zehnder 9821-00 CO2 Sensor Instruction Manual

zehnder 9821-00 CO2 Sensor Instruction Manual

Foreword

Refer to the full manual for detailed information and the applicable safety and installation regualtions.

Questions
For all questions and the latest full manuals, you can contact your Zehnder branch. Contact details are provided at the back of these quick start installer and user instructions.

These manuals, other product information and instructional videos can also be accessed by scanning the QR code.

All rights reserved
This installation manual has been compiled with the utmost care. However, the publisher cannot be held responsible for any damage caused by failure to follow safety or operating instructions. In the event of disputes, the Dutch text prevails.

Reading guide
The following symbols are used in this installation manual to draw the reader’s attention to safety aspects and important information:

Point of attention

Risk of compromised performance or damage to the ventilation system

Risk of personal injury

Features and benefits

The CO2 Sensor measures the amount of CO2 in the air of the room in which this sensor is installed. The device sends the results to the ventilation system. If the CO2 level is too high, the system regulates the ventilation based on the maximum CO2 values.

In this way, healthy air quality in the room is maintained.

Reducing high CO2 values in the home is conducive to concentration, good sleep quality, and helps prevent headaches

Safety

The CO2 Sensor may only be used in the manner described in the user manual.

Always follow local safey regulations when using this device.

The device may only be used if it has been properly installed according to the instructions and guidelines found in the installation manual.

The device may be used by: children of 8 years and older; persons with reduced physical capabilities; persons with reduced sensory capabilities; persons with reduced mental capabilities and persons with lack of experience and knowledge as long as they are under supervision or have received instruction for safe use.

The device may only be intalled and maintained by a qualified professional.

The responsibility for the correct use of the device lies with the end user. The manufacturer cannot be held responsible for any (consequntial) damage caused by inexpert, incorrect, or inadvisable use.

Do not get the device wet. Do not install it in a damp place.

Safety regarding assembly and installation

The CO2 Sensor may only be installed as described in the corresponding installation manual. The sensor is connected to 120V power. All electrical work should be done by a qualified professional and follow local code and regulations

Safety regarding use

The CO2 Sensor may only be used as described in the corresponding used manual.

intended use of the device

The CO2 Sensor measures the amount of CO2 in the air of the room in which this sensor is installed. The device sends th results to the ventilation system.

Inexpert use of the device

Do not open the casing. The installer makes sure that all parts that can cause personal injury are behind the casing.

Children must not play with the device.

Children must not clean and maintain the device unsupervised.

Changes or modifications not expressly approved by Zehnder America could void the user’s authority to operate the equipment.

Disassembly and disposal

If the CO2 Sensor is disassembled, the waste disposal regulations applicable on-site and at the time of the disassembly must be observed.

Dispose of the CO2 Sensor in an environmentally friendly way. Do not dispose of the unit together with household waste. The CO2 Sensor can be handed in at a collection point for electronic waste.

It is the responsibility of the owner of the CO2 Sensor to dispose of the unit responsibly

CO2 RF & 0-10V Sensor Legend

Figure 4.1 – Front of the CO2 Sensor

Legend

1. Top LED
2. Middle LED
3. Bottom LED
4. Operating button
5. CO2 LED

Commissioning the CO2 RF Sensor

1. Activate the pairing mode of the ventilation unit.|

• All ventilation units (except the ComfoAir Q): turn off the electrical current from the ventilation unit, wit at least 5 seconds and then switch the current on.
• ComfoAir Q with RF receiver: activate the menu on the ventilation unit via ADVANCED SETTINGS > RF SETTINGS > START RF PAIRING

---|---
2. Activate the menu.|
3x
CO2
CO2
3. Confirm the menu selection to start RF pairing.|
3x
4.Select the type of RF Pairing.|
Repeat step 3; select the desired pariing.|

1. Standard pairing mode
2. Connect to an additional ventialtion unit
3. Generate a new ventilation unit address

5. Confirm the selected pairing.|
Duration: about 1 minute.| CO2
CO2
6. Repeat the pairing procedure for the next CO2 Sensor.|

• Start at step 1.

Status Display

Figure 6.1 – Front of the CO2 Sensor

Legend

1. Top LED
2. iddle LED
3. Bottom LED
4. Operating button
5. CO2 LED

| Operating button
---|---
|

1. Manual position 1 (low)
2. Manual position 2
3. Manual position 3 (high)2 (normal)

CO2  | The CO2 level display is off
= the current CO2 level1x
CO2 | The CO2 level is fine
CO2 ✸ | The CO2 leve has increased
CO2| The CO level is too high
2Select automatic ventilation or manual mode 3 (high). Does the CO2 LED stay red? For extraventilation, open windows and/or doors.

Advice for manual ventilation modes

The CO2 Sensor is intended for automatic ventilation. If installed correctly, it will provide sufficient ventilation in the room where it is installed. In certain cases, it is recommended to select a manual ventilation mode:

• Manual mode 2 (normal): for a few peopl in a living room without a CO2 Sensor
• Manual mode 3 (high): for many people in rooms without a CO2 sensor

Setting the ventilation mode

1. Select the manual ventilation mode.|
---|---
2. Repeat step 1 for the desired ventilation mode.| Mode 1Low| Mode 2Normal| **** Mode 3High| Ventilationbased onCO2 value

After a maximum of 12 hours, the system automatically returns to control based on the measured CO2 values.

LED brightness setting

1. Activate the menu.|
---|---
3x CO2
30 sec
2. Select the brightness menu.|
3. Open the brightness menu.|
3x
4. Select the desired brightness.|
5. Repeat step 4 for the desired brightness.| CO ✸(4x) Bright to dimCO ✸(1x)
CO2 warnings only2
CO2  ❍ (1x) Off2
6. Confirm your choice.|
3x

925 MHz operational frequency

FOR USE IN ITU REGION 2 ONLY (Americas)

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit di ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Zehnder could void the user’s authority to operate the equipment.

Supplier’s Declaration of Conformity 47 CFR §
2.1077 Compliance Information

CO2 Sensor RF67
Zehnder America
6 Merrill Industrial Drive, Suite 7
Hampton, NH 03842 USA
603 601 8544 www.zehnderamerica.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

References

• Zehnder HRVs and ERVs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>