Jartoo JT-VBM002 Baby Monitor User Manual

: June 13, 2024
: Jartoo

Jartoo JT-VBM002 Baby Monitor User Manual

SAFETY INSTRUCTIONS

Keep cord out of the reach of children (more than 3ft / 0.9m away) in case of STRANGULATION.

NEVER place the camera or cord in or near the crib or playpen.

NEVER mount the camera directly above the crib or playpen to avoid the risk of
Only use the AC adapters
Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement,
Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce
Only use attachments and accessories speciﬁed by the
Unplug this device when unused for long periods of

CAUTION

NOT toys. Do not allow children to play with them.

This product is NOT intended to replace the proper supervision of You MUST check your child’s activity regularly.
This product is not intended for use as a medical camera and its use should not replace adult
Unplug the product during lightning
Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after
Check the reception Test the camera before use and after changing the camera’s location.
Clean the camera with a dry cloth
Do not block any ventilation

Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.

PACKAGE CONTENTS

Jartoo Baby Monitor & Camera (Model: JT-VBM002)

Monitor Adapter (5V 2A )
Camera Adapter (5V 2A)
Micro USB Cable *2
User Manual
Warranty

PRODUCT DIAGRAM

Camera

Light sensor
Lens
Microphone
Power Switch
Power indicator
Microphone
Speaker
USB-C
Camera Antenna
Temperature Sensor Mounting Hole
Pairing Button

Baby Monitor

Antenna
Volume Indicators
Power Indicator
Charging Indicator
Microphone
Talk Button
Zoom Button
Left Button
Up Button
Right Button
OK Button
Down Button
Menu Button Back
Button Lolume
Control Power
Button Back
Stand Speaker
USB-C Port

Press and hold the Talk button to speak the camera.
Press Power button to switch on/off the monitor screen. Press and hold the Power button 2 seconds to switch on/off the monitor.

GETTING STARTED

1.Charging & Powering Baby Monitor

Connect the monitor adapter to the monitor and a power
Unplug the unit when its power indicator turns off, indicating a full
Press and hold the Power button on the monitor to power on

Powering Camera

Connect the camera to power source via the TYPE-C cable and camera
Slide the Power Switch on camera to power on. Make sure the power indicator light is green
Only use the power adapters included in the package.
Do not place the camera and power cord within the reach of your baby.
Only use the power adapters included in the package.
Do not place the camera and power cord within the reach of your baby.
Once they’re paired successfully, the camera number with icon will be shown at the top left.
Microphone feedback might occur when the monitor is too close to the Please keep them at least 1.5m / 4.9ft apart.
It is recommended to pair in the baby’s room, or wherever you intend to place the

Placing the Camera

Place the camera 2m / 6.6ft away from your baby for safety reason and for a better view when in night vision mode

Wall Mounting Camera

Select the spot to mount the camera, keeping it beyond your baby’s
Insert the screw (not included) pre-installed on wall into the mounting hole of the camera.

It’s strongly recommended to use a screw and screw anchor. Don’t release the camera until you’re sure it is firmly mounted.

FUNCTIONS & OPERATIONS

Monitor Interface overview

	Signal	4 levels
	Current Camera	Camera 1 / Camera 2 / Camera 3/Camera 4
	Zoom	2X/4X
℉	Current Temperature	℃/ ℉
	Cry Detection	???
	Warning	???
	Mute	Mute all system sounds
	Night Vision	Auto ON in a dim environment
	Battery	4 levels

PM12:00

| Current Time| 12Hr/24Hr
| Speaker Volume| 0-7 levels
---|---|---
| Brightness| 1-8 levels

|

Camera

Settings

| Time
Cry Detection
Warning
Temp Unit
Display
Language
Reset
Help

Talkback

Press and hold the Talk button to talk to camera and release to exit. When monitor on Under Split Screen Mode: Press Left / Right Button to select the camera (Camera 1 or 2) you want to talk to. Hold to talk and release to exit.

Digital Zoom & Circulating

Under split screen mode, press Left / Right Button -> OK Button to select the camera (Camera 1 or 2) you want to view or zoom
Press Zoom Button to zoom in to 2X / 4X when viewing the A third pressing of the button will restore to the original image.
Long press “OK” key for 3 seconds, the PTZ will cruise automatically twice, and then press“OK” key again to end the

Pan-n-Tilt

When viewing the camera, press Left / Right / Up / Down Button to view at different angles, 108 degrees vertically and 350 degrees horizontally.

Night Vision

The night vision is automatically activated in a dim environment. The camera has high-intensity infrared LEDs for picking up clear images in the dark. Black and white images can be captured within 6m distance.

