DT Research DT382DN Rugged Tablet User Guide
- June 14, 2024
- DT Research
Table of Contents
DT Research DT382DN Rugged Tablet
Specifications:
- Product : Rugged Tablet DT382DN
- Manufacturer : DT Research, Inc.
- Address : 2000 Concourse Drive, San Jose, CA 95131
- Model : DT382DN
Product Usage Instructions
Package Contents:
The DT382DN package includes a rugged tablet, battery, power adapter, and
various input/output ports for connectivity.
Button Functions:
- Power Button: Used to power on, standby, and power off the tablet.
- Windows Key Button: Accesses Windows functions.
- Programmable Buttons: Customizable for specific functions.
- Brightness Control Buttons: Adjust screen brightness.
- RFID Reader Trigger Button: Activates RFID reader.
- Barcode Scanner Trigger Button: Initiates barcode scanning.
Operation:
To power on the tablet, press and quickly release the Power Button. For
standby mode, press the Power Button briefly. Use software functions to safely
power off the device for extended storage. Ensure to charge the battery pack
fully using the AC-DC adapter before initial use.
Start-Up:
Upon successful startup, the interface will be displayed after a few seconds.
Wireless LAN connection may take additional time to establish.
Wireless Networking:
For setting up the UHF RFID reader, refer to the provided steps. Contact your
device provider for the UHF RFID reader API package if needed.
Data Capture Module Operation Guide:
To optimize system performance, activate only the symbologies required for
your operations.
Pole/Vehicle Mount Cradle:
The optional mount cradle allows secure installation of the tablet in vehicles
or on poles for stable operation.
For More Support:
Users can download additional operation guides from the DT Research website
for detailed assistance with tablet modules and features.
INTRODUCTION
The DT Research DT382DN Rugged Tablet features the integration of a high brightness 8” capacitive touch screen and a high performance yet energy- efficient processor within a slim, lightweight, durable package. With built-in Wi-Fi and a smart card reader as well as options for a back camera, barcode scanner, GNSS, NFC, and UHF RFID reader, this robust tablet offers seamless information capture and transmission for improved workflow. Rated IP65 and MIL-STD-810H, the DT382DN Rugged Tablet provides reliable operation in harsh, mission-critical environments.
PACKAGE CONTENTS
- One DT382DN
- One Battery Pack and Handstrap
- AC-DC Power Adapter
- Basic Operation Guide
The actual package contents may vary depending on the configuration acquired.
The DT382DN
Input/Output Ports
-
USB Type-C Port (power input)
-
Audio Jack
-
USB Port
-
DC-in Jack
Data Capture Modules -
Smart Card Reader or
-
Standard SD card reader
-
Barcode Scanner (optional)
-
Back Camera (optional)
Button Functions
BUTTON ACTION
- Power Button
- Windows Key Button
- Programmable Buttons
- Brightness Control Buttons
- RFID Reader Trigger Button
- Programmable Button
- Barcode Scanner Trigger Button
- Programmable Button
PRECAUTIONS
- Always exercise care when operating and handling the DT382DN
- Do not disassemble any portion of the DT382DN, as this will void any product warranty.
- Do not use any power adapter or charging cradle other than the one provided with the tablet or acquired from the manufacturer or its partners.
- In the unlikely event that abnormal noise, strange odour, or smoke is present, immediately power down the DT382DN and disconnect all power sources. Please report the problem to your device provider immediately.
OPERATION
Powering ON and OFF
To activate DT382DN, push and quickly release the Power Button. The display
will come on in a few seconds. To put the DT382DN in standby mode, push and
quickly release the Power Button. To turn the DT382DN off for extended
storage, power off safely using any software function that “shuts down the
computer” provided in the software operating system.
NOTE:
- The battery packs shipped with your tablet may be low in power – please use the AC-DC adapter with the DT382DN when setting up for the first time to fully charge the battery pack.
- To conserve power, push and quickly release the Power Button to make the tablet in standby mode while not in use. Pushing briefly on the same button will wake up the system.
- When the battery pack is charging, the blue-coloured Battery LED should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking activity and the LED stays dark, the battery pack(s) may have been drained substantially. Unplug/replug the
- AC-DC adapter to the DT382DN a few times to activate the charging process.
- Avoid using the Power Button (“hold 4+ seconds” feature) to turn off the tablet—this form of hardware shutdown is intended to be a means of recovery from lockups, and not as normal operation.
Start-Up
If the power-up (from Standby mode or otherwise) is successful, the appropriate interface will be displayed after a launch sequence of several seconds. The wireless LAN connection may take 10-15 seconds to be established.
Wireless Networking
Wireless LAN
The DT382DN is often delivered with an embedded (user-inaccessible) 802.11ac
LAN adapter equipped with a hidden custom antenna.
- Through the support of typical WLAN adapters, the DT382DN should be able to detect all 802.11 access points in the vicinity for you to select the access point of your choice for connection.
- The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT382DN and the access points have to match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access.
- When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, etc.
- Refer to the access point operating manuals for setting up the 802.11 access points.
Data Capture Module Operation Guide
If your DT382DN comes with an RFID Reader refer to the steps below to
configure the settings.
UHF RFID Reader:
The optional UHF RFID reader supports EPC Gen2V2 and ISO 18000-63 standards.
To develop an application to use the UHF RFID reader, contact your device
provider for a UHF RFID reader API package
NOTE :
To ensure the system performance, turn on only the symbologies you are going
to use.
For More Support
Users can download the Tablet Modules Basic Operation Guides from the DT
Research website.
Pole/Vehicle Mount Cradle
The optional pole/vehicle mount cradle can be used to secure a DT382DN tablet
in a vehicle or forklift for easy and stable operation.
Installation
The DT382DN rugged tablet is a purpose-built stationary tablet to be installed
on a pole/vehicle mount cradle with a stand to provide enhanced mobility and
user experience. The DT382DN rugged tablet is designed to serve as a floor
control unit to work with the user’s advanced security screening system. The
hot-swappable battery design allows the control units to be installed
virtually anywhere while eliminating the hassles and need for power outlets
and network cabling. The use of a battery power tablet allows the
customer’s advanced screening systems to be installed at both indoor and
outdoor venues while providing extended working time for enhanced
productivity, which in turn reduces system downtimes for optimised user
experience when going through security checkpoints. The 8” display provides
clear information for security staff to effortlessly monitor the screening
systems, while the pole/vehicle mount cradle provides stable operation for a
higher level of safety while being used on site while eliminating the risk of
accidental removal or theft.
To mount a DT382DN tablet onto the pole/vehicle mount cradle:
-
Step 1.
Place the DT382DN tablet beside the pole/vehicle mount cradle. -
Step 2.
Pull the upper clamp of the pole/vehicle mount cradle to widen the space for mounting the tablet. -
Step 3.
Place the DT382DN tablet in the mounting space of the pole/vehicle mount cradle. -
Step 4.
Release the upper clamp to secure the tablet in place.
NOTE:
- DO NOT carry around the DT382DN rugged tablet when operating.
- DO NOT use the DT382DN rugged tablet when it is not properly mounted onto the pole/vehicle mount cradle.
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.