 8x90x100L

2

Shaf Support 16

2

Adjustable Hand Levers M10x40

2

Nylon Flat Washer M16 (30x 17x 3)

4

Hex Nut M16 ZINC PLATED

2

Micro Stop (Thumb Nut)

1

Stud M16x250

1

Clamping Pad 50x50x10

2

Button Head Socket Screw M6x16

4

Socket Head Cap Screw M6x40

8

Rotation Arm

1

Nylon Bushes M16 (19x 16.1×17 + 34.5×3) 2

Mounting Plate Shape L2

1

Stop Plate 99 x 85 x 6

1

Extension Arm Stop

1

Wear Plate 50x40x5

1

Flat Socket Head Cap Screw M6x16

5

Dowel Pin 8×25

1

Socket Head Cap Screw M8x25

1

Socket Head Cap Screw M6x20

3

45 Offset Indicator

1

Slotted Spring Pin 4×16

2

14

5

12

11

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 19.06.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

9 2

8

OPTIONAL

9501560 MICRO FLIP

10 9 8 7 6 5 4 3 2 1
15 16 17 24
18 19 20

TITLE:
BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

MANUAL LENGTH STOP ASSEMBLY 3M

DO NOT SCALE DRAWING DWG NO.

SCALE:1:2

9501590

REVISION 0
A3 SHEET 1 OF 2

126 1160
250

2 3
1

1160

1000

ITEM NO.
1 2 3

PART NUMBER
W90x45x1000 W100x20x1160 W100x16x1160

DESCRIPTION 90x45x1000 100x20x1160 100x16x1160
1000

QTY.
3 7 3

30

TOLERANCES ON DIMENSIONS ARE METRIC SIZE TO MATCH

DIMENSIONS ARE IN MILLIMETERS

6 mm

0.1

ANGULARITY TOLERANCE < 0 10′

30 mm

0.2

CONCENTRICITY 0.1 mm

100 mm

0.3

REMOVE ALL BURRS & SHARP EDGES

300 mm

0.5

BY 0.3 x 45

1000 mm

0.6

UNLESS OTHERWISE STATED

2000 mm

1.2

CAST* 0.5 0.5 1.5 2.0 3.0 5.0

GRADE N1 N2 N3 N4 N5 N6

RA (µm) 0.025 0.05 0.1 0.2 0.4 0.8

GRADE N7 N8 N9
N10 N11 N12

RA (µm) 1.6 3.2 6.3 12.5 25.0 50.0

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN BY DATE
MATERIAL: –
WEIGHT:

ANH 09.12.2019

1000

1160

BROBO GROUP TITLE:
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

AS:4068-1993 Flat pallets for materials handling

PALLET ASSEMBLY FOR SEMI AUTO SAW

DO NOT SCALE DRAWING SCALE:1:10 DWG NO.
8815020

REVISION 0
A3 SHEET 1 OF 1

4 59

3

7

8

6

15

18

19

10

1

11

12

13

17 16

15

14

20 21 22 24

ITEM NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

PART NUMBER
9911530 9935790 9935470 9935440 9935450 9935530 9935660 9935460 9911510 9505024 9935280 9315210
DRail 9305600 9935800
EA01 GS01 9911210 9911200 RCK12T-2TEL WAKW 4.4T-2 8745270 9911600

DESCRIPTION
Metal Enclosures SA Enclosure Decal
Stop/E-Stop Push Button Cut Push Button On Off Button LED M22-LED230 Reset Push Button Set Push Button Potentiometer
AC Drives, 3HP, 230V 1PH Input/ 3PH Output AC/DC DIN Rail Power Supply 240 W, 48 V, 5 A
240V AC Contactor Zinc Plated Rail 220 mm Cable Gland Plastic, M20 Cable Gland Plastic, M12
Earth Assembly Ground Sticker
Plug Solenoid Valve 12 Pin Cable & Plug
Cable 4 Pin Bdl 5 Core 30/0.25
Motor Cable

QTY.
1 1 1 2 1 1 1 1 2 1 1 1 1 2 4 1 1 1 1 1 1 1 1

4

2

9

3

5

9

4 7

8

1

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE MATERIAL:
WEIGHT:

ANH 20.08.2020

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

SEMI TITLE: AUTO SAW ENCLOSURE COMPONENTS

DO NOT SCALE DRAWING DWG NO.

