EliteControl EC-KP Slimline Hardwired Keypad Instruction Manual
- June 13, 2024
- EliteControl
Table of Contents
EliteControl EC-KP Slimline Hardwired Keypad Instruction Manual
Specifications
Voltage 72VDC
Current Draw 70mA max
Mounting Height (Recommended) 7.2m to 7.Sm
Push Terminals 0.2mm2 – 0.5mm2 security cable
IP Rating IPX0 (indoor use only)
Tamper Calibration & alarm (optional)
Backlighting 3 programmable options
Mounting Vertical flush box or direct fix
Dimensions Hll8 x W74 x 072mm
Warranty 5 years
Fitment
- Fit mounting plate level on the wall.
- Make sure the entire system is powered down.
- Terminate POS, NEG, CLK & DAT as detailed in the ‘Hardware & Cabling Overview’ below
- Place keypad over mounting plate as shown then slide down until a click is heard from the securing clip.
Compatible Control Panels
EC-i, ESL-2, ESL, Elite S, Elite S Lite, ESX V2 & Runner
Programming & Display
Ensure the keypad is mounted to its backplate (on the wall) before use. This is imperative to ensure the capacitive touch calibrates correctly.
The EC-KP best programs & displays up to 8 x Inputs, 8 x Outputs, 8 x Areas, 8 x Keypads, 8 x Schedules & 8 x Holidays. Some programming values over ‘8’ are available, however these are not recommended on the EC-KP due to the nature of the display.
Systems greater than 8 inputs, 8 outputs etc are best programmed via the EC- TOUCH, EC-LCD, web browser or EliteCloud dashboard (coming soon). It is recommended to use the EC-KP along with the EliteCloud smartphone app for the best user experience.
Hardware & Cabling Overview
Button & Icon Overview
Menu (Programming & Diagnostics)
- Press the Info icon (i) found on the home screen to access the menu.
- Each number represents the following functions from within the menu:
- Installer Programming – Requires installer code to access this function.
- Alarms/Activations – Shows activated inputs from the previous arm cycle (only displays inputs 7 – 8).
- Current System Faults – Each fault within option 3 is indicated by a number as detailed below:
- System Tamper Alarm
- Input Tamper Alarm (wired or wireless)
- Supervision Alarm
- Fuse Failure
- Communicator Failure
- Wireless Device Battery Low
- Remote Battery Low
- Excessive Wrong Code Attempts
- Sleep Options – Select the preferred option from 7 – 3 below then press ✔ to confirm.
- Illumination will time out after 30 seconds & will only wake when touched.
- Illumination will time out after 30 seconds & will wake with any sensor movement.
- Illumination is on continuously.
- Brightness – 7 = Least bright & 6 = Most bright. Once selected, press .✔ to confirm.
- Beep/Buzzer – 7 = Lowest frequency & 9 = Highest frequency. O = Beep/Buzzer OFF Select the preferred option followed by ✔ to confirm.
- Open/Active Inputs – Displays any input (from 7 – 8 only) that is open/active. Open/Active inputs above 8 can not be viewed on the EC-KP due to the nature of the display.
The best UX is achieved by pairing the EC-KP with the EliteCloud smartphone opp.
Installer Programming
➔] Enter Installer Programming from the home screen
- Press the ‘Info Button ‘ (i) & options l – 7 will appear.
- Press option l to access installer programming & (i) will slow flash white.
- Enter the correct installer code (default 000000) followed by ✔ to confirm.
- (i) will fast flash white to indicate you are in installer programming.
← ] Exit Installer Programming
- Press the ‘Cancel’ button several times until you return to the ‘Home Screen’.
Keypad Address
Setting or Retreiving the Keypad Address
-
Enter installer programming as detailed above:
Make sure (i) is fast flashing white to indicate that you are in programming mode before proceeding. -
Press 902 followed by the ✔ icon & the current keypad address will flash back on the numeric display.
-
Next enter the new keypad address followed by the ✔ icon to confirm. The new address will flash back.
Note: All keypads on one system must be set to their own independent address to help avoid bus conflict.
- Press the ‘Cancel’ button 2 times to exit back to the ‘Home Screen’.
Address Type Programming
Address programming is available via the EC-KP, however some addresses are
restricted on this keypad.
Below is a summary of the most common programming addresses for ESL & EC-i.
Make sure you are in installer programming as detailed above before
proceeding.
Important
Manufactured by Arrowhead Alarm Products Ltd – www.aap.co.nz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>