HAVIT Lighting 9 in 1 Tivah Fixed Down Instruction Manual
- June 4, 2024
- Havit Lighting
Table of Contents
HAVIT Lighting 9 in 1 Tivah Fixed Down
9in1 Tivah Fixed Down Installation Instructions
Product Specifications
| Model No. | HV1105T | HV1115T | HV1125T | HV1135T | HV1145T | HV1185T | HV1195T |
|---|---|---|---|---|---|---|---|
| Name | Tivah | ||||||
| Material | 316 Stainless Steel | Solid Copper | Aluminium | Aluminium | Aluminium | ||
| Aluminium | Solid Brass | ||||||
| Colour | Stainless Steel | Copper | Black | White | Silver | Titanium | Antique Brass |
| IP Rating | IP65 | ||||||
| Input Voltage | 240v AC | ||||||
| Lamp Base | GU10 | ||||||
| Lamp Wattage | 3w, 5w, 7w | ||||||
| Colour Temp | TRI Colour – 3000k, 4000k, 5500k | ||||||
| Lumens | 240-560lm, 255-595lm, 270-630lm | ||||||
| CRI | > 80 | ||||||
| Wiring | Parallel | ||||||
| Dimmable | No (with globe supplied) | ||||||
| Warranty | 2 Years Replacement* |
Dimensions
Important Safety Issues
-
This product must be installed by a qualified electrician according to AS/NZS 3000.
-
Ensure all electrical mains are disconnected before any installation.
-
Do not exceed maximum wattage restrictions for globes:
240V GU10 = 35w / 12V MR16 = 20w -
Modification of this product will void any warranty.
-
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
-
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
-
Aluminium and 304SS fittings must not be installed within 2km of any saltwater environments.
-
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
-
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
-
All o-rings and seals must be in place correctly to maintain warranty.
-
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen allen screws on side of base and seperate mounting bracket from fitting.
- Install the backing plate securely using appropiate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
- Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
- Affix the fiiting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
- Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
- Colour temperature and wattage is preset to 3000k and 7w, to change remove cover from fitting by twisting anti-clockwise and set aside. Remove globe and select desired colour temperature and wattage by moving switches on side of globe and reinserting globe into lamp holders.
- Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Changing Globe
- Remove the cover by twisting anti-clockwise and set aside, remove globe by also twisting anti-clockwise.
- Re-insert the appropriate globe by inserting the 2 circular pins into the lamp holder and twisting clockwise. (Make sure not to exceed max wattage, see product label for correct info)
- Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
Must be installed by a licensed electrician
Contact Details
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881 Email: sales@havit.com.au Web:
www.havit.com.au
Warranty Terms & Conditions
Additional Information
Tivah Fixed Down 5w GU10 Installation Instructions
Product Specifications
Model No.| HV1107GU10T| HV1117GU10T| HV1127GU10T| HV1137GU10T| HV1147GU10T|
HV1187GU10T| HV1197GU10T
---|---|---|---|---|---|---|---
Name| Tivah
Material| 316 Stainless Steel| Solid Copper| Aluminium| Aluminium| Aluminium|
Aluminium| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Titanium| Antique Brass
IP Rating| IP65
Input Voltage| 240v AC
Lamp Base| GU10
Lamp Wattage| 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 270lm, 285lm, 300lm
CRI| > 80
Wiring| Parallel
Dimmable| No (with globe supplied)
Warranty| 2 Years Replacement*
Dimensions
Important Safety Issues
-
This product must be installed by a qualified electrician according to AS/NZS 3000.
-
Ensure all electrical mains are disconnected before any installation.
-
Do not exceed maximum wattage restrictions for globes:
240V GU10 = 35w / 12V MR16 = 20w -
Modification of this product will void any warranty.
-
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
-
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
-
Aluminium and 304SS fittings must not be installed within 2km of any saltwater environments.
-
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
-
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
-
All o-rings and seals must be in place correctly to maintain warranty.
-
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen allen screws on side of base and seperate mounting bracket from fitting.
- Install the backing plate securely using appropiate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
- Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
- Affix the fiiting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
- Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
- Colour temperature and wattage is preset to 3000k and 7w, to change remove cover from fitting by twisting anti-clockwise and set aside. Remove globe and select desired colour temperature and wattage by moving switches on side of globe and reinserting globe into lamp holders.
- Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Changing Globe
- Remove the cover by twisting anti-clockwise and set aside, remove globe by also twisting anti-clockwise.
- Re-insert the appropriate globe by inserting the 2 circular pins into the lamp holder and twisting clockwise. (Make sure not to exceed max wattage, see product label for correct info)
- Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
Must be installed by a licensed electrician
Contact Details
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881 Email: sales@havit.com.au Web:
www.havit.com.au
Warranty Terms & Conditions
Additional Information
Tivah Fixed Down 5w MR16 Installation Instructions
Product Specifications
Model No.| HV1107MR16T| HV1117MR16T| HV1127MR16T| HV1137MR16T| HV1147MR16T|
HV1187MR16T| HV1197MR16T
---|---|---|---|---|---|---|---
Name| Tivah
Material| 316 Stainless Steel| Solid Copper| Aluminium| Aluminium| Aluminium|
Aluminium| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Titanium| Antique Brass
IP Rating| IP65
Input Voltage| 12v DC
Lamp Base| MR16
Lamp Wattage| 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 270lm, 285lm, 300lm
CRI| > 80
Wiring| Parallel
Dimmable| No (with globe supplied)
Warranty| 2 Years Replacement*
Dimensions
Important Safety Issues
-
This product must be installed by a qualified electrician according to AS/NZS 3000.
-
Ensure all electrical mains are disconnected before any installation.
-
Do not exceed maximum wattage restrictions for globes:
240V GU10 = 35w / 12V MR16 = 20w -
Modification of this product will void any warranty.
-
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
-
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required, if not within this allowance warranty will be voided.
-
Aluminium and 304SS fittings must not be installed within 2km of any saltwater environments.
-
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
-
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
-
All o-rings and seals must be in place correctly to maintain warranty.
-
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen allen screws on side of base and seperate mounting bracket from fitting.
- Install the backing plate securely using appropiate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
- Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
- Affix the fiiting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
- Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
- Colour temperature and wattage is preset to 3000k and 7w, to change remove cover from fitting by twisting anti-clockwise and set aside. Remove globe and select desired colour temperature and wattage by moving switches on side of globe and reinserting globe into lamp holders.
- Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Changing Globe
- Remove the cover by twisting anti-clockwise and set aside, remove globe by also twisting anti-clockwise.
- Re-insert the appropriate globe by inserting the 2 circular pins into the lamp holder and twisting clockwise. (Make sure not to exceed max wattage, see product label for correct info)
- Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
Must be installed by a licensed electrician
Contact Details
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881 Email: sales@havit.com.au Web:
www.havit.com.au
Warranty Terms & Conditions
Additional Information
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>