SCALE:1:2.5

9911020

REVISION 0
A3 SHEET 1 OF 1

TUBING – 6mm BRACKET
AIR INTAKE GAUGE 12 BAR AIR FR UNIT

TUBING – 4mm

TO PIVOT BLOCK

LOWER BRACKET

MOUNT TO LOWER BRACKET

ROLLER VALVE TUBING – 6mm

AIR VICE 01

REDUCER DOUBLE BANJO
CAM

PILOT/SPRING VALVE

PRESSURE REGULATOR (OPTION)
TUBING – 6mm RETURN LINE AIR VICE 02

ALL RIGHTS RESERVED. THIS DRAWING MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN PERMISSION OF BROBO GROUP PTY LT

DRAWN DATE
MATERIAL:

ANH 12.09.2019

WEIGHT: 12.67

UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS SURFACE FINISH: TOLERANCES:
LINEAR: ANGULAR:

DOUBLE MALE ELBOW

SILENCER

DISTRIBUTOR

TITLE:
BROBO GROUP
Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/

PNEUMATIC DIAGRAM DOUBLE AIR VICE

DO NOT SCALE DRAWING DWG NO.

SCALE:1:4

–

REVISION 0
A3 SHEET 2 OF 2

Control Cords Colour Codes for Brobo Semi Auto Saw

• Supply Power to Stepper motor * Transfer & return signals to stepper PLC

Pin MD-CS610 Wire

1

Brown

2

Blue

3

White

4

Green

5

Pink

6

Yellow

7

Black

8

Gray

9

Red

10

Violet

11 Gray/Pink

12 Red/Blue

Turck RKC12T-x Brown White Blue
Black
Gray Pink Violet Orange Gray/Pink White/Blue White/Gray Gray/Brown

Signal IN4 IN2 INPUT_REF
IN1/CAPTURE
IN3 ANALOG_IN LOGIC_GND SIGNALOUTPUT EMITTER SIGNALOUTPUT COLLECTOR OUTPUT 1+ OUTPUT 2+ OUTPUT 1/2 –

Function General purpose programmable input 4. General purpose programmable input 2.
Biases the input as sinking or sourcing General purpose programmable input with the alternate function of being a
dedicated CAPTURE input. General purpose programmable input 3.
Analog input Logic ground (non-isolated) High speed signal output emitter High speed signal output collector
Output 1 + polarity Output 2 + polarity Output 1 and 2 — polarity

E2019041701

17/04/2019

DELTA VFD-EL PARAMETER

E2019090601 27.04.2021

1. VARI SPEED SAW – AUSTRALIA 1PH 240V SUPPY

PARAMETERS

SET VALUE

FUNCTION

00.03

1

Display the actual output frequency

01.00

95

Max Output Frequency %

01.02

220

Maximum Output Voltage (Vmax) – 3Ph

01.09

3.0

Accel Time 1

01.10

3.0

Decel Time 1

02.00

1

0 To +10V From AVI

02.01

1

External Terminals. Keypad STOP/RESET Disabled

04.08

5

External Reset – No Contact

04.12

20.0

Min AVI Frequency %

07.00

7.8 or 3.9

Motor Rated Current – WEG – or Y

2. SEMI AUTO SAW – AUTSTRALIA 415V – USA 220V OR 460V

PARAMETERS

SET VALUE

FUNCTION

01.00

95

Max Output Frequency %

01.02

415 or 220 or 460

Maximum Output Voltage (Vmax)

01.09

3.0

Accel Time 1

01.10

3.0

Decel Time 1

02.00

1

0 To +10V From AVI

02.01

1

External Terminals. Keypad STOP/RESET Disabled

04.12

20.0

Min AVI Frequency %

Brobo Roller Conveyor
290 x 3000mm Ø50mm Rollers

PART NO: Roller Load Capacity – (each) (kg): Total Load Capacity (kg): Number of Rollers (No.): Table Width (W) (mm): Table Length (L) (mm): Roller Table Height (H) (mm): Roller Diameter (mm):

9501210 60
1200 20
290 3000
80 Ø50

Features
· Roller capacity of 60kg each · 20 x Zinc plated steel rollers at 150mm pitch · Rollers are Ø50mm with commercial bearings · Frames are powder coated · Conveyor is pre-assembled with 7 cross-members · Frames are pre-drilled at 75mm pitch to accept “Optional 19 rollers” totalling to 39 rollers
Please Note: · Roller load capacity is calculated on even weight distribution over entire roller · Total load capacity is calculated on even weight distribution over entire roller conveyor system
Includes
· 20 steel rollers @ 150mm pitch

