HAVIT Lighting HV2871T-BLK-12V Dome Deck Light Owner’s Manual
- June 11, 2024
- Havit Lighting
Table of Contents
HAVIT Lighting HV2871T-BLK-12V Dome Deck Light
FAQ
Frequently Asked Questions
- Q: Is the Dome Deck Light dimmable?
- A: No, the Dome Deck Light is not dimmable.
- Q: What is the warranty period for the Dome Deck Light?
- A: The Dome Deck Light comes with a warranty of 3 Years Replacement*.
Product Specifications
Product Specifications
Model No.| HV2871T-BLK-12V| HV2871T-SLV-12V| HV2872T-BLK-12V| HV2872T-SLV-12V
Name| Dome| Dome
Material| Aluminium Cover + PC Body| Aluminium Cover + PC Body
Colour| Black| Silver| Black| Silver
IP Rating| IP65| IP65
Installation Type| Ground or Wall – Recessed| Ground or Wall – Recessed
Input Voltage| 12v DC| 12v DC
Protection Class| 3 (Low Voltage)| 3 (Low Voltage)
Lamp Base| Built in LED| Built in LED
Protection Class| (Low Voltage)| (Low Voltage)
Lamp Wattage| 1x 3w| 2x 3w
Colour Temp| Tri Colour – 3000k, 4000k, 5500k| Tri Colour – 3000k, 4000k,
5500k
Lumens| 180lm, 185lm, 190lm| 2x 180lm, 2x 185lm, 2x 190lm
CRI| > 80| > 80
Wiring| Parallel| Parallel
Dimmable| No| No
Warranty| 3 Years Replacement| 3 Years Replacement
Sample Wiring Diagram
Adequate Drainage Diagram
Dimensions
HV2871T Dimensions
HV2872T Dimensions
Important Safety Issues
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- Aluminium and 304SS fittings must not be installed within 5km of any salt water environments.
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off)
- Make a hole where fitting is to be placed using dimensions provided on line drawings,
- Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
- Connecting the cable – If more than one fitting installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together
- Then connect neutral cables together, Neutral cables are marked for selection of colour temperature. If 3000k or 5500k is selected you must terminate extra cable to be IP Rated to avoid any water making contact with internal parts of cable. To get 4000k, Join both 3000k + 5500k together and connect to neutral on cable run.
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Insert fitting into hole.
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
More Information
Must be installed by a licensed electrician
Contact Details
- 143 Beauchamp Road
- Matraville NSW 2036 Australia
- Tel: 02 9381 8300
- Fax: 02 9666 8881
- Email: sales@havit.com.au
- Web: www.havit.com.au
**Warranty Terms & Conditions***
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>