HAVIT Lighting Bata Recessed Brick Light Installation Guide
- June 4, 2024
- Havit Lighting
Table of Contents
HAVIT Lighting Bata Recessed Brick Light
Important Safety Issues:
- This product must be installed by a qualified electrician accord-ing to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installa-tion.
- Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- Aluminium and 304SS fittings must not be installed within 2km of any salt water environments.
- When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Dimensions
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Make a hole where fitting is to be placed using dimensions provided on line drawings
- Insert canister, and ensure that the top is level with wall. Failure to do so will void warranty.
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Remove screws from face, remove face and glass and set aside.
- Remove PCB from fitting
- Attach body of fitting to canister making sure body sits just behind canister edge.
- Reattach PCB to fitting.
- Colour temperature is preset to 3000k, to change slide switch located on front of PCB to desired colour temperature.
- Reinsert glass and then reattached face making sure screws are tight to avoid any water penetration.
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Product Specifications
Model No.| HV3003T-BLK-12V| HV3004T-BLK-12V| HV3003T-SS316-12V| HV3004T-
SS316-12V
Name| Bata
Material| 316 Stainless Steel + Aluminium
Colour| Black| Stainless Steel
IP Rating| IP54
Input Voltage| 12v DC
Lamp Base| Built in LED
Lamp Wattage| 1x 10w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 800lm, 850lm, 900lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 2 Years Replacement*
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email : sales@havit.com.au
Web: www.havit.com.au
**Warranty Terms & Conditions***
Additional Information
Documents / Resources
|
HAVIT Lighting Bata Recessed Brick
Light
[pdf] Installation Guide
Bata Recessed Brick Light, Bata Recessed Light, Recessed Light, Brick Light,
Beta Light, Light
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>