S107
E

S108
E

S105
E

S103
E

S104
E

+24

M13

AVI

WHT/YELLOW RA

M11 (RUN)
+10V

YELLOW

PINK

YELLOW/BROWN VIOLET

RED

WHITE

RED/BLUE

WHITE/GREY

12

11

12

BLACK

END CUT DETECT STOP/RESET

NOTE
CONNECT BOTH ENDS OF SHIELD TO THE EARTH THE DIODE IS BE MOUNTED ON THE TERMINAL BLOCK

0 14/09/2017 UPDATED FROM RECONENG DRAWING

ANH

BROBO GROUP Address : 8 Fowler Rd, Dandenong VIC 3175 http://brobo.com.au/

OPTION

+24

M13

AVI

S107
E

S108
E

S105
E

S103
E

S104
E

WHT/YELLOW RA

M11 (RUN)
+10V

YELLOW

PINK

YELLOW/BROWN VIOLET

RED

WHITE

RED/BLUE

WHITE/GREY

12

11

12

OPTION

END CUT DETECT STOP/RESET

BLACK

NOTE
CONNECT BOTH ENDS OF SHIELD TO THE EARTH THE DIODE IS BE MOUNTED ON THE TERMINAL BLOCK

0 14/09/2017 UPDATED FROM RECONENG DRAWING

ANH

BROBO GROUP Address : 8 Fowler Rd, Dandenong VIC 3175 http://brobo.com.au/

OLD VERSION

OLD VERSION

OLD VERSION

OLD VERSION

A
SECTION A-A

UNCONTROLLED IF PRINTED – CHECK CURRENT REVISION

THIS DRAWING IS THE CONFIDENTIAL PROPERTY OF RECONENG-IE PTY LTD AND SHALL NOT BE USED IN PART OR WHOLE WITHOUT PRIOR WRITTEN PERMISSION FROM RECONENG-IE PTY LTD. THIS DRAWING IS NOT A VALIDATED DESIGN AND ITS FITNESS FOR PURPOSE IS NOT WARRANTED UNDER ANY CIRCUMSTANCES UNLESS IT HAS BEEN VALIDATED BY BOTH ANALYSIS AND TEST. THIS DRAWING IS RECONENG-IE PTY LTD INTELLECTUAL PROPERTY WITH ALL RIGHTS RESERVED.
174

A

588

87

3

BACK VIEW SCALE 1:2

03 MACHINED CONNECTION PLATE ADDED REV.

DESCRIPTION REVISIONS

3

208242

4 BOLT CAP/SCR, M5 20 LN, SOCKET HEAD –

2 9911460

1 ACTUATOR, 200 STROKE – ASSEMBLY – –

1 9911450

1 STEP MOTOR, DOUBLE STACK –

1 2

ITEM NO.

Number

Rev

QTY.

UNLESS OTHERWISE SPECIFIED DR.BY

DIMENSIONS ARE METRIC

GENERAL LINEAR/ANGULAR & CHK.BY

FORM AND POSITION TOLERANCES ACC. TO DIN ISO 2768-mK

CH.DR.

O.DJ. 29.03.2013 S.R. 07.06.2016

Name & Material
RECONENG Industrial Engineering www.reconeng.com.au

07.06.2016 DATE

S.R. CHK.

Size To Mach. 6 mm ± 0.1 30 mm ± 0.2
120 mm ± 0.3 400 mm ± 0.5 1000 mm ± 0.8 2000 mm ± 1.2
MACHINE
FINISHES
THIRD ANGLE

MATERIAL
ASSEMBLY
STOCK
–
DIMENSIONS
–
FABRICATIONS

Approved
TITLED
ACTUATOR, MD34AC DRIVE, 200 STROKE

WEIGHT
–
SCALE
1:2

SIZE PART/FILE NO.

REV.

A3

AC80L

03

BREAK SHARP EDGES AND REMOVE ALL BURRS

SHEET 1/1

CHAPTER 5 –

Adjustments to the Saw Unit

5.1. Changing the Blade
To replace a worn saw blade:
DA NG ER ­ ELEC TRO C UTIO N
Make certain that the power to the saw is turned off before proceeding with changing the saw blade.