Volume Adjustment

Use the volume + – button on the top of monitor to quickly adjust the volume
Or you can press Menu Button: Choose -> Button -> Left / Right Button to volume down / up

Display Brightness Adjustment

Press Menu Button: Choose ->Button ->Left / Right Button to adjust the brightness

Camera

Add Camera Press Menu button, select through -> ADD -> to add a camera

Press and hold the Pair Button on the camera for 3 seconds

Split Screen

Press Menu button, select through -> .
Then select two cameras (Camera 1/2/3/4) for Split screen

Once set, you can view two cameras at one time without delay. The sound of the two rooms will be switched every 15 seconds

Under Split screen mode, you can also press Left / Right Button ->Button to select one camera (Camera 1 or 2) you want to view or zoom in. Press the Button to return to Split screen mode.

View Camera

Press Menu button, select through -> Scan->1 to view a camera.|
If there are 2 or more cameras, select to cyclethrough the added cameras every 15 seconds.

You can switch viewing different cameras; the current camera number will be shown with the Camera icon on the monitor.

Lullabies

Explanation: This function is to comfort baby when
Press Menu button, Choose ->
Select the lullaby you Select -> to play the lullabies in a loop, and press OK again to stop playing.

4）choose Left / Right Button to adjust the volume of the lullaby.

Monitor Settings

Press Menu Button, Left and Right Buttons, and then OK Button to set the monitor 1)Time setting: Set the current time by setting hour, minute, and AM/ PM.
2)Cry Detection:Automatically detect the baby’s crying,wake up the display screen,and send out a prompt tone; the sensitivity can be set to OFF, Low ,middle or High 3)Warning volume: Select between Low, High, and Mute.

Temperature unit: Select between °C and °F.
Display (Screen auto-sleep time): Select between 1min, 2min, 5min, and Always
Language:English, French, German, Spanish, Italian
Reset: Press OK Button to conﬁrm factory resetting screen;“conﬁrm factory resetting screen” will be shown when restoring, and you can’t press any button to control the device during this period. The monitor will auto restart when it’s done
Help: Check the email for customer service

SPECIFICATIONS

Screen

Model	JT-VBM002
Resolution	IPS1920*1080 PPI=400
Image	16:9
Image compression	h.264
Operating Range	600m(antenna vertically positioned at 90°)
Temperature Alert	Yes
Baby Cry Alert	Yes
Volume Control	8 Levels
Brightness	8 Levels
Antenna	Rotatable (max. 90 degree)
Zoom	Zoom In (2X)
	Zoom In (4X)
Auto-Pilot	2 cycles
Two-Way Talk	Max. 4 cameras
Power Input	5V/2A (1.5m long USB C cable)
Storage Temperature	-10°C ~ 55°C / 14°F – 131°
Operation Temperature	0°C ~ 40°C / 32°F – 104°F

Camera

Cmos	2K
Image compression	h.264
Pan-n-Tilt	108 degrees vertical (Up=90, Down=18)

270 degrees horizontal (Left=135, Right=135)

Zoom| Zoom In (2X)

Zoom In (4X)

WARRANTY & CUSTOMER SERVICE

12 months warranty
Lifetime customer service (contacts on the monitor, and back cover of this User Guide)

TROUBLESHOOTING

Product not powering on?

Check that the camera and monitor are turned on.
Check the camera is connected to power properly (it cannot be charged; it’s power off once disconnected from power).
Check that the monitor is of enough battery (it’ll auto shut off when battery level icon flashes red slowly on the monitor).
Check the intactness of the power cable.
Baby monitor can’t connect with the camera?
Check whether the monitor is of low battery. Charge it in time to restore good connection.
Check whether the camera is well connected to power.
Check whether there are any large metallic objects including doors, refrigerators, mirrors, etc., are placed between the camera and monitor thus blocking the radio signals.
Check whether there’s any other 900MHZ product is used nearby , which may interfere the connection.
Check whether the camera is placed on a metallic table Or put it directly on the ground If nothing above is involved, please retry to restart the monitor or to repair the camera: press the Pair Button at the bottom of the camera, press Menu button, select through and then the monitor will auto-pair with the camera.

Too much noise?

-Volume may be set too high. Press volume – button which is on the top of the screen to volume down
-Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.
-The camera may be too out of range. Please keep it within 10m / 32.8ft to the monitor.

The Video is not clear?

-Make sure the camera lens and display screen are clean, otherwise you can use a lens cloth to wipe them.
-Conﬁrm that the camera is not obstructed around

Black and white pictures?

Night vision LED may be ON. Please turn on room lights to force it out of the night mode.

Choppy videos?

-Check whether the camera is near the monitor and that there’re no obstacles between them.
-Adjust the monitor antenna to vertical position for better signal transfer.
Operating bands(Tx and Rx) and maximum power Frequency Band(s):902MHz- 928MHz(TX/RX)

Maximum output power:

Jartoo Baby Monitor: 0.6266W Jartoo Baby Camera: 0.4256W

FCC STATEMENT

**** FCC Radiation Exposure Statement:

**** For Jartoo Baby Monitor:
This equipment complies with FCC radiation exposure limits set forth for an uncon- trolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.
For Jartoo Baby Camera:
This equipment complies with FCC radiation exposure limits set forth for an uncon- trolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.