Dorman 99377 Keyless Entry Remote Owner’s Manual

: June 12, 2024
: DORMAN

Table of Contents

GENERAL TECH TIP:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Dorman 99377 Keyless Entry Remote Owner's Manual

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully. This product is only designed to function properly on specific vehicle applications. Please verify that the vehicle requirements match the product specifications and application notes for this part.

REMOVAL/INSTALL OF KEYLESS ENTRY REMOTE (99377) Ford 201911, Lincoln 201513

GENERAL TECH TIP:

Due to the programming process being sensitive to voltage drops, it is recommended that a battery charger is hooked up to the vehicle before beginning the programming process.

Programming Instructions
DISCLAIMER: Programming additional remotes require at least ONE already programmed remote.
STEP 1: Be sure to have all currently programmed remotes available for this process. Any remotes not present will be erased.
STEP 2: Turn the ignition OFF.
STEP 3: Plug the programming dongle into the OBD II port.

STEP 4: Using a valid remote, press lock and then unlock.
STEP 5: Wait 5 seconds. The programmer will beep a short beep and the green LED will blink.
STEP 6: Wait 20 seconds. The programmer will begin to flash the red LED every second to indicate security access is in progress.
STEP 7: After 10 minutes the programmer will beep and turn on the green LED to indicate security access has been gained.
STEP 8: Press the button to erase all stored key data. This will erase all currently programmed keys to the vehicle. All previously programmed keys must be relearned during this process. The programmer will beep a short beep to denote the button press.
STEP 9: The programmer will then beep a long beep and turn on the green LED to indicate that all keys have been erased.
STEP 10: Place a remote into the programming socket, then press the button on the programmer.
STEP 11: The programmer will beep a short beep and the LED will remain off to indicate that the remote has been detected in the socket.
STEP 12: The red LED will blink until the remote is programmed.
STEP 13: The programmer will beep a long beep and the green LED will turn on to indicate that the key has been successfully programmed.
STEP 14: Remove the programmed remote from the socket. Test the remote by pressing Lock/Unlock.
STEP 15: Place the next remote into the programming socket, then press the button on the programming dongle.
STEP 16: The programmer will beep a short beep and the LED will remain off to indicate that the remote has been detected in the socket.
STEP 17: The red LED will blink until the remote is programmed.
STEP 18: The programmer will beep a long beep and the green LED will turn on to indicate that the key has been successfully programmed.
STEP 19: Remove the programmed remote from the socket. Test the remote by pressing Lock/Unlock.
STEP 20: Repeat steps 15 through 19 for any additional remotes. A maximum of 4 remotes may be learned to the vehicle.
STEP 21: When all remotes have been programmed, unplug the programmer from the OBD II port.

Still need help?
Please call our Technical Support team for assistance from our team of certified automotive experts.
1-800-523-2492

Disclaimer: Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.