1. Disengage the linkage arm that is between the guard linkage system & pivot block (at the pivot block by compressing the spring & moving the bolt through the slot).
2. Slide the saw guard up as far as possible (as if it was opening during a cutting cycle) to gain access to the spindle nose.
3. Loosen the spindle screws (LH thread), using the 14mm hexagonal wrench provided, & remove the counter plate. To loosen the spindle screw, insert the wrench (short end) into the socket head cap screw & firmly knock the wrench with the palm of your hands until the screw is loosened. If this method fails to free the screw, place a piece of timber under the blade of the machine, & loosen (or tighten) the screw while holding the saw head of the machine down (blade against the timber).
4. Remove the worn saw blade away from the spindle hub. Using a soft brush, clean the face of the spindle, counter plate & mounting faces of the blade of any dirt or swarf that was trapped by the previous cutting cycles.
5. Place the old saw blade into the new blade packaging & disposed of it safely. Carefully mount the new blade onto the spindle hub, ensuring that the blade is rotating into & towards the back fence, & replace the counter plate utilizing the drive pins as guides as it passes through the pinholes on the blade.
6. Rotate blade back against the drive pins in a counter-clockwise & finger tighten the spindle screw. 7) Firmly retighten the spindle screws, ensuring that the saw blade spins uniformly & aligned parallel with the
   safety guard. 8) Lower the outer guards & make certain the pin of the linkage arm is re-engaged with the track on the inner
   guard & reconnect the guard linkage. 9) The new blade is ready for use. To check that the blade is performing correctly, carry out a sample cut on
   a piece of off-cut. 10) If optional devices are supplied, mount the stock support & rollers on either side of the clamping table.
   Normally stock should feed on the left to right, but it can be feed from the right to left if required.
   Bro b o G ro up brobo.com.au

5.2. Adjusting the Cutting Angle

The back jaw wear-plates on the Brobo Group SA350/400 Semi-Automatic Saw are typically fitted in the following manner. For angular cutting, the wear plates should be repositioned to provide the maximum support on one side & clearance on the other (Figure 20).

Standard Cut

Angular Cut 450

Figure 20. Angular Cut Positions
i. To adjust the angle of the cutting surface, loosen the socket head screws shown in Figure 10, located on the back jaw face that clamps the table, using the hexagonal wretch provided.
ii. Fine-tune the angle required. The shot-pins have positive locations at 90 & 45 right & left. Adjust the angle on the back fence to suit.
iii. Re-tighten all the previously loosen socket head screws. The saw is now ready for use.
5.3. Cutting & Feeding Speeds
As previously highlights, the rate of feed largely affects the quality of the final cut. As such, the blade life is also dependent on the feed at which it is cutting the sample material – in particular, the type of material & also the crosssectional dimensions. Thus, to extend the life of the blade, maintain a firm & steady pressure whilst allowing the blade teeth to cut at an optimum rate. Do not force the blade through the material! This could cause numerous problems including breaking the blade teeth, jamming the blade with the cutting part or fracturing the blade spindle.
The cutting action also generates a large amount of heat within the cutting sample due to frictional contact. Should this heat affect the material you are cutting in any way, the heat should be dissipated using the coolant system.
5.4. Refilling the Lubricator
To refill the lubricator bowl, twist the bowl anti-clockwise & slide it down to detach it from the lubricator unit (There is no need to disconnect the air supply to the unit). The unit can now be refilled to the line positioned near the top of the bowl, which is approximately 10 millimeters from the top edge of the bowl. Do not fill the bowl above this line, as the lubricator unit will not function properly. Replace the lubricator bowl in a reverse manner by sliding the bowl upwards, ensuring that the feed tube is located inside the bowl, & twist it clockwise to lock it into position.
Bro b o G ro up brobo.com.au

5.5. Adjusting the Brobolube Unit
When assembled, the Brobolube unit is a precise instrument that supplies an accurate quantity of lubricant directly to the saw blade before it contacts the workpiece. There are 2 control variables available for the operator:
Air Flow (Volume) Delivery Regulated with the tap (needle valve), this can be adjusted from initial, completely closed to fully open states. It is highly recommended that the upper end of the flow range be utilized to allow adequate airflow to deposit & evenly distributed the lubricant onto the blade while maintaining a fine lubricant mix. If the needle valve is not open sufficiently, the air to lubricant ratio may vary & may result in a substandard distribution of lubricant to reach the blade teeth.
Lubricator Flow Rate This controls the fluid flow rate & is adjustable via the slotted needle valve situated on top of the lubricator. The consumption of Brobolube is factory set to 4 drops per minute. This has been examined to produce a sufficient mix of air & lubricant, & it is recommended to use this initial setting. On this setting, approximately 55 cubic centimeters (lubricator capacity) should last for 20 hours of continuous cutting. If for some reason the setting needs to be altered, the needle valve should be turned clockwise to reduce or anti-clockwise to increase the fluid flow respectively.
NOTE i. Although the lubricator is capable of delivering a much higher flow rate of lubricant, it is suggested that you
do not increase the flow rate excessively because: No significant increase in blade life or lubricating efficiency will be achieved (confirmed by test results). Excessive application of Brobolube will only result in a waste of fluid. The excessive application will produce swarf that will be wet (oily) & harder to clean up than dry swarf
produced from the correct supply of Brobolube. ii. The amount of Lubricant (when set correctly) delivered by the lubricator is not easily visible to the naked
eye. If in doubt that lubricant is being delivered, first check to see if lubricator itself is delivering droplets at its sight glass. If still unsure whether lubricant is being delivered, disconnect the supply tubing to the tap (needle valve) & hold the tube against some blotting paper for a few seconds while the lubricator is operating.
Bro b o G ro up brobo.com.au

5.5.1. Lubricating Oil Precautions – Health Hazard Information
The Brobolube lubricating fluid has no known adverse health effects. “Brobolube” is non-toxic, odourless, nonflammable below approximately 350ºC, & non-corrosive, although it may affect some types of rubber. There are no traces of sulfur, chlorine, phenol or nitrates found in Brobolube. When comes into contact with skin, the oil may be removed by wiping away the excess, then washing the contaminated area with detergent & water. If the oil is utilized at high temperatures, appropriate protective apparel should be worn as the oil could cause burns to skin or eyes. If splashed by hot oil, immediately run cold water over the burn area & apply first aid burn treatment. If the Brobolube delivery line breaks or becomes disconnected during operation, ensure that the air supply to the system is disconnected before repairing the problem. It is recommended that footwear with anti-slip soles be worn at all times. Any spills will result in potentially hazardous slippery surfaces & should be dealt with promptly to prevent physical injury resulting from falls. Do not use coarsely, combustible material like sawdust to soak up oil due to the potential risk of spontaneous combustion. Spilled oil should be transferred into non-porous containers of suitable strength. Any remaining oil should be cleaned up with sand or other non-combustible, absorbent material. Place the sand & oil mixture into containers & disposed of by an EPA approved landfill or alternatively, by a suitable non-polluting method. In addition, rags soaked in oil should not be burned. Do not pour oil down the drain, which would ultimately contaminate the water supply & pollute the environment.
For firefighting purposes, either use CO2, dry chemical or foam retardant to extinguish the flames.
Bro b o G ro up brobo.com.au

CHAPTER 6 ­

Maintenance & Selection of Consumables

6.1. Role of the Operator
The person operating & maintaining the Brobo Group SA350/400 Semi-Automatic Saw must familiarise themselves with these instructions for their own safety & that of the others, in addition to safeguarding the production of the machine. Responsibility must be taken by the user on the general maintenance & up keeping of the unit as specified in this chapter, with particular emphasis on:
Check to ensure that other operators of the machine always aware of and comply with the relevant safety instructions & standards as specified in Chapter 2 – Safety & Accident Prevention. Therefore, check that the safety devices are operational & work perfectly and that personal safety requirements are complied with.
Ensure that the working cycle is efficient & guarantees maximum productivity, inspect the: o Functions of the main components of the machine o The sharpness of the blade & coolant flow o Correct working parameters for the type of material being cut
Verify that the quality of the cut meets the requirements & the final product is free from any machining defects.
6.2. Maintenance Requirements
All maintenance must be carried out with the power switched off & the machine in emergency stop condition.
To guarantee optimum operation, all spare parts must be Brobo Group originals.
On completion of maintenance works, ensure that the replaced parts or any tools used have been removed from the machines before starting it up.
Any behavior not in accordance with the instructions for using the machine specified in this manual may create hazards and/or safety risks for the operator.
Therefore, read & follow all the instructions for use & maintenance of the machine, and those on the product itself.
6.3. General Maintenance of Functioning Components
The general maintenance operations that should be carried out regularly are as follows:

1. Keep the vice clamps, overall machine & path of the cutting blade free of any offcuts, accumulated swarf & coolant using compressed air or preferably thread-free cloth.

2. Observe the oil level on the gearbox. The first oil change should be performed after the initial 60 hours of operation & 500 hours of operation thereafter. Use Brobo Gearbox Oil (Part No. 9501090)
   Refilling point is situated in the handle bar mounting threaded hole. The required quantity to refill is 800 ml for the S315/S350/400 gearboxes.
   Brobo Group brobo.com.au

3. Change coolant as required, or whenever the coolant starts to get dirty or emits a stale odour. The coolant compensation tank should be checked regularly. Coolant level would expect to naturally decrease over time due to natural evaporation. Use premium quality coolants such as CoolTech 500 or SlideTech 68. Coolant is available from BROBO GROUP Pty. Ltd. in 2 litre & 20 litre packs (Part No. 9301570 & 9501080): Concentrate, Ratio 1:20

4. Lubricate the saw head pivot shaft & rotary table regularly (after every 40 hours of operation, or weekly) with an NLGI 2 extreme pressure grease, Shell Alvania No.1 grease or equivalent.

5. Clean the vice & lubricate any moving joints or sliding surfaces with good quality oil. 6) Clean the machine regularly & keep any unpainted surfaces lightly oiled to protect from rust & corrosion. 7) The air supply for the pneumatic air vices should be checked regularly such that it is free of any condensed
   water molecules & the filter should be drained frequently. 8) Ensure that the machine performs cuts perpendicular to the work surface.
   If not, contact Brobo Group engineering department. 9) Test that the blade is at right angles to the workpiece back fence.
   If not, contact Brobo Group engineering department. 10) Check that the 0 notch on the fixed worktable is aligned with the graduation on the turntable. If not, adjust
   as described in Section 5.2. 11) Examined that the precision of the 15, 30, 45 left & right stops are correct & accurate. If they are not
   adjusted properly, proceed as described in Section 5.2. 12) Regularly empty out the swarf catcher, resting directly above the compensation tank, of any offcuts & swarf
   that has collected during the numerous cutting cycles.
   Bro b o G ro up brobo.com.au

CHAPTER 7 –

Troubleshoot

7.1. Troubleshooting For Blade & Cutting Problems

PROBLEM IDENTIFIED
Cuts produced are not at 90 and/or are not perpendicular

DIAGNOSIS
Head speed too low or too high

SOLUTIONS
Reduce or increase head speed respectively.

Blade with worn teeth

Replace with a new blade, with reference to Section 5.1 Changing the Blade.

The angularity of blade to workpiece back fence and vice clamps

Adjust the position of the blade so that it is at right angles to the workpiece back fence using the 0 notch as a reference; set the stops at 45 left & right using the method described in Section 5.2 Adjusting the Cutting Angle.

Blade not perpendicular to the work surface

Adjust the blade using the appropriate screws such that it is perpendicular to the work surface.

Frequent and/or excessive teeth breaking

Broken teeth Incorrect lubricant/coolant fluid
Material too hard Blade not worn incorrectly

Check the hardness of the material being cut corresponds to the capabilities of the blade.
Check the water & oil mixture; check that the holes and/or hose are not blocked; direct the nozzles correctly; check that the lubricant/coolant fluid conforms to those specified in Section 6.3 General Maintenance of Function Components.
Check the cutting speed, feed speed, blade type & parameters are correct for the particular application.
With a new blade, it is necessary to start cutting at half feeding speed. After a normalizing period (cutting surface about 300cm2 for hard materials & 1000cm2 for softer materials), both cutting & feed speeds can be brought up to normal values.
Bro b o G ro up brobo.com.au

Rapid teeth wear Broken blade

Blade with an incorrect excessive fine tooth pitch

and/or

As excessive pressure is exerted on the incorrect teeth profile, replace the blade with correct tooth pitch dimensions & profile.

Workpiece not clamped firmly in place

Any movement of the workpiece during the cutting process can cause broken teeth; check the vice clamps, clamping jaws & clamping pressure is satisfactory.

Excessive vibrations

Specimen vibrates in the vice; check that the vice clamps are position correctly & the clamping pressure is adequate.

Head speed too slow or too high

The blade/slide runs over the material without cutting it; increase or decrease head speed respectively.

Reduce cutting pressure

Cutting pressure to high Insufficient coolant
The non-homogenous being cut

Check the coolant level & clean piping & nozzles

material

The material present may not be homogenous either on the surface, such as oxides or sand present or in sections, such as under-cooled inclusions. The variances in grain development cause the premature wearing of teeth & consequently, break as the result. Homogenise or clean these materials.

Reduce head speed

Head speed to high
Teeth in contact with the material before commencing the cut

Always check the position of the blade before starting an initiating a new cut or job
Check the coolant level & clean piping & nozzles

Insufficient coolant Excessive vibrations

Specimen vibrates in the vice; check that the vice clamps are position correctly & the clamping pressures are adequate

Bro b o G ro up brobo.com.au

7.2. General Troubleshooting
Below lists of some of the most commonly identified problems associated with the Brobo Group SA350/400 SemiAutomatic Saw and the recommended troubleshooting procedures to undertake to rectify the situations. If the solutions provided do not resolve the problem, or the problem identified differs from those listed, immediately contact Brobo Group engineering department.

PROBLEM IDENTIFIED
Spindle motor will not rotate

DIAGNOSIS
Electrical power supply not connected

SOLUTIONS
Ensure that the main power cable is plugged in & switched on. Check the phases, cables, plugs & sockets for loose connection. Also, check that the motor connections are in place.

Loose contactors

Verify that the contactors are not loose. If contacts are short-circuited, contact Brobo Group engineering department immediately

Motor burnt out

Check that it has not burnt out, that it turns freely & there is no moisture in the main electrical unit. The winding can be rewound or replaced

Blown fuses

Examine that the fuses are intact & fitted correctly, otherwise replace or tighten the fuse holders

Inverter Wiring

Inverter display shows RD0 when ready. Check the integrity of connection B2 to B4.

Machine open slowly or not at all

Check for any leaks present within the

Hydraulic oil level and pressure catchment unit. Top up the with

system

coolant as recommended in Section

6.3 General Maintenance of

Functioning Components

Coolant system not operational

Check that it is not kinked, severed or blocked. Flush out any blockages

Bro b o G ro up brobo.com.au

PROBLEM IDENTIFIED
Vice clamps do not engage
Saw stops actuation while cutting, not proceeding any further into the cut. The cutting head will not ascend or descend
The blade will not reach a maximum cutting depth Workpiece deformed by a clamp

DIAGNOSIS
Air supply hose is not connected

SOLUTIONS
Inspect that the air supply cable is connected to the air fittings located at the back of the saw

Emergency condition tripped

Check that the emergency stop button is released, specified in Section 3.1.4 Control Panels. Check the contacts & the cable connections

Air treatment unit obstructed

Check that the pneumatic input & inlet connections are not obstructed & that the supply hose is not blocked or kinked

Blocked pneumatic tubing

Check that it is not kinked, severed or blocked. Remove any blockages

Solenoid issue

Check that the solenoid is working. The solenoid will display a red light if it is on. Check the wiring of the solenoid. If there are no issues with wiring connections replace the solenoid.

There is a physical obstruction to the head coming down

Check if the adjustment screw is too high. Check if the actuator is not jammed. Check if there is a jam on swarf at the pivot point.

Power supply not switched on

Ensure that the main power cable is plugged in & switched on. Check the phases, cables, plugs & sockets for loose connection. Also, check that the motor connections are in place

Emergency condition tripped

Check that the emergency stop button is released, specified in Section 3.1.4 Control Panels. Check the contacts & the cable connections

Loose connectors

Check that the orange power connector at the actuator is not loose.

Faulty feed jog switches

Contact Brobo Group engineering department for replacement of part

Actuator jammed

Remove motor which requires four screws to be removed from the motor & actuator. Remove the motor. Using a flat head screwdriver, insert the screwdriver into the keyway & rotate. Rotate clockwise when head will not ascend. Rotate anticlockwise when head will no descend.

Depth adjustment screw not fully released. Release the screw & recalibrate the saw. Saw must be recalibrated every time the screw is adjusted.

Tighten the depth adjustment screw fully

Clamp pressure too high

Lower the air pressure going to the clamps.

Bro b o G ro up brobo